Delta Electronics Programmable Logic Controller DVP-EH Series Instruction Sheet

Warning
Always read this instruction sheet thoroughly before using DVP EH digital I/O extension unit.
This is an OPEN TYPE extension unit. The extension unit should be kept in an enclosure away from airborne, dust,
high humidity, electric shock risk and vibration. Also, it is equipped with protective methods such as special tools or
keys to open the enclosure, so as to avoid the hazard to users and damage the extension unit.
DO NOT connect AC main circuit power supply to any of the input/output terminals, as it will damage the extension
unit. Check all the wiring prior to power up. DO NOT touch terminals when power on.
Introduction
Thank you for choosing Delta DVP-EH series PLC. The main processing units offer 8 ~ 48 points and the
maximum input/output can be extended up to 256 points.
Product Profile and Outline
5 2
7 5 2
5 7
5
4
1
4
3 3
7
3
Dimension (mm)
Model
Length Width
DVP08HM11N 90 40
DVP16HM11N 90 55
DVP08HN11R/T 90 40
DVP16HP11R/T 90 55
6
9 2 8
7 1 6 6
Dimension (mm)
Model
Length Width
4
10
DVP32HN00R/T 90 143.5
11
3
DVP32HP00R/T 90 143.5
3 3
7 DVP48HP00R/T 90 174
1. Power, low voltage indicators 5. Extension wiring 9. Cover
2. I/O terminals 6. Extension port cover 10. Input indicators
3. DIN rail clip 7. Direct mounting holes 11. Output indicators
4. DIN rail 8. Model name
DVP EH Series Model
Input unit Output unit
Model Power
Points Type Points Type
DVP08HM11N 8 0
N/A
DVP16HM11N 16 0
DVP08HN11R 0 8
DVP08HP11R 4 4 Relay: 250V AC/30V DC 2A/1point
DC Type
24V DC
Sink/Source
DVP16HP11R 8 8
DVP08HN11T 0 8
DVP08HP11T 4 4 Transistor: 5 ~ 30V DC 0.3A/1point at 40° C
DVP16HP11T 8 8
Input unit
Model Power
Points Type Points
DVP32HN00R 0 32
DVP32HP00R 16 16
DVP48HP00R 24 DC Type 24
100 ~ 240V
AC
DVP32HN00T 0 Sink/Source 32
DVP32HP00T 16 16
DVP48HP00T 24 24
Specifications
Electrical Specification
Model 08HM11N
08HN11R/T 08HP11R/T 16HP11R/T 32HN00R/T
Item 16HM11N
Power supply voltage 24V DC (20.4 ~ 28.8V DC) (-15% ~ 20%)
Power consumption 1W/1.5W 1.5W 1.5W 2W
24V DC supply current NA NA NA NA
Power protection 24V DC output with short-circuit protection
Voltage withstand 1,500V AC (Primary-secondary), 1,500V AC (Primary-PE), 500V AC (Secondary-PE)
Insulation resistance > 5 M at 500V DC (Between all input/output and earth)
ESD: 8KV Air Discharge, EFT: Power Line: 2KV, Digital I/O: 1KV, Analog &
Noise immunity Communication I/O: 250V,
Digital I/O: 1KV, RS: 26MHz ~ 1GHz, 10V/m
The diameter of grounding wire cannot be smaller than the wire diameter of the terminals Land
Grounding
N (All DVP units should be grounded directly to the ground pole.)
Operation: 0 C ~ 55° C (temperature), 50 ~ 95% (humidity), Pollution degree 2;
°
Environment
Storage: -25 C ~ 70 C (temperature), 5 ~ 95% (humidity)
° °
Vibration/shock
Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
resistance
Weight (g) 124/160 130/120 136/116 225/210
Approvals
I/O Terminal Specification
Input point
Input point type DC
Input type DC (SINK or SOURCE)
Input current 24V DC 5mA
Off O n, above 16.5V DC
Active level →
On O ff, below 8V DC
→
Reaction time About 20ms
Circuit isolation
Photocoupler/LED On
/operation indicator
Output point
Output point type Relay-R
Current specification 1.5A/1point (5A/COM)
Voltage specification Below 250V AC, 30V DC
75VA (inductive)
Maximum load
90W (resistive)
Reaction time About 10ms
Installation and Wiring
ENGLISH
Digital I/O Terminal Wiring
DVP-08HM (8in)
08HM 08HN
X0 X 2 X 4 X 6 Y0 Y1 Y3
S/S X 1 X 3 X 5 X 7
DVP-08HP (4in/4out)
08HP 16HM
X 0 X 2 Y0 Y1 Y 3 S/S X10 X 11
S /S X 1 X3 C0 Y2 S /S
DVP-16HP (8in/8out)
DVP-32HN(32out)
16HP 32HN
(AC Power IN)
S /S X4 X5 X6 X7 Y4 Y5 Y 6 Y 7
X0 X 1 X 2 X3 C 0 Y 0 Y 1 Y2 Y3
Y16
1
C4
S/S X0 X2 X4 X6 X1 0 X12 X14 X16
X1 X3 X5 X7 X11 X13 X15 X1 7
DVP-32HP(16in/16out) DVP-48HP(24in/24out)
32HP 48HP
(AC Power IN,DC Signal IN) (AC Power IN,DC Signal IN)
Y0 Y1 Y3 Y4 Y5 Y7 Y1 0 Y11 Y13 Y1 4 Y1 5 Y17 Y0 Y1
C0 Y2 C1 Y6 C2 Y1 2 C3 Y16 C0
7
Mounting Arrangements and Wiring Notes
3
DIN Rail Installation:
The DVP-PLC can be secured to a cabinet by using the DIN
Height rail that is 35mm high with a depth of 7.5mm. When
mounting the PLC on the DIN rail, be sure to use the end
82
bracket to stop any side-to-side motion of the PLC, thus to
82
reduce the chance of the wires being pulled loose. On the
bottom of the PLC is a small retaining clip. To secure the
82
PLC to the DIN rail, place it onto the rail and gently push up
82
on the clip. To remove it, pull down on the retaining clip and
gently pull the PLC away from the DIN rail. Please see the
figure on the right:
Direct Mounting: Use the specified dimensions and install with M4 screws.
Height
1. Please use O-type or Y-type terminals for I/O wiring terminals. The
82.2
specification for the terminals is as shown on the left. PLC terminal screws
Wiring:
82.2 should be tightened to between 5 ~ 8 kg-cm (4.3 ~ 6.9 in-lbs). Use copper
conductor only, 60° C/75° C.
82.2
2. DO NOT wire to the No Function terminals
Below 6.2
supply should not run through the same multi-wire cable or conduit.
3. When tightening the screws and performing wiring, please avoid that
To suit M3.5 screw terminal
metallic particles fall into PLC. After completing wiring, please remove the
label which is used to obstruct the metallic particles on the ventilation hole
Below 6.2 for well heat dissipation.
4. There should be a 50mm or more distance between the PLC and other
control component. Also, keep the PLC away from high voltage line and
power equipment.
Environment:
DO NOT store the PLC in an airborne dust, smoky, metallic particles, corrosive or flammable gases.
1.
2. DO NOT store the PLC in a location where temperatures and humidity will exceed specification.
3. DO NOT mount the PLC in a location where vibration and shock will exceed specification.
I/O Point Serial Sequence
When connecting MPU with less than 32 points to extension unit, the input number of 1
started from X20 in sequence and the output number is started from Y20 in sequence. If connecting MPU with
more than 32 points to extension unit, the input number of the 1 st
number of the MPU in sequence and the output number is started form the last output number of the MPU in
sequence.
Output unit
Type
Input
PLC Model
points
Relay: 250V AC/30V DC 2A/1point
MPU 16EH/32EH/64EH 8/16/32
EXT1 32HP 16
EXT2 48HP 24
Transistor: 5 ~ 30V DC 0.3A/1 point at 40° C
EXT3 08HP 4
EXT4 08HN 0
In system application example, if the input/output of the 1
as 16 and thus there are no corresponding input/output for higher numbers. The input/output number of
extension number is the sequential number from the last number of the MPU.
Power Input Wiring and Specification
32HP00R/T 48HP00R/T
The power input for DVP-EH series PLC is AC input. Please pay particular attention to the following notes:
1. Connect the AC input (100 ~ 240V) to terminals L and N. Any 110V AC or 220V AC connected to the +24V
100~240V AC (-15%~10%), 50/60Hz ± 5%
terminal or input points will permanently damage the PLC.
30VA 30VA 30VA
2. The AC power inputs for the MPU and the I/O Extension Unit should be ON or OFF at the same time.
NA 500mA 500mA 3. Please use wires of 1.6mm or above for the grounding of the MPU.
4. If the power-cut time is less than 10ms, the PLC still operates unaffectedly. If the power-cut time is too long or
the power voltage drops, the PLC will stop operation and all outputs will be off. Once power is on again, the
PLC will resume automatically. (There are latched auxiliary relays and registers inside of the PLC, please be
aware when programming.)
