Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Foster FlexDrawer FFC2-1
Summary of Contents for Foster FlexDrawer FFC2-1
- Page 1 User Manual FlexDrawer FFC2-1, FFC3-1, FFC4-2, FFC6-2.
- Page 2 Four Steps to extend the life of your appliance Getting to know your new Foster appliance Installation Using the appliance Maintenance www.fosterrefrigerator.com...
- Page 3 All installations must conform to local and municipal regulations and directives. In case of doubt contact your Foster authorised distributor or the Foster Technical Department. The information contained in this manual is current at the time of publication and is subject to change without notice.
-
Page 4: Climate Class
Climate Class Climate class indicated on the serial plate shows the ambient temperature & humidity at which this appli- ance has been tested, for the purposes of establishing values in line with European standards. Climate Class Temperature Relative humidity 30˚C 40˚C General Safety Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance. -
Page 5: Electrical Safety
Electrical Safety This equipment shall be connected to an electrical supply protected by a Residual Current Device (RCD). This may include a residual current circuit breaker (RCCB) type socket, or through a Residual Current Circuit Breaker with overload protection (RCBO) supplied circuit. Should it be necessary to replace the fuse, the replacement fuse must be of the value stated on the serial label for the appliance. -
Page 6: Installation
Installation Removal of packaging Prior to carrying out this operation please ensure that these instructions have been read, understood and that the necessary personnel and tools are available to ensure that these instructions are complied with. It is also recommended that a full assessment of the installation conditions and requirements be conduct- ed prior to commencing this operation. - Page 7 Position the pallet against a flat surface of a similar height to the pallet. Ensure that the castors and appliance drawers are locked. Support the appliance at the front and rear. Cut the support straps on both sides and unlock the castors. Carefully slide the appliance off the pallet onto the adjacent level surface.
- Page 8 Start-Up and Test Sequence After unpacking, clean (cleaning directions supplied within this manual) and allow the appliance to stand for 60 minutes before turning on. Ensure the appliance is situated on a firm, level surface, away from both hot and cold air sources, as this will affect its performance.
-
Page 9: Using The Appliance
Using the appliance Display Icons and Buttons Icon e Button 2 Icon a º Button 1 Icon b Icon c Button 3 Icon d Icon g Icon f Button 4 Icon Button Compressor On / Alarm On / Off / Standby Evaporator fans on Up / Increase value Defrost on... -
Page 10: Set Point
Adjust the set point using button 2 to increase and button 4 to decrease. Press button 1 to save the new value. If button 1 is not pressed the new value will not be stored. Exit by pressing button 3. If the Set Point cannot be adjusted to the value required please contact your authorised Foster dealer for advice. -
Page 11: Alarms Notification
Alarms Notification If an alarm condition occurs the appliance will indicate this with an audible signal, by illuminating icon ‘a’ and displaying a fault code from the list in the ‘Troubleshooting’ section of this manual. The audible notification can be muted temporarily by pressing button 1. While the fault is still present icon ‘a’... -
Page 12: Cleaning And Maintenance
6 to 12 months to maintain your warranty and ensure optimal performance of your appliance. 6-12 MONTHS We recommend that service is carried out by an authorised Foster agent or by contacting the Foster Service team using the contact details in this manual. - Page 13 Cleaning Condenser Air Grill Use a soft brush or vacuum to remove loose dust and dirt from the Condenser Air Grill. Condenser Regular cleaning of the condenser (located behind the Condenser Air Grill) increases energy efficiency and prolongs the life of your appliance. Never use a wire brush, abrasive or corrosive materials to clean the condenser.
- Page 14 Gasket All door gaskets should be inspected on a regular basis and replaced as necessary if damaged. To clean, wipe with a warm damp soapy cloth followed by a clean damp cloth. Finally dry thoroughly. www.fosterrefrigerator.com...
-
Page 15: Troubleshooting
Service to arrange for this to be replaced. During this time the appliance cannot maintain an accurate temperature and all product should be removed and the appliance switched off. tE - This indicates that the evaporator probe has failed. Call your authorised dealer or Foster Service to arrange for this to be replaced. - Page 16 If the reason for the malfunction cannot be identified, disconnect the electrical supply from the appliance and contact your authorised dealer or Foster Service. When requesting a service call, please quote the model and serial number which can be found on the inside of the appliance on the right hand wall and begins with ‘E’...
- Page 17 Notes FlexDrawer - User Manual...
- Page 18 Notes www.fosterrefrigerator.com...
- Page 19 Notes FlexDrawer - User Manual...
- Page 20 For more information: For service and spares: +44 (0) 1553 698485 For service +44 (0) 1553 780333 regional@foster-gamko.com service@foster-gamko.com fosterrefrigerator.com For parts +44 (0) 1553 780300 parts@foster-gamko.com Document ID code: 00-570689v2 Original Instructions www.fosterrefrigerator.com...
Need help?
Do you have a question about the FlexDrawer FFC2-1 and is the answer not in the manual?
Questions and answers