Table of Contents
Advertisement
Hypermodel™ Amp Dump
The Amp Dump menu allows archiving of just the Genesis3 Amp HyperModels™ to a sysex librarian, or MIDI record-
ing device.This is useful for making a backup copy of your customized Amp HyperModels™, or loading your
HyperModels™ into another Genesis3.The procedure for performing a Sysex Preset Dump is as follows:
1. Connect a MIDI cable from the Genesis3 MIDI Out to the the MIDI In of a MIDI recording device or the MIDI in of
another Genesis3.
2. Press the AMP SAVE and STORE once.The LED in the Utility button will light indicating you are in the Utility
section.
3. Using the TAP-IT or EDIT buttons, scroll to the left or right until the alpha-numeric Display shows
AMPDMP (Amp Dump).The numeric Display will show U1 indicating that the Genesis3 is ready to dump Amp num-
ber 1.
4. Use the DATA KNOB to select the Amp number you wish to send out.
5. Press the STORE button once.The Display reads SND TO which is asking you to select the destination User Amp
location.
6. Use the DATA KNOB to select the destination User Amp number.
7. Set the MIDI recording device to record.
8. Press the STORE button again.The Display reads AMPSND until the dump is complete at which time the Display
briefly reads DONE before it returns to showing AMPDMP.
9. Press the AMP SAVE and STORE buttons simultaneously again to return to the Genesis3 Presets.
MIDI Mapping
The MIDI Mapping in the Genesis3 allows any of the Factory, or User Preset to be accessed from external MIDI pro-
gram change commands which may not necessarily correspond to the desired Genesis3 Preset.This is useful when mul-
tiple MIDI devices are chained together and are all controlled by one central unit. For example, the main MIDI con-
troller can send out a program change command telling a particular MIDI unit to change to Program 10, but you may
want the Genesis3 to change to User Preset 27.You can remap the Genesis3 so when it receives MIDI Program change
10, it calls up User Preset 27. The Procedure for mapping MIDI program changes is as follows:
1. Press the AMP SAVE and STORE buttons simultaneously. Both buttons will light indicating you are in the Utilities.
2. Press the TAP-IT or EDIT Buttons until the alpha-numeric Display shows M
3.With the digit to the right of the M blinking, use the DATA knob to select the incoming MIDI program number you
wish to remap.
4.When the incoming MIDI program number has been selected, press the EDIT button.The digit in the red numeric
Display will begin to flash.This number represents the Preset number within the Genesis3 that will be accessed when
the Genesis3 receives the MIDI program number shown to the right of the M in the alpha-numeric Display.
5. Rotate the DATA knob to select the desired Preset number the Genesis3 will recall when it receives the selected
MIDI program change.
6. Press the AMP SAVE and STORE buttons simultaneously again to return to the Genesis3 Presets.
MIDI Merge
The MIDI Merge function is used to echo the incoming MIDI data to the MIDI OUT/THRU port of the Genesis3.
This is necessary when multiple MIDI devices are chained together and you want to pass the incoming MIDI Data on
to MIDI devices downstream from the Genesis3.The procedure for enabling or disabling the MIDI Merge function is as
follows:
1. Press the AMP SAVE and STORE buttons simultaneously. Both buttons will light indicating you are in the Utilities.
2. Press the TAP-IT or EDIT buttons until the alpha-numeric Display shows MMERGE (MIDI Merge).The red numeric
display will read either On (on) or OF (off) depending upon the current status of the MIDI merge function.
3. Rotate the DATA knob to select the desired status.
4. Press the AMP SAVE and STORE buttons simultaneously again to return to the Genesis3 Presets.
Other Functions
1>U.
35
Advertisement
Table of Contents
