RTL8852CE User’s Manual Warning Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 5
RTL8852CE User’s Manual Operations in the 5.15-5.25GHz band are restricted to indoor usage only. FCC regulations restrict the frequency 5850-5895MHz operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet.
Page 6
RTL8852CE User’s Manual 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules.
Page 7
RTL8852CE User’s Manual reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Page 8
RTL8852CE User’s Manual minimum separation distance 5 mm from the users. Any separation distances less than 5mm will require additional evaluation and FCC/ISED authorization. Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6317A-RTL8852CE ".
Page 10
RTL8852CE User’s Manual Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
Page 11
Le présent émetteur radio [IC: 6317A-RTL8852CE] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal.
RTL8852CE User’s Manual Informations sur l'exposition aux RF (SAR) Cet appareil a été testé à une distance de séparation de 5 mm et respecte les limites applicables pour l'exposition aux radiofréquences (RF). Pour garantir la conformité de l'exposition RF, la ou les antennes utilisées avec l'appareil doivent être installées sur des plates-formes hôtes offrant une distance de séparation minimale de 5 mm...
RTL8852CE User’s Manual CE/UK Statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The frequency and the maximum transmitted power in EU are listed below: 2412-2472MHz: ≤...
Page 14
RTL8852CE User’s Manual Installing the Wireless PCIe NGFF2230 module Hardware Installing PCIe NGFF2230 module to PCIe NGFF2230 connector and connect two external Wi-Fi antennas on I-PEX connectors.
Page 15
RTL8852CE User’s Manual Un-installing the Wireless PCIe NGFF2230 module Hardware Remove 2 external Wi-Fi Antennas from the Wireless PCIe NGFF2230 module board and remove the Wireless PCIe NGFF2230 module board from PCIe NGFF2230 connector port...
Page 16
RTL8852CE User’s Manual Installing the WLAN PCIe & Bluetooth USB NGFF2230 module Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7. Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first.
Page 17
RTL8852CE User’s Manual C. Click “Next” button. D. Select “Complete” and click “Next” button.
Page 18
RTL8852CE User’s Manual E. Click “Install” button.
Page 19
RTL8852CE User’s Manual F. Click “Finish” button. G. Please click “下一步”to continue.
Page 20
RTL8852CE User’s Manual H. Please click “下一步”to continue. I. Please click “安装”to start installation.
Page 21
RTL8852CE User’s Manual J. Please click “完成”to finish the installation.
Page 22
Un-installing the Wireless PCIe NGFF2230 module Software A. Uninstall the RTL8852CE WLAN Driver from “Start”→ “Control Panel”→ “Programs” Please select items as below and click “Uninstall” to remove RTL8852CE WLAN, BT driver and MP UI.
Need help?
Do you have a question about the RTL8852CE and is the answer not in the manual?
Questions and answers