Gigabyte MB10-DS Series Quick Reference Manual

2 3 4
35
34
33
32
30
29
31
28 27 26 25
23
ATX Power/ 电源
No. Pin Define No. Pin Define
1
1 3.3V 13 3.3V
1
2 3.3V 14 -12V
13
3 GND 15 GND
4 +5V 16 PS_ON
5 GND 17 GND
5
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 -5V
9 5VSB 21 +5V
24
10 +12V 22 +5V
12
11 +12V 23 +5V
12 3.3V 24 GND
No. Pin Define No. Pin Define
3
4 8
1 GND 5 +12V
2 GND 6 +12V
3 GND 7 +12V
4 GND 8 +12V
1 5
Front Panel Header/ 前面板
No. Pin Define No. Pin Define
1 Power LED+ 2 5V Standby
24 23
4 ID LED+
3 No Pin
6 ID LED-
5 Power LED-
8 System Status LED+
7 HDD LED+
10 System Status LED-
9 HDD LED-
12 LAN1 Active LED+
11 Power Button
14 LAN1 Link LED-
13 GND
16 SMBus Data
15 Reset Button+
18 SMBus Clock
17 GND
2 1
20 Case Open
19 ID Switch+
22 LAN2 Active LED
21 ID Switch-
24 LAN2 Link LED-
23 NMI Switch-
SATA Connector/SATA BMC F/W Readiness LED
接口
7
BMC Firmware Readiness LED (LED_BMC1):
No. Pin Define No. Pin Define
State Description
1 GND 5 RXN
On BMC firmware is initial
2 TXP 6 RXP
Blink BMC firmware is ready
3 TXN 7 GND
Off AC loss
4 GND
1
SATA SGPIO Header/ GPIO SATA DOM Power Cable Connector
串行
No. Pin Define No. Pin Define
1 SDIN 4 SLOAD
3 1
1 5
2 GND 5 SCLK
3 SDOUT
12QM1-MB10D0-00R
Проконсультироваться и купить данное оборудование вы можете в компании «АНД-Системс»
адрес: 125480, г.Москва, ул.Туристская, д.33/1; site: https://andpro.ru тел: +7 (495) 545-4870 email: info@andpro.ru
MB10-DS Series Quick Reference Guide/ 快速测试参考指南
5 6 7 8 9
10
16 15 14 13
1
12
17
24
19 18
22 21 20
PMBUS
TPM Connector/
可信平台模块
2 14
No. Pin Define
1 13
1 PMBus Clock
2 PMBus Data
No. Pin Define
3 PMBus Alert
1 CLK
4 GND
2 P_3V3_AUX
5 3.3V Sense
3 LPC_RST
4 P3V3
5 LPC_LAD0
IPMB
6 IRQ_SERIAL
7 LPC_LAD1
8 No Connect
9 LPC_LAD2
No. Pin Define
10 No Connect
1 Clock
1
11 LPC_LAD3
2 GND
12 GND
3 Data
13 LPC_FRAME_N
14 GND
HDD Back Plane Board Header/
硬盤背板排針
26 1
25 2
No. Pin Define No. Pin Define
1 BP_SGP_CLK 2 No Connect
4 FAN_SGP_GLD
3 BP_SGP_GLD
6 GND
5 BP_SGP_DOUT
8 Reset
7 Key Pin
9 GND 10 BP_LED_A_N
12 GND
11 BP_LED_G_N
14 No Connect
13 BP_SGP_DIN
16 SMB_BP_DATA
15 GND
18 SMB_BP_CLK
17 GND
20 BMC_ACK
19 P_3V3_AUX
22 BMC_REQ
21 P_3V3_AUX
24 Key Pin
23 GND
25 BP_PRESENSE 26 GND
Serial Port Cable Connector/ 串行端口
No. Pin Define
1 2
1 NDCD-
2 NSIN
3 NSOUT
4 NDTR-
5 GND
9 10
6 NDSR-
7 NRTS-
8 NCTS-
9 NRI-
No. Pin Define
10 No Pin
1 P5V
2 GND
3 NC
При обращении используйте промокод AND-PDF и получите скидку.
No. Code Description
1 CPU Intel Xeon® processor D-1541, FCBGA1667 SoC (MB10-DS0/3)
Intel Xeon® processor D-1521, FCBGA1667 SoC (MB10-DS1/4)
Intel Xeon® processor D-1581, FCBGA1667 SoC (MB10-DS2/5)
2 SFP+1_2 SFP+ LAN connectors#1/#2
3 LAN1_2 LAN ports
4 USB3_MLAN BMC Management LAN port (top) / USB 3.0 ports (bottom)
5 CPU0_FAN CPU fan connector
6 VGA VGA port
7 SW_ID ID switch button w/LED
8 SW_PWR Power button w/LED
9 LED_STA System Status LED
10 P12V_AUX2 8 pin power connector
11 FP_1 Front panel header
