BLUM MINIPRESS MSP Manual
  1. Manuals
  2. Brands
  3. BLUM Manuals
  4. Power Tool
  5. MINIPRESS MSP
  6. Manual
BLUM MINIPRESS MSP Manual

BLUM MINIPRESS MSP Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MINIPRESS MSP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BLUM MINIPRESS MSP

Summary of Contents for BLUM MINIPRESS MSP

  • Page 4: Table Of Contents

    CONTENTS: PAGE: Description of parts SAFETY RULES: Read BEFORE operation ! 3 -4 Warranty conditions Initial machine set-up 6 - 7 Connection of Air Supply Connection of Electrical Power Supply 8 - 9 Machine functions 10 - 11 Hinge insertion 12 - 20 Installation of Mounting Plates 21 - 23...

  • Page 5: Description Of Parts

    DESCRIPTION OF PARTS A 1 ... Control Box E 4 ... Fixing Pin for Drill Head A 2 ... Hex Set Screw E 5 ... Lever (to rotate gearbox) A 5 ... Clamping Lever for Base E 6 ... Symbol for Hinge Drilling Ruler Pattern A 6 ...

  • Page 6: Safety Rules

    READ BEFORE YOU START OPERATING! SAFETY RULES: This machine is designed for commercial and industrial applications only, and should be used by professionals, fully trained in it´s operation. It is not intended for use by consumers. Before connecting your machine to a Power Source, be sure to read ALL Safety Rules and the Instruction Manual! 7.
  • Page 7 21. CAUTION! For your own safety, use etc. only those accessories which are recommended or indicated in the instruction sheets or by Blum (catalog). 16. Maintain tools with care. Keep tools sharp, clean, and organized for best and safest performance. Follow instructions for lubricating and changing accessories.

  • Page 8: Warranty Conditions

    U.S. address in Stanley, N.C.) “Waranty reply” The Blum MINIPRESS "MSP" is warranted to be free of defects in materials and work- manship for a period of one year from the date of purchase. This warranty is in lieu of any other warranties expressed or implied.

  • Page 9: A Initial Machine Set-Up Msp

    Section A INITIAL MACHINE SET-UP Swing out the pictured page at the front of the instruction sheet, for easier identifi- • Loosen both Clamping Levers (A5) cation of the described parts. on the Fencing System (A6). 1. FASTEN MACHINE FIRM ONTO A RIGID •...
  • Page 10 4. PLACE POSITIONING STOPS (A10) 5. WORKTABLE ATTACHMENT • Slide Positioning Stops onto the Base • Place Worktable (A15) on bottomrails of Ruler (A8) with the Swivel Part (A12) machine with cutouts facing the Fence. facing away from the machine. Position Support Brackets (A11) in bottom rails.

  • Page 11: Connection Of Air Supply

    Section B Section C CONNECTION OF AIR SUPPLY CONNECTION OF POWER SUPPLY 1. CONNECTION OF AIR SUPPLY 1. THE ELECTRICAL CONNECTION MUST BE PERFORMED BY A QUALIFIED • Attach a 1/4" I.D. flexible hose on top of ELECTRICIAN. barbed hose fitting at Check Valve (B1). •...

  • Page 12: Check Motor Direction

    D1 D2 2. CHECK MOTOR DIRECTION 3. CHUCK ROTATION DIRECTION WARNING: To avoid serious injury stay If the motor rotation direction is correct: clear of drilling area and all pinch points! • the orange marked Chucks (C5) rotate counter-clockwise. • Remove all tools and objects from worktