Download Print this page

Advertisement

Quick Links

・This document contains descriptions of how to set the new functions and their restrictions.
Refer also to the Operating Instructions of this product.
・Depending on the model used, the screens shown in the explanations may differ to the
actual camera screens.
・This document is for the following models.
WV-S1572L, WV-S2572L, WV-S2272L, WV-S1552L, WV-S2552L, WV-S2252L
・Firmware Ver.1.50
No.
1
Add a notify to the [SNMP trap setting]
2
Add to the system log when recording stream fails to
write
3
Add a function to notify the user of writing failures in the
recording stream with a unique alarm
4
Add a note when the bit rate of the recording stream is
set to a value exceeding recommended value
5
Extend authentication password for the destination of
notification
・Firmware Ver.1.51
No.
6
Add LLDP function
・Firmware Ver.1.60
No.
7
Add SFTP periodic image transmission to "Event
operation" of Easy Setup
8
Add "SFTP periodic image transmission error" to "Save
mode" of SD memory card
9
Add a link to SFTP settings in camera action on alarm
10
Add SFTP image transmission function
11
Add SFTP periodic image transmission to "Operation
mode" of schedule
12
Change the initial value of "Overwrite" of SD memory
card to On
13
Add the supplementary explanation of On/Off of Internet
mode to the setting screen
14
Add NTP test function
New functions and addendum
Functions
Functions
Functions
Advanced (Network)
Maintenance (Status)
Notification (Alarm)
Image/Audio (Image)
Network (Advanced)
Advanced (Network)
Event action (Easy Setup)
SD memory card (Basic)
Alarm
Advanced (Network)
Schedule
SD memory card (Basic)
Advanced (Network)
Advanced (Network)
1
Item (Page)
Item (Page)
Item (Page)
Page
3
4
5
6
7
Page
8
Page
10
18
19
22
27
29
30
31

Advertisement

loading
Need help?

Need help?

Do you have a question about the WV-S1572L and is the answer not in the manual?

