1.01 function issue? • Update section 2.3 How to remove a stuck banknote or bill? 2021-6-21 James Hu 1.02 • Update section 2.6 When and how do I adjust the feeding gap adjustment? Page2of17 IMC08 Frequently Asked Questions Version 1.02...
1.1. What currencies does the IMC08 supports?................4 1.2. Does the IMC08 recognize serial numbers?................4 1.3. Does the IMC08 work with a printer? ..................4 1.4. How does the external display work? ..................4 1.5. Does the IMC08 have batch/bundling capability? ..............4 1.6.
1.5. Yes, the IMC08 has batch function for bundling. The capacity of the stacker is 200. However, you can set the batch number from 0 to 998. For example, if you set the batch number to 50, when you put 200 notes in the hopper, the IMC08 will stop once the counted quantity gets to 50 for you to bundle or strap the bills.
Remove the banknote, clean the CIS sensor; Perform the CIS calibration; Collect data of the banknote. How do I clean the IMC08? 2.2. Please follow the following steps to clean the machine. Before cleaning the machine, please turn off the machine first.
Page 6
Figure 2-3 Back Cover Opened b) As shown in the following figures, clean the marked with cleaning cloth or nylon brush respectively. Lower CIS MG Sensor UV Sensor Other Sensors Figure 2-4 Lower Sensors Page6of17 IMC08 Frequently Asked Questions Version 1.02...
If the bills are stuck inside the feeding port, please turn off the machine and rotate the banknote processing wheel down. CAUTION: ALWAYS ENSURE MACHINE IS OFF BEFORE PUTTING HANDS/FINGERS NEAR THE PROCESSING WHEEL OR SLOT. Figure 2-7 PS1 Error Page7of17 IMC08 Frequently Asked Questions Version 1.02...
Page 8
ALWAYS ENSURE MACHINE IS OFF BEFORE PUTTING HANDS/FINGERS IN THE INSIDE OF MACHINE. 2.3.3. Bill was stuck in the reject pocket (TD Error) When a bill is stuck in the reject pocket of IMC08, a TD Error will appear. Please follow the method below to remove the banknote. Page8of17 IMC08 Frequently Asked Questions Version 1.02...
“main motor error”, the hopper sensor is too sensitive. Figure 2-7 Use Marker Pen to Decrease the Sensitivity of Hopper Sensor Please use the marker pen to paint a little on the hopper sensor as shown in the above figure. Page9of17 IMC08 Frequently Asked Questions Version 1.02...
To fine tune the feeding gap, do the following: 1) Turn off the auto counting feature. 2) Insert one banknote into the gap between the rollers to check if the banknote can be inserted smoothly, as shown in the following. Page10of17 IMC08 Frequently Asked Questions Version 1.02...
Page 11
Figure 2-13 One Coin to Rotate the Screw The IMC08 needs different gaps for different currencies, but otherwise should stay consistent. Having the correct feeding gap adjusted will ensure smooth operation as well as a trouble-free experience. You may need to do some trial and error before getting it perfectly smooth.
Figure 2-14 Main Menu Figure 2-15 Service Menu 2) Click the “CIS Calibration” option, shown below: Figure 2-16 CIS Calibration Interface 3) Open the back cover to clean the CIS sensors with a lint-free cleaning cloth. Page12of17 IMC08 Frequently Asked Questions Version 1.02...
Page 13
4) Using the included CIS calibration sheet (white paper), place inside as seen below, and close the back covers. Figure 2-19 Place the CIS Calibration Paper 5) Start CIS calibration by pressing the “RESTART” button. Page13of17 IMC08 Frequently Asked Questions Version 1.02...
Figure 2-21 Service Menu Figure 2-22 Default Setting Interface 2) After pressing start, the IMC08 will reset all the changed settings beforesettings to factory default. Figure 2-23 Default Setting Guide 3) The processing wheels and rollers in the IMC08 will run for a while.
1) Enter the main menu, and go to the service menu with the password “9999”, as shown in the following screenshots. Figure 2-25 Menu and Service Menu 2) Choose “④Function Setting” and press enter. You will see the following. Page15of17 IMC08 Frequently Asked Questions Version 1.02...
2) Check if the joint of optocoupler is tightly connected as the PICTURE 1 and VIDEO 1 shows. If the joint is fixed tightly, do the next step. 3) Follow the video 2 to exchange the position for both optocoupler. This way can effectively deal with the motor error issue. Video 1:http://munbyn.biz/IMC08-MORTOR-ERROR-VIDEO-1 Video 2:http://munbyn.biz/IMC08-MORTOR-ERROR-VIDEO-2 Page16of17 IMC08 Frequently Asked Questions Version 1.02...
Page 17
Scan the QR code for Facebook online chat Contact us Email: support@munbyn.com Whatsapp: +86-17817881067 If you meet any problem during using the IMC08, please contact us. Page17of17 IMC08 Frequently Asked Questions Version 1.02...
Need help?
Do you have a question about the IMC08 and is the answer not in the manual?
Questions and answers