Subscribe to Our Youtube Channel
Related Manuals for Realtek RTL8852AE
Summary of Contents for Realtek RTL8852AE
- Page 1 RTL8852AE User’s Manual (Realtek RTL8852AE) 11ax RTL8852AE Combo module Module User’s Manual Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com...
-
Page 2: Table Of Contents
RTL8852AE User’s Manual ONTENT ENVIRONMENTAL .......................... 3 WARNING ............................4 Federal Communication Commission Interference Statement ...... 4 ......................8 NDUSTRY ANADA TATEMENT NCC 警語 ...................... 8... -
Page 3: Environmental
RTL8852AE User’s Manual ENVIRONMENTAL Parameter Minimum Maximum Units °C Storage Temperature +125 °C Ambient Operating Temperature °C Junction Temperature... -
Page 4: Warning
RTL8852AE User’s Manual Warning Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 5 RTL8852AE User’s Manual This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. The SAR test is according to KDB 616217 for test requirements.” The maximum output power is reduced by software to perform SAR evaluation as application.
- Page 6 RTL8852AE User’s Manual 2.5 Trace antenna designs Not applicable. 2.6 RF exposure considerations This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator &...
- Page 7 RTL8852AE User’s Manual 2.8 Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: ”. The grantee's FCC ID can be used TX2-RTL8852AE only when all FCC compliance requirements are met.
-
Page 8: Industry Canada Statement
RTL8852AE User’s Manual OEM/Host manufacturer responsibilities OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. - Page 9 RTL8852AE User’s Manual function is available. The SAR evaluation is according to KDB 616217, and the module approach distance restriction is 5 mm for notebook, 10 mm for tablet. Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé.
- Page 10 The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: “Contains IC: 6317A-RTL8852AE”. Plaque signalétique du produit final...
- Page 11 Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6317A-RTL8852AE ". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end...
- Page 12 Le présent émetteur radio (IC: 6317A-RTL8852AE / Model: RTL8852AE) a été approuvé par ISED pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal.
- Page 13 RTL8852AE User’s Manual (dBi) (GHz) 2.4~2.5 Chain 0 LYNwave ALA110-222050-300011 PIFA i-pex(MHF) 5.15~5.85 2.4~2.5 Chain 1 LYNwave ALA110-222050-300011 PIFA i-pex(MHF) 5.15~5.85 3.14 2.4~2.5 Chain 0 RFDPA171320EMLB301 Dipole i-pex(MHF) 5.15~5.85 3.14 2.4~2.5 Chain 1 RFDPA171320EMLB301 Dipole i-pex(MHF) 5.15~5.85 For SAR (Portable)
- Page 14 RTL8852AE User’s Manual 2. 系統廠商應於平台上標示「本產品內含射頻模組： XXXyyyLPDzzzz-x」字樣。 Japan Statement Host system must be labeled with "Contains MIC ID:xxxxxx“, MIC ID displayed on label. Installing the Wireless PCIe NGFF2230 module Hardware Installing PCIe NGFF2230 module to PCIe NGFF2230 connector and connect two...
- Page 15 RTL8852AE User’s Manual Un-installing the Wireless PCIe NGFF2230 module Hardware Remove 2 external Wi-Fi Antennas from the Wireless PCIe NGFF2230 module board and remove the Wireless PCIe NGFF2230 module board from PCIe NGFF2230 connector port...
- Page 16 RTL8852AE User’s Manual Installing the WLAN PCIe & Bluetooth USB NGFF2230 module Software Before you proceed with the installation, please notice following descriptions. Note1: The following installation was operated under Windows 7. Note2: If you have installed the WLAN driver & utility before, please uninstall the old version first.
- Page 17 RTL8852AE User’s Manual B. Select ”I accept the terms in license agreement” and click “Next” to process the installation C. Click “Next” button.
- Page 18 RTL8852AE User’s Manual D. Select “Complete” and click “Next” button.
- Page 19 RTL8852AE User’s Manual E. Click “Install” button. F. Click “Finish” button.
- Page 20 RTL8852AE User’s Manual G. Please click “Next”to continue. H. Please click “Next”to continue.
- Page 21 RTL8852AE User’s Manual I. Please click “Install”to start installation. J. Please click “finish”to finish the installation.
- Page 22 Un-installing the Wireless PCIe NGFF2230 module Software A. Uninstall the RTL8852AE WLAN Driver from “Start”→ “Control Panel”→ “Programs” Please select items as below and click “Uninstall” to remove RTL8852AE WLAN, BT driver and MP UI.
Need help?
Do you have a question about the RTL8852AE and is the answer not in the manual?
Questions and answers