Questions and answers

Summary of Contents for Panasonic WV-S1572L

  • Page 1 Refer also to the Operating Instructions of this product. ・Depending on the model used, the screens shown in the explanations may differ to the actual camera screens. ・This document is for the following models. WV-S1572L, WV-S2572L, WV-S2272L, WV-S1552L, WV-S2552L, WV-S2252L ・Firmware Ver.1.50 Functions Item (Page)
  • Page 2 Add TLS settings to HTTPS Advanced (Network) Add MQTT function Advanced (Network) Add a system log when MQTT function fails Status (Maintenance)
  • Page 3 1. Add a notify to the [SNMP trap setting] (Operating Instructions Configure the network settings [Network] - Configure advanced network settings [Advanced]) Add the notifications to [SNMP trap settings]. Note • In order to activate SNMP trap notifications for when alarms occur, alarm operation settings are required.
  • Page 4 2. Add to the system log when recording stream fails to write (Operating Instructions “Others” – “Maintenance” - Check the status [Status]) A system log has been added for errors in the write process of the recording stream to the log related to SD memory cards.
  • Page 5 -Configuration of the settings relating to alarm notification[Notification]- Configure the settings relating to Panasonic alarm protocol) Add the write processing error of the recording stream to the occurrence condition of the Panasonic alarm protocol notification of “Diag.” Panasonic alarm protocol •...
  • Page 6 4. Add a note when the bit rate of the recording stream is set to a value exceeding recommended value (Operating Instructions “Image/Audio” - Configure the settings relating to Stream [Image] Add the statement that it is possible that an error may occur in the continuity of SD memory card recording, if you set a bit rate that exceeds the recommended value in “Note”...
  • Page 7 5.Extend authentication password for the destination of notification (Operating Instructions – Configure the network settings [Network] – Configure advanced network settings [Advanced] - Configure the settings related to sending E-mails) The number of characters that can be entered for the authentication password of the destination of notification has been expanded to 128 characters.
  • Page 8 6. Add LLDP function (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced]) LLDP (Link Layer Discovery Protocol) has been added to [Advanced] of [Network]. Interoperability can be achieved by sending and receiving camera's device information to and from LLDP-compatible devices.
  • Page 9 Available characters: Alphanumeric characters Default: None (blank) Note • Click the [Set] button to restart the product. After restarting, the product cannot be operated for about 2 minutes, just like when the power is turned on. • For information about devices that can be connected using Fabric Attach, refer to our support website. https://i-pro.com/global/en/surveillance/training-support/support/technical-information...
  • Page 10 7. Add SFTP periodic image transmission to “Event operation” of Easy Setup (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action]) With the addition of the SFTP function, SFTP periodic image transmission has been added to the “Event action”...
  • Page 11 Flow of event action setup Schedule Event function type: Alarm → Schedule: Configure SD Select the trigger (→Alarm: Configure the terminal recording or SFTP periodic image according to the and VMD (alarm setup menu)) transmission (schedule function purpose of setting. type setup menu)) Terminal/VMD/SCD...
  • Page 12 Configure the schedule/alarm (event function type setup menu) (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action] – Configure the schedule/alarm (event function type setup menu)) Here, select the function type of the event. [Trigger] •...
  • Page 13 Alarm: Configure the alarm function type (Alarm function type setup menu) (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action] – Alarm: Configure the alarm function type (Alarm function type setup menu)) Select the alarm function type as “SFTP transfer” or “SD memory recording”. Configure “Recording format”...
  • Page 14 Alarm: Configure the details for image transfer or recording conditions (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action] – Alarm: Configure the details for recording conditions) Set SFTP transfer (SFTP transfer setup menu) SFTP transfer when an alarm is detected is set in this section.
  • Page 15 Schedule: Configure SD recording or SFTP periodic image transmission (schedule function type setup menu) (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action] – Schedule: Configure SD recording or SFTP periodic image transmission (schedule function type setup menu) ) Here, the schedule type is selected as “SD memory recording”...
  • Page 16 Schedule: Configure SFTP periodic image transmission (SFTP periodic image transmission setup menu) (Operating Instructions – Use Easy Setup [Easy Setup] – Configure an event action [Event action]) The SFTP periodic image transmission is configured in this section. • To configure SFTP periodic image transmission settings: Refer to “10.
  • Page 17 •To configure SFTP periodic image transmission schedule settings: Refer to “Configure the settings relating to the schedules [Schedule]” for information about how to set the above screen. [Set] button If you click the [Set] button, setup will be completed. [Back] button If you click the [Back] button, the SFTP periodic image transmission setup menu will be displayed.
  • Page 18 8. Add “SFTP periodic image transmission error” to “Save trigger” of SD memory card (Operating Instructions – Configure the basic settings of the camera [Basic] – Configure the settings relating to the SD memory card [SD memory card]) With the addition of the SFTP function, “SFTP periodic image transmission error” has been added to the “Save trigger”...
  • Page 19 9. Add link to SFTP settings in Camera action on alarm (Operating Instructions – Configure the alarm settings [Alarm] – Configure the settings relating to the camera action on alarm occurrence [Alarm]) Click the [Alarm] tab on the “Alarm” page. (→“How to display the setup menu”, “How to operate the setup menu”) The settings related to the camera action on alarm can be configured in this section.
  • Page 20 [SNMP transmission upon alarm detection] Click “To SNMP setting” to display the setup menu that can configure the settings relating to SNMP transmission when an alarm occurs. The setup menu will be displayed in a newly opened window. (→“Configure settings relating to SNMP transmissions of alarm images”)
  • Page 21 Configure settings relating to SFTP transmissions of alarm Images (Operating Instructions – Configure the alarm settings [Alarm] – Configure the settings relating to the camera action on alarm occurrence [Alarm]) Click “SFTP setup >>” of “Camera action on alarm” on the [Alarm] tab of the “Alarm” page. (→”Configure the settings relating to the camera action on alarm occurrence [Alarm]”) Refer to “10.
  • Page 22 10. Add SFTP image transmission function (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced]) SFTP (SSH File Transfer Protocol) function has been added to securely send images to the server by using SSH (Secure Shell) encrypted data stream. It has the following two transmission functions.
  • Page 23 • Available number of characters: 1 - 256 characters • Unavailable characters: " & ; [File name] Enter the file name used for the alarm image to be transmitted to an SFTP server. The file name will be as follows. File name: [“Entered file name”...
  • Page 24 Image quality 1280x960 Image 1280x720 capture 800x600 size 640x360 400x300 QVGA 320x180 [Post alarm] • Transmission interval Select the transmission interval for the alarm image transmission to the FTP server from the following. When 30fps mode is selected for [Image capture mode]: 0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps When 25fps mode is selected for [Image capture mode]: 0.08fps/ 0.17fps/ 0.28fps/ 0.42fps/ 1fps •...
  • Page 25 [Directory name] Enter the directory name where the images are to be saved. For example, enter “/img” to designate the directory “img” under the root directory of the SFTP server. • Available number of characters: 1 - 256 characters • Unavailable characters: " & ; •...
  • Page 26 [Port number] Enter a control port number to be used for the FTP server. • Available port number: 1-65535 • Default: 22 The following port numbers are unavailable since they are already in use. 20, 23, 25, 42, 53, 67, 68, 69, 80, 110, 123, 161, 162, 443, 995, 10669, 10670 [Host key hash] Enter the hash value of the public key of the SFTP server.
  • Page 27 11. Add SFTP periodic image transmission to “Schedule mode” of Schedule (Operating Instructions – Configure the settings relating to the schedules [Schedule]) “SFTP periodic image transmission” was added to “Schedule mode” of the schedule setting. [Schedule mode] Select an action to be assigned to the schedule from “Schedule mode”. “Off”...
  • Page 28 Note • Select “On” for “User auth.” on the [User auth.] tab of “User mng.” page (→“Configure the settings relating to the user authentication [User auth.]”) and “Off” for “Host auth.” on the “Host auth.” page (→“Configure the settings relating to the host authentication [Host auth.]”) to validate “Access permission”.
  • Page 29 12. Change the initial value of “Overwrite” of SD memory card to On (Operating Instructions – Configure the basic settings of the camera [Basic]) – Configure the settings relating to the SD memory card [SD memory card]) [Overwrite] Determine whether or not to overwrite when the remaining capacity of the SD memory card becomes insufficient.
  • Page 30 13. Add the supplementary explanation of On/Off of Internet mode to the setting screen (Operating Instructions – Configure the settings relating to images and audio [Image/Audio] – Configure the settings relating to Stream [Image]) Add the supplementary explanation of On/Off of Internet mode setting. [Internet mode] Select “On”...
  • Page 31 14. Add NTP test function (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced] – Configure the settings relating to the NTP server) Add a test function for time synchronization to check if it can communicate with NTP server. [NTP test] Select “Synchronization with NTP server”...
  • Page 32 15. Add TLS settings to HTTPS (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced] – Configure the HTTPS settings) Add TLS1.1, TLS1.2 and TLS1.3 selection items to the HTTPS connection method. [HTTPS - Connection] Select the protocol used to connect the camera.
  • Page 33 16. Add MQTT function (Operating Instructions – Configuring the network settings [Network] – Configure advanced network settings [Advanced]) MQTT (Message Queueing Telemetry Transport) has been added to “Advanced” of “Network”. When an alarm occurs, the MQTT server can be notified of the event action by the alarm. [MQTT settings] Set On/Off whether to enable/disable the MQTT function.
  • Page 34 [Port] Enter the port number of the MQTT server. Available port number: 1 - 65535 Default: 8883 The following port numbers cannot be set because they are used by this product. 20, 21, 23, 25, 42, 53, 67, 68, 69, 80, 110, 123, 161, 162, 443, 554, 995, 10669, 10670 [Protocol] Select the protocol to use when connecting to an MQTT server from MQTT over SSL/MQTT over TCP.
  • Page 35 Notification setting [Alarm] Check the alarm events to be notified to the MQTT server. Terminal 1: Notifies the MQTT server when an alarm occurs at terminal 1. Terminal 2: Notifies the MQTT server when an alarm occurs at terminal 2. Terminal 3: Notifies the MQTT server when an alarm occurs at terminal 3.
  • Page 36 17. Add a system log when MQTT function fails (Operating Instructions – Others – About the displayed system log) Add a system log when an error occurs in the MQTT function. Error display related to MQTT Category Indication Description When the connection to the server fails, MQTT <MQTT>...

This manual is also suitable for:

Wv-s2572lWv-s2272lWv-s1552lWv-s2552lWv-s2252l