Advertisement
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
K2C100
K2C200
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
K2W100
K2W200
Monitor Arm Series
Spanish Product Description
German Product Description
Portuguese Product Description
French Product Description
K2P100
K2P200
Italian Product Description
Dutch Product Description
K2 Series
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CHIEF K2 Series
Summary of Contents for CHIEF K2 Series
- Page 1 Instrucciones de instalación Istruzioni di installazione Installationsanleitung Installatie-instructies Instruções de Instalação Instructions d´installation K2W100 K2P100 K2C100 K2W200 K2P200 K2C200 Monitor Arm Series Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description K2 Series...
-
Page 2: Important Safety Instructions
It is the installer’s responsibility to make sure the combined weight of all components located between the K2 Series Monitor Arm up to (and including) the display does not exceed 40 lbs (18.14 kg) for single arm mounts or 25 lbs (11.34 kg) per arm on dual arm mounts. - Page 3 Installation Instructions K2 Series DIMENSIONS K2C100 188.1 7.41 (8.85 [224.7] FOR LOWER PROFILE INSTALL) LOWER PROFILE INSTALL EXTENSION 3.94 MAX 19.2 [487.7] PITCH PITCH 2.95 RANGE TENSION KNOB 90 INTERFACE ROTATION MANUAL HEIGHT ADJUSTMENT RANGE 244.5 9.63 LOWER PROFILE 289.7 11.41...
- Page 4 Installation Instructions K2 Series DIMENSIONS (CONTINUED) K2W100 3.94 EXTENSION MIN 2.98 [75.7] 2.95 MAX 17.2 [436.9] 90 INTERFACE ROTATION PITCH TENSION KNOB PITCH RANGE 149.6 5.89 263.7 10.38 81.7 5.508 3.22 CABLE MANAGEMENT 61.6 2.43 K2W200 MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 28.25" [717.6] EXTENSION MIN 2.98 [75.7]...
- Page 5 K2 Series Installation Instructions DIMENSIONS (CONTINUED) K2P100 POLE CLAMP RANGE 1.50 [38.1] - 1.90 [48.3] 78.8 3.10 MAX EXTENSION 16.60 [421.6] 3.94 90 INTERFACE ROTATION 2.95 PITCH TENSION KNOB PITCH RANGE 10.484 CABLE MANAGEMENT K2P200 POLE CLAMP RANGE 1.50 [38.1] - 1.90 [48.3] MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 28.25 "...
- Page 6 K2 Series Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación...
-
Page 7: Tools Required For Installation
K2 Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" (included) 5/32" (included with K1P Series only) PARTS A (1) [monitor arm] (K2W100 shown) *8 screws and washers included with dual arm mounts C (4 or 8)* D (4 or 8)*... -
Page 8: Assembly And Installation
K2 Series Installation Instructions Assembly And Installation IMPORTANT ! : IF you will be installing a SINGLE display with RECESSED mounting holes, then proceed to "DISPLAY INSTALLATION" before continuing with this mount installation procedure. Connecting K2C Series (column mount) to Desk... - Page 9 K2 Series Installation Instructions set screw 3/16" x 2 1/2" side view (F) x 2 (G) x 2 Figure 5 Connecting K2W Series (wall mount) to Wall Determine mounting location on wall. Use a stud finder to locate stud. Use wall bracket to mark and drill two 3/16" x 2 1/2" holes in wall at desired mounting location.
-
Page 10: Display Installation
K2 Series Installation Instructions Display Installation Recessed Mounting Holes Ensure Centris bracket is able to swivel and tilt easily, yet The mounting holes on the back of the display will either be still be tight enough to hold display in desired position. -
Page 11: Cable Management
Installation Instructions K2 Series Pivot Adjustment Range Swing Arm Pivot Adjustment Adjust pivot position as desired. (See Figure 12) Single Arm Models (K2C100, K2W100 and K2P100) Adjust pivot point tension screws to change pivot Adjust arm angle as desired up to 90 degrees in either adjustment tension. - Page 12 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Chief Manufacturing, a products division Asia Pacific A Office No. 1 on 12/F, Shatin Galleria of Milestone AV Technologies 18-24 Shan Mei Street...
Need help?
Do you have a question about the K2 Series and is the answer not in the manual?
Questions and answers