100~240VAC
AC Input
Type
The +24V supply output is rated at 0.5A as max. from MPU. DO NOT connect external power
supply to this termianl. Moreover, it takes 6 ~ 7mA to drive each input point, so total of 100mA
660/590 438/398 616/576 is needed for 16 input points. As a result, the output load of +24V should not exceed 400mA.
Since the PLC is in control of numerous devices, operation of either one device could affect the operation of
other devices; therefore, the breakdown of either one device would consequently be detrimental to the whole
auto control system, and danger will thus be resulted. Please use the recommended wiring below for the power
input:
5
4
8
Guard
Lim it
MC 3
L N
24 VDC OV
6 6
Transistor-T
55°C 0.1A/1point, 50°C 0.15A/1point,
45° C 0.2A/1point, 40°C 0.3A/1point (2A/COM)
30V DC
Input/Output Point Wiring
9W
Input Point Wiring
Off O n 15us On O ff 25us
There are SINK and SOURCE types for the input signal of the input point with DC input. Definition as follows:
→ →
Sink = Current flow into common terminal S/S
S/S
Sinking
X0
DVP-08HN (8out)
Y4 Y5 Y7 Input point loop equivalent circuit
DC Type
C0 Y2 C1 Y6
(DC Signal IN)
DVP-16HM (16in)
SINK Mode
X12 X13 X 14 X15 X16 X 17
X 0 X1 X2 X 3 X4 X5 X6 X7 (Current flows into the
common terminal S/S)
C0 Y1 C1 Y4 C2 Y7 Y11 C3 X14
Y2 Y3 Y5 Y6 Y10 Y12 X15
Input point loop equivalent circuit
DC Type
Y21 Y22 Y23 Y25 Y26 Y27 Y31 Y32 Y34 Y36
(DC Signal IN)
Y20 C5 Y24 C6 Y30 C7 Y33 Y35 Y37
X22
S/S X0 X2 X4 X6 X10 X12 X14 X16 X20 X24 X26
X1 X3 X5 X7 X11 X13 X15 X17 X21 X23 X25 X27
SOURCE Mode
(Current flows out of
common terminal S/S)
Y3 Y4 Y5 Y7 Y10 Y11 Y13 Y14 Y15 Y17 Y20 Y22 Y24 Y26
Y2 C1 Y6 C2 Y12 C3 Y16 C4 Y21 Y23 Y25 Y27
Output Point Wiring
For heat dissipation. Make
sure to provide a minimum Relay output wiring
clearance of 50mm between
the unit and all sides of the
cabinet. (shown as below)
C0 Y0 C1 Y1 C2
MC2
2
5 2
8
> 5 0 mm
9 3 7
D V P MP U
> 5 0mm > 5 0 mm
5
> 5 0 mm
10
*1: There is no protection circuit for the Relay output in the PLC. If DC conductive loading is on, add a diode in reverse direction in
parallel to extend the life of the Relay. The diode in reverse direction should correspond to the following specification:
. I/O signal wires or power
• - The diode is able to withstand 5~10+ times loading voltage as maximum.
- The forward current of the diode must be greater than loading current.
*2: Use external hardware interlock and those in the PLC program to secure any emergent errors with safety protection.
*3: There is no protection circuit for the Relay in the PLC. If AC conductive loading is on, connect a surge absorber (0.1uF+ "100ohm to
120ohm") to reduce interference and extend the life of the Relay.
Transistor output wiring
C0 Y0 C1 Y1 C2
MC2
6
5 7 8
3
2
3
st extension unit is
extension unit is started from the last input
*1: Use external hardware interlock and those in the PLC program to secure any emergent errors with safety protection.
*2: Use Zener diode (39V) inside the PLC to protect the transistor. If conductive loading is on, adding a diode in reverse direction in
parallel is recommended.
MP U EXT1 EXT2 EXT3 EXT4
Output
Input number Output number
points
8/16/32 X0~X7/X0~X17/X0~X37 Y0~Y7/Y0~Y17/Y0~Y37
16 X20~X37/X20~X37/X40~X57 Y20~Y37/Y20~Y37/Y40~Y57
24 X40~X67/X40~X67/X60~X107 Y40~Y67/Y40~Y67/Y60~Y107
4 X70~X73/X70~X73/X110~X113 Y70~Y73/Y70~Y73/Y110~Y113
8 - Y74~Y103/Y74~Y103/Y114~Y123
st
MPU are less than 16, its input/output will be defined
產 品 外 觀 及 各 部 介 紹
L N +24V 24G S/S X0 X1 X2
2.0 A
DC/DC +5V
Power supply for AC loads
1.
Fuse for circuit protection (3A limit)
2.
Power on pilot indicator
3. DIN
1
Emergency stop: a manual stop button is provided for emergency
4. DIN
to disconnect system power.
2
機 種 型 號
Circuit isolation device (System Power Disconnect): use
electromagnetic contactor and the relay to be the isolation unit of
MC
the power circuit to prevent the possible instability of the system
1
when the power is supplied on and off.
DVP PLC MPU (main processing unit)
7
Class three grounding.
Power supply:
AC: 100 ~ 240V AC, 50/60Hz
DC: 24V DC
Source = Current flows out of common terminal S/S
X0
S/S
Sourcing
Wiring loop
SINK
+24V
24VDC +5V
24G
S/S
+24V 24G S/S X0 X1 X2
X0
Sink Type
電 氣 規 格
Wiring loop
SOURCE
+24V
24VDC +5V
24G
S/S
+24V 24G S/S X0 X1 X2
X0
Source Type
24V DC
24V DC
DO NOT wire to the No Function terminals •
Fuse
Diode in reverse direction to protect the relay*1
Y2 Y3 Y4 Y5 Mutually exclusive outputs*2
1
MC1
Emergency stop: use an external switch
Surge absorber*3
MC1 MC2 7
6 Conductive loading
4
Incandescent lamp (resistive loading)
DC supply
AC supply
輸 入
DO NOT wire to the No Function terminals
•
Emergency stop
Fuse
Y2 Y4 Y5
Y3
Mutually exclusive output*1
1
MC1
DC apply
Incandescent lamp (resistive loading)
MC1 MC2
6
Diode in reverse direction to protect the transistor*2
4
9
Conductive loading
Resistive loading
注 意 事 項
(OPEN TYPE)
( : )
/
產 品 簡 介
DVP-EH EH 8 ~ 48 /
5 2 2
5 7 5
7 1
5
4
1
4
3 3
7
3
(mm)
DVP08HM11N 90 40 82
DVP16HM11N 90 55 82
DVP08HN11R/T 90 40 82
DVP16HP11R/T 90 55 82
6
7 9 2 8 6 6
1
(mm)
(w)
4
10 DVP32HN00R/T 90 143.5
11
DVP32HP00R/T 90 143.5
3
DVP48HP00R/T 90 174
3 3
7
5. 9.
/ 10.
6.
7. 11.
8.
DVP08HM11N 8 0
DVP16HM11N 16 0
DVP08HN11R 0 8
DVP08HP11R 4 4 Relay 250V AC/30V DC 2A/1
DC Type
24V DC
Sink/Source
DVP16HP11R 8 8
DVP08HN11T 0 8
Transistor 5 ~ 30V DC 0.3A/1
DVP08HP11T 4 4
@40°C
DVP16HP11T 8 8
DVP32HN00R 0 32
DVP32HP00R 16 16 Relay 250V AC/30V DC 2A/1
DVP48HP00R 24 DC Type 24
100 ~ 240V
DVP32HN00T AC 0 Sink/Source 32
Transistor 5 ~ 30V DC 0.3A/1
DVP32HP00T 16 16
@40 C
DVP48HP00T 24 24
規 格
08HM11N
08HN11R/T 08HP11R/T 16HP11R/T 32HN00R/T 32HP00R/T 48HP00R/T
16HM11N
100 ~ 240V AC (-15% ~ 10%),
24V DC (20.4V DC ~ 28.8V DC) (-15% ~ 20%)
50/60Hz ± 5%
1W / 1.5W 1.5W 1.5W 2W 30VA 30 VA
NA NA NA NA NA 500 mA
24V DC
1,500V AC (Primary-secondary), 1,500V AC (Primary-PE), 500V AC (Secondary-PE)
5 M / 500V DC
ESD: 8KV Air Discharge, EFT: Power Line: 2KV, Digital I/O: 1KV, Analog &
Communication I/O: 250V,
Digital I/O: 1KV, RS: 26MHz ~ 1GHz, 10V/m
L, N PLC
0 ~ 55°C 50 ~ 95% 2
/
-25 ~ 70°C 5 ~ 95%
/ IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
(g) 124/160 130/120 136/116 225/210 660/590 438/398
/ 出 點 規 格
SINK SOURCE
24V DC 5mA
Off → On 16.5V DC
On → Off 8V DC
20ms
/ /LED On
-R -T
55°C 0.1A/1 50°C 0.15A/1
1.5A/1 5A/COM
45°C 0.2A/1 40°C 0.3A/1
250V AC,30V DC 30V DC
75VA
9W
90 W
10 ms Off → On 15us On → Off 25us
繁 體 中 文
/
256
7
3
82.2
82.2
82.2
30 VA
500 mA
616/576
2A/COM