Subscribe to Our Youtube Channel
Related Manuals for Vivo STAND-PDMH
Summary of Contents for Vivo STAND-PDMH
- Page 1 Height Adjustable Podium SKU: STAND-PDMH Instruction Manual Assembly Video & Product Info www.vivo-us.com/products/stand-pdmh...
-
Page 2: We're Here For You
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. -
Page 3: Package Contents
Package Contents A (x1) C (x1) B (x1) Lower Back Base Top Panel Panel D (x1) E (x1) F (x1) Upper Back Lower Upper Support Panel Support Panel Panel I (x1) H (x1) G (x1) Lower Right Lower Left Backstop Panel Panel K (x1) -
Page 4: Included Hardware & Tools
Included Hardware & Tools S-A (x12) S-B (x31) S-C (x31) S-D (x2) Wooden Cam Lock Cam Lock ST4.2x13mm Dowel Pin Screw Screw S-E (x4) S-F (x10) S-G (x4) M5x20mm M6x12mm M6x25mm Screw Screw Screww T-A (x1) 4mm Allen Wrench Tools Needed: Weight Capacity: 11lbs (5kg) -
Page 5: Assembly Steps
ASSEMBLY STEPS STEP 1 Insert Cam Lock Screws (S-C) using a Phillips screwdriver and Wooden Dowel Pins (S-A) into the Upper Left Panel (J) and Upper Right Panel (K). Alternate Cam Lock and Wooden Dowl Pins. STEP 2 Insert the Upper Left Panel (J) and Upper Right Panel (K) into the sides of Upper Back Panel (D) making sure the taller ends of the left and right panels are on the same side as the Pilot Holes as shown. - Page 6 STEP 3 Insert the Cam Lock Nuts (S-B) into the Upper Back Panel (D) making sure the arrow is facing towards the Cam Lock Screws (S-C). Using a Phillips screwdriver, turn the Cam Lock Nuts (S-B) clockwise 90 degrees to secure.
- Page 7 STEP 4 Secure Mounting Bracket (M) to the Adjustable Column (L) using M6x12mm Screws (S-F) and 4mm Allen Wrench (T-A). The Mounting Bracket should overhang the front of the Column with the Handle on the right side, as shown. Handle WARNING To prevent injury or damage to equipment and your surroundings,...
- Page 8 STEP 5 Secure the Column Assembly and Handle to Top Panel (B) using M6x12mm Screws (S-F) and 4mm Allen Wrench (T-A). Column Assembly STEP 6 Screw Cam Lock Screws (S-C) into Top Panel (B) and insert into Upper Assembly.
- Page 9 STEP 6 - Cont’d Insert the Cam Lock Nuts (S-B) into the Upper Assembly making sure the arrow is facing towards the Cam Lock Screw (S-C). Secure by turning clockwise 90 degrees with a Phillips screwdriver. Secure the Column Assembly to Upper Back Panel (D) using ST4.2x13mm Screws (S-D) and a Phillips screwdriver.
- Page 10 STEP 7 Insert Wooden Dowel Pins (S-A) into Upper Back Panel (D), then install Upper Support Panel (F). Secure using M5x20mm Screws (S-E) and a Phillips screwdriver. STEP 8 Screw Cam Lock Screws (S-C) into Lower Back Panel (A).
- Page 11 STEP 8 - Cont’d Insert Lower Support Panel (E) into Lower Back Panel (A), making sure the holes on the Lower Support Panel are facing towards the longer section. Insert the Cam Lock Nuts (S-B) into the Lower Support Panel (E) making sure the arrow is facing towards the Cam Lock Screws and secure by turning clockwise 90 degrees with a Phillips screwdriver.
- Page 12 STEP 9 Insert Wooden Dowel Pins (S-A) and Screw Cam Lock Screws (S-C) into Lower Left and Right Panels (H,I) using a Phillips screwdriver. Peel paper from Foam Blocks (N) and stick to Lower Left and Right Panels (H,I) approximately 2” (50mm) from the top of panels and 3” (80mm) from the back of panels. 3”...
- Page 13 STEP 10 Insert Lower Left and Right Panels (H,I) into Lower Assembly. Lower Assembly Secure by inserting Cam Lock Nuts (S-B) into Lower Assembly making sure the arrows on the nuts are facing towards the Cam Lock Screws. Tighten by turning clockwise 90 degrees using a Phillips screwdriver.
- Page 14 STEP 11 Screw Cam Lock Screws (S-C) into top of Base (C) using a Phillips screwdriver. Top of Base Peel the paper from Pads (O) and stick to bottom of Base (C). Bottom of Base...
- Page 15 STEP 12 Slide the Lower Assembly over the Cam Lock Screws (S-C) on Base (C). Lower Assembly Insert the Cam Lock Nuts (S-B) into the Lower Assembly making sure the arrow is facing towards the Cam Lock Screw (S-C). Secure by turning clockwise 90 degrees with a Phillips screwdriver.
- Page 16 STEP 13 With the Upper Assembly positioned upside down, slide the Lower Assembly over the Adjustable Column (L) to where the column slides through the plastic insert on the Lower Support Panel (E). Lower Assembly Upper Assembly When sliding on, make sure the Foam Blocks (N) on the Lower Assembly don’t get pulled off and slide on the outside of the Upper...
- Page 17 STEP 14 With the help of another individual, flip the podium upright. 2 Person Assembly is Recommended Insert Wooden Dowel Pins (S-A) and screw Cam Lock Screws (S-C) into the Backstop (G) using a Phillips screwdriver.
- Page 18 STEP 14 - Cont’d Insert Backstop (G) into the front of the Top Panel (B). Insert the Cam Lock Nuts (S-B) into the bottom of Top Panel (B) making sure the arrow is facing towards the Cam Lock Screw (S-C). Secure by turning clockwise 90 degrees with a Phillips screwdriver.
- Page 19 STEP 15 Peel paper from Stickers (P) and stick over the Cam Lock Nuts (S-B). STEP 16 Firmly grip the Top Panel (B) and pull the handle to adjust the height of the podium. Handle will be loose during transport Tighten knob to ensure handle does not shake DO NOT press handle while...
-
Page 20: Last Updated
LAST UPDATED: 07/23/24 REV1 v1.0 Need Help? Get In Touch Monday-Friday from 7:00am-7:00pm CST help@vivo-us.com www.vivo-us.com 309-278-5303 Chat live with an agent! FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us...
Need help?
Do you have a question about the STAND-PDMH and is the answer not in the manual?
Questions and answers