Download Print this page

Merrytek MC054V RC2 User Manual

Microwave motion sensor

Advertisement

Quick Links

I
MC054V RC2
- ®
m e
「 也 毡k
'
MICROWAVE MOTION SENSOR USER
S MANUAL
Model No.: MC054V RC2
地C)b
f
v
J
MC054VRC2 A
MC054V RC:Z B
1¥1
MC054VRC2 C
MC054VRC2D
SA A( 《!
FEATURE
• Sensor parameters can be conveniently set by a remote control.
• Mounting height up to 15
max., suitable for warehouse use.
『n
•Water proof sensor with IP65 rating.
• Automatic dimming when used in combination with 1-1 OV dim
able
『『,
control gea
s.
• Built-in adjustable daylight sensor.
• 1-10V interface can match up with Merrytek stand-alone daylight sensor
.。
MS01 and achieve daylight harvesting.
ptional mounting brackets for different application.
SPECIFICATI
NS
Input voltage
120/270Vac, 50/60Hz
Rated load
400W-lnductive
800W-Resistive
Surge current of i
ad
50A(:到%1
」由国黑lOuS, 277Vac full load, cold start);
..,. ,
80A(50% 1
,」
=200uS, 2TNac, full load, cold血rt)
,...
.,
Detection a
ea
100%/75%/50%/25%
Hold time
55/305/1 min/3min/5min/斗Omin/20min/30min
Daylight sense
5 lux/15Lux/30Lu x/50Lux/1 OOlux/150lux/Disable
Stand-by period
Os/105/1 min/3min/5min/1 Omin/30min/+oo
Stand-by dimming level
10% / 20% /30% /50%
Sensor principle
Microwave motion detecto
Microwave frequency
5.SGHz
75MHz, ISM wave band
M口unti ng height
15m Max.
Detection angle
150"(Wall installatio时,
360"(Ceiling installation)
Motion detection
0.5-3 m/s
Operating temperature
-35"C-55" C
IP rating
I P65 (INDO
R USE
NLY)
Factory Setting
Detection area:75%,Hold time:5s, Stand-by Period: Os,
:'
Stand-by dim level
0%, Daylight Sensor: Disable
GENERAL GUIDELINES F
R INSTALLATI
',The sens
r should be installed by a qualified electrician. And ensure that the
electricity supply is switched o仔before installing o
2, Installation inside a glass o
plastic housing will
esult in a reduction of
detection sensitivity. Expect a reduction of approximately 20% for every
3mm of thickness.
3, Detecti口n area will be affected by speed 口f moti口同
v口lume of m口vin g object.
4, Daylight sensor was tested on sunny environment with no lampshade.
ambient lux level could be different unde
different weathe
season or environ r『1ent
Application Notice
1, Sensors settings may need to be adju民ed to match installation si钮,please follow
below instructions or contact manufacturer.
2,The sensor is designed for indoor use only. Outdoor use
the waterproof effects. The raining or wind blowing may trigger the microwave
sensor even if without human motion when outd口or use.
3, The distance between any two senso陌should be at least 3m to avoid interference
with each other.
4, When the microwave sensor is installed in a metal lighting fixture or space with
large reflector, for exam pie a warehouse with metal ro时,the microwave will be
reflected and cause the lights permanently illuminated even if without motion
signal. Please reduce the detection a陪a (sensitivity)旬solve the problems, or
contact the microwave sensor manufacturer to provide technical support.
5, Make sure the sensor not close to or be blocked by high density material, such
metal, glass, concrete walls etc. The materials will reduce o
cause false trigger.
6, Make sure there are no fans or other vibrating objects in installation area.
The movements will trigger sensor as well.
Initialization
1, ON/OFF function or 3-step dimming function:
A仕er p口wer o
, the sensor automatically turns on light at 100% brightness.
『1
After 1 Osec, it completely turns o何light.
During the initialization, the sensor is not able to detect movement.
2, 2-step dimming function:
After power on, the sensor automatically turns on light at 100% brightness.
After 1 Osec, it dims the light to a low light level (set by stand-by dim level).
During the initialization, the sensor is not able to detect m口ve
DETECTI
N PATTERN(F
R CEILING M
N
DETECTION PAπERN
servicing the product.
height of installation and
climate,
『,
for
a long time may reduce
block microwave and
1ent.
『『
INSTALLATION
--
-----
MC054V RC:2 A
3
L
3
E
E
M
UNTING)
O
l
h
×
: :
!'-
...
'
1
l飞
气:: 1:二:; 只
i
I
(No饵Please do not set the detection sensi由ity to 25%/50%when mounting
\
-------
---
I
MC054V RC:2 B
MC054VRC2 C
。〉
Rotatable Metal Bracket
val Surface Mounted日racket
伽圆胁
2X
1X
M4.0X251!1TI Sc
『酬
du
a后,
翩翩'"
一一一一一一一一-
4
7
、、
m
J
K
E
m
ι
J
w
J
i
d
V〈
J
F
t
J
剑,'咱
...
'
ι
u
M
1
L
i
V
r
J
H
V
W
ι
J
J J
r
u丁川
J
J
r
J
J
l
'
F
×
m
I
d
J
K
m
E
E
E
m
h
J
1
'
Sloww画lk
�院:
'
l
R/
飞出,
l
×',T
i
,,入
Mounting height:1Sm
.it the helg ht of 1 Sm)
-一
--------
'
MC054VRC2 D
"'
伽踊胁
4X
ox.Bnrn岛附
.l.
一一一一一一一一-

Advertisement

loading
Need help?

Need help?

Do you have a question about the MC054V RC2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Merrytek MC054V RC2

  • Page 1 『『, "' control gea 自 『 • Built-in adjustable daylight sensor. 曲 • 1-10V interface can match up with Merrytek stand-alone daylight sensor .。 MS01 and achieve daylight harvesting. - 。 ptional mounting brackets for different application. | -...
  • Page 3 FCC Warning This device complies with part 15 of the FCC rules. -Reorient or relocate the receiving antenna. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) ·Increase the separation between the equipment and this device must accept any inte rference received, receiver.

This manual is also suitable for:

Mc054v rc2 aMc054v rc2 bMc054v rc2 cMc054v rc2 d