Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
2
Print only the pages for your vehicle using the advanced
options in the Print menu.
3
Install your Maestro RR according to the guide for your vehicle.
Pressing the printer icon or "quick printing" this document will print
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in
Page 1
Print only the pages for your vehicle using the advanced options in the Print menu. Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.
Buick EnclavE RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 3
Buick EnclavE 2008-2017 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 5
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 9
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 10
Buick lucErnE RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 11
Buick lucErnE 2006-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 13
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 17
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 19
2006-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 21
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 25
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 26
EScaladE RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 27
EScaladE 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 29
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 33
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 34
WiTH NaV RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 35
EScaladE WiTH nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 37
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 41
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 42
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 43
EScaladE WiTHouT nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 45
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 49
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 51
2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 53
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 57
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 58
WIth nAv RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 59
WiTH nav 2012-2013 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 61
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 65
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 66
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 67
WiTHouT nav 2012-2013 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 69
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 73
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Equinox RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 75
Equinox 2007-2009 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 77
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 81
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 82
WIth NAv RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 83
ExprESS WiTH nav 2013-2019 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 85
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 89
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 90
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 91
ExprESS WiTHouT nav 2008-2019 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 93
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 97
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 99
2006-2013 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 101
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 105
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 107
2014-2016 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 109
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 113
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 114
RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 115
2006-2007 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 117
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 121
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 122
SilvErado 1500 RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 123
SilvErado 1500 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 125
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 129
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 130
With Nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 131
SilvErado 1500 WiTH nav 2012-2013 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 133
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 137
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 138
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 139
SilvErado 1500 WiTHouT nav 2012-2013 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 141
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 145
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
SilvErado 2500 & 3500 RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 147
SilvErado 2500 & 3500 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 149
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 153
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 154
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 155
SilvErado 2500 & 3500 WiTHouT nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 157
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 161
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 162
With Nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 163
SilvErado 2500 WiTH nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 165
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 169
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
SuBurBan RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 171
SuBurBan 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 173
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 177
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 178
WIth nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 179
SuBurBan WiTH nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 181
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 185
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 186
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 187
SuBurBan WiTHouT nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 189
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 193
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
TaHoE RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 195
TaHoE 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 197
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 201
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 202
WIth Nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 203
TaHoE WiTH nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 205
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 209
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 210
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 211
TaHoE WiTHouT nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 213
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 217
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
TravErSE RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 219
TravErSE 2009-2017 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 221
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 225
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 226
Gmc acadia RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 227
Gmc acadia 2007-2016 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 229
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 233
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 234
WITH nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 235
Gmc Savana WiTH nav 2013-2019 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 237
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 241
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 242
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 243
Gmc Savana WiTHouT nav 2008-2019 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 245
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 249
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Gmc SiErra 1500 RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 251
Gmc SiErra 1500 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 253
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 257
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 258
WiTH NaV RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 259
Gmc SiErra 1500 WiTH nav 2012-2013 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 261
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 265
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 266
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 267
Gmc SiErra 1500 WiTHouT nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 269
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 273
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Gmc SiErra 2500 & 3500 RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 275
Gmc SiErra 2500 & 3500 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 277
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 281
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 282
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 283
Gmc SiErra 2500 & 3500 WiTHouT nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 285
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 289
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 290
WiTH NaV RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 291
Gmc SiErra 2500 WiTH nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 293
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 297
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Gmc Yukon RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 299
Gmc Yukon 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 301
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 305
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 306
WITH nAV RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 307
Gmc Yukon WiTH nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 309
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 313
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 314
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 315
Gmc Yukon WiTHouT nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 317
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 321
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Gmc Yukon xl RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 323
Gmc Yukon xl 2007-2011 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 325
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 329
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 330
WITH nAV RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM2 Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 331
Gmc Yukon xl WiTH nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 333
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 337
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 338
WiTHouT nav RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 339
Gmc Yukon xl WiTHouT nav 2012-2014 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi...
Page 341
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 345
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
HummEr H2 RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 347
HummEr H2 2008-2009 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 349
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 353
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Page 354
SaTurn ouTlook RETAINS STEERING WHEEL CONTROLS, ONSTAR, BLUETOOTH, XM SATELLITE AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro GM5+ Installation Harness Radar Installation Guides E L E C T R O N I C S...
Page 355
SaTurn ouTlook 2007-2010 WELCOME TABLE OF CONTENTS Before Installing Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are Installation Instructions now a few simple steps away from enjoying your new car radio with Wiring Diagram with an Amplifi er enhanced features.
Page 357
• Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX).
Page 361
The light on the Maestro is blinking Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty. TWICE Make sure the correct radio model and serial number were entered during the fl...
Need help?
Do you have a question about the Maestro RR and is the answer not in the manual?
Questions and answers