12 ATX1 24 pin main power connector
13 DIMM_P0_A0 Channel 1 slot 0
14 DIMM_P0_A1 Channel 2 slot 1
15 DIMM_P0_B0 Channel 3 slot 0
16 DIMM_P0_B1 Channel 4 slot 1
17 BAT1 Battery
18 PMBUS PMBus connector
19 SATA_DOM0 SATA DOM power cable connector
11
6
4
1
5
2 3
No. Desription
1 System Status LED
2 Power button w/LED
3 ID switch button w/LED
4 VGA port
5 USB 3.0 ports
6 KVM Server Management 10/100/1000 LAN Port (Dedicated LAN Port)
7 LAN ports
8 SFP+ LAN ports (MB10-DS3/MB10-DS4/MB10-DS5)
CPU/System FAN/
风扇
4
4 1
1
No. Pin Define
1 GND
2 +12V
3 Sense
4 Speed Control
4
3
2
1
No. Code Description
20 SATA0 SATA 3 6Gb/s connector
21 SATA1 SATA 3 6Gb/s connector
22 SATA_2_3 SATA 3 6Gb/s connectors
23 SATA_4_5 SATA 3 6Gb/s connectors
24 SATA_SGPIO SATA SGPIO header
25 SYS_FAN 2 System fan connector#2
26 COM1 Serial port cable connector
27 LED_BMC1 BMC firmware readiness LED
28 BP_1 HDD back plane board header
29 TPM TPM module connector
30 IPMB IPMB connector
31 CLR_CMOS Clear CMOS jumper
32 PCIE_1 PCI Express x16 slot
33 ME_UPDATE ME update jumper
34 ME_RCVR ME recovry jumper
35 S3_MASK S3 Power On Select jumper
Rear I/O Connector/ 后面板接口
10/100/1000 LAN LED:
7 8
State
Yellow On 1Gbps data arte
Speed LED Link/Activity
LED
Green On 100Mbps data arte
Off 10Mbps data arte
Speed LED Link/Activity
LED
SFP+ LAN LED:
State
Yellow On 1Gbps data rate
Green On 10 Gbps data rate
Memory Population Configuration/ 安装内存
Ranks PerDIMM
Type and
Data Width
SRx4 ECC
RDIMM
RDIMM
SRx8 ECC
RDIMM
DRx8 ECC
RDIMM
DRx4 ECC
 Note: DDR4 2400MHz is only available on Intel Xeon® D-1541 processor.
 When only one DIMM is used, it must be populated in memory slot0 first.
 System will not boot normally with incorrect populated sequence.

仅Intel Xeon® D-1541处理器支持DDR4-2400MHz内存。

只使用一个DIMM时，必须安装到内存插槽0。

若安装顺序有误，系统将不能正常引导。
Jumper Settings/ 跳线设置
No. Desription
1 Clear CMOS Jumper
1-2 Close: Normal operation (Default setting)
2-3 Close: Clear CMOS data.
2 ME Update Jumper
1-2 Close: ME update.
2-3 Close: Normal operation (Default setting)
3 ME Recovery Jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: ME recovery mode.
4 S3 Power On Select Jumper
1-2 Close: Stop an initial power on when BMC is not ready.
2-3 Close: Keep initial power on. (Default setting)
System Status LED:
Description
State Description
Green On Normal operation
Amber On
Critical alert.
Off System is not ready
Power button/LED:
State Description
Green On System is powered on
Description
Off System is powered off
ID switch button w/LED:
State Description
Blue On Unit selected for identification
Off No identification
Speed (MT/s);
Slot Per Channel (SPC) and DIMM Per Channel (DPC)
1 Slot Per Channel 2 Slot Per Channel
1DPC 1DPC 2DPC
1600, 1866, 2133, 2400*
1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400*
1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400*
1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400*
1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400* 1600, 1866, 2133, 2400*