Related Manuals for MUNBYN IMC30
Summary of Contents for MUNBYN IMC30
- Page 1 Version 1.00 IMC30 Banknote Counter User Manual MORE CHOICE FOR YOUR GROWING BUSINESS MORE CHOICE FOR YOUR IMC30 GROWING BUSINESS...
-
Page 2: Table Of Contents
4.2.3.Multi-currency Counting Mode ------------------------------- 4.2.4.Non-Volatile Memory for Currency Mode -------------------- 4.3.Counting Function Options ------------------------------------- 4.3.1.Automatic Banknote Counting ------------------------------- 4.3.2.SN Reading ------------------------------------------------------ 4.3.3.Batch Setting --------------------------------------------------------- 4.3.4.Accumulation --------------------------------------------------- 4.4.Counting Speed Setting ----------------------------------------- 4.5.Check Detail of Counting -------------------------------------------- 4.5.1.Check the Serial Number ------------------------------------------- IMC30 IMC30... -
Page 3: Machine Overview
Figure 1-1 banknote counter Front Diagram Figure 1-3 banknote counter Top Diagram Adjustable SD Card Port Screw Handle of External Back Cover Display Port Speaker RS232 Printer Port Power Cord Jack Switch On/Off Figure 1-2 banknote counter Back Diagram IMC30 IMC30... -
Page 4: Packing Open And Installation
Used for the CIS Paper calibration Power Supply Nylon Brush Clean the machine Power Cord Clean the CIS or the Soft Cleaning Cloth Connector other sensors Slotted screw driver Figure 2-2 Power and External Display Connection User Manual 铭牌没改 IMC30 IMC30... -
Page 5: Banknote Guider Installation
Mode key, to select CNT mode, SDC mode, or MDC mode for counting. Query key, to check the detailed counted information. START/STOP key, to start counting, or to start other operations. Figure 3-1 Display Appearance IMC30 IMC30... -
Page 6: Display Interface
The default mode is MDC mode. By pressing the key the control panel, three counting modes can be cyclically switched, and the 3 counting modes will be cyclically switched according to the SDC-MDC-CNT sequence. IMC30 IMC30... - Page 7 In this mode, acquisition, magnetic detection, ultraviolet detection, and double note the banknote counter has 2 counting speed detection. While in the CNT mode, there is only a double note detection (800/1000/1200 pcs/min) options. function. IMC30 IMC30...
-
Page 8: Automatic Recognition Mode
Figure 4-8. Figure 4-5 Currency Selection Interface Figure 4-7 Multi-Currency Selection Figure 4-8 Multi-currency Counting Mode Note: Only MDC mode is effective in the multi-Currency mode. Figure 4-6 Auto Recognition Counting Interface IMC30 IMC30... -
Page 9: Non-Volatile Memory For Currency Mode
The default setting of automatic counting is on. Every time the banknote counter resets, the setting will be reset to be on state. Figure 4-11 Batch Setting Interface IMC30 IMC30... -
Page 10: Accumulation
As shown in Figure 4-15, if the SN reading is on, press the required, the different counting speeds can be switched QUERY key again, the banknote’s serial number will by pressing the SPEED key in any counting mode. be shown in the following figure. IMC30 IMC30... -
Page 11: Print Information
Figure 4-19, and then press the Print key again, and the printer starts printing. Figure 4-16 open the cover Insert a roll of paper in the direction shown in the Figure 4-17. Figure 4-19 close the cover IMC30 IMC30 Figure 4-17 Insert paper... -
Page 12: Menu Setting
Figure 5-1 Menu Interface Figure 5-3 Service Menu 5.1. Service Menu 5.1.1. Device Check Press the MENU key to enter the service menu, you will be requested to input a password with the following interface. The default password is 6666. IMC30 IMC30... - Page 13 If you meet any problem about use, please take a photo of this page and contact us. IR Calibration: Press the Direction keys to choose this option, press the Menu key to start the IR Calibration. Figure 5-7 Batch Gather IMC30 IMC30...
-
Page 14: System Setting
Start key to start device aging mode, and the device will run automatically for half of an hour. Press ESC key to exit. Figure 5-10 System Setting You can set the basic functions of the machine or reset the machine. IMC30 IMC30... -
Page 15: Language Select
You can format the SD card you insert to the money Figure 5-12 Bill Total Count counter, all data in the SD card will be cleared. This will show the total number of all the banknote you have counted. IMC30 IMC30... -
Page 16: Parameter Setting
MAG: Magnetic image feature. 5.1.3.3. Identify Level Figure 5-14 Device Parameter Save Mode: Retain the status before device startup. False Count: Counterfeit counter switch. Boot Preset: Batch mode is enabled by default during device startup. Figure 5-16 Identify Level IMC30 IMC30... -
Page 17: Version Information
SD card root directory, restart the device, and the program will be automatically upgraded. Import Setting: For factory use, please do not operate at will. Export Setting: For factory use, please do not operate at will. Figure 5-17 Time Setting 5-18 IMC30 IMC30... -
Page 18: Maintenance
It will damage and cause malfunction of the (tight). machine. Turn it anticlockwise to increase gap in order to reduce For more troubleshooting methods, please refer to the friction (loose). banknote counter maintenance manual. Figure 6-1 Adjustable Screw IMC30 IMC30... -
Page 19: Technical Parameters
200 notes banknote counter, please contact us. Power Supply AC 100～ 240V 土10%,50/60HZ Current MUNBYN provides 18 months warranty and lifetime Maximum 1.8A（100N 240 VAC) Power Consumption free service. Power Consumption <40 Watts If you encounter any issues with the product, please contact the MUNBYN team to promptly receive 0°CN 35°C(Operating)
Need help?
Do you have a question about the IMC30 and is the answer not in the manual?
Questions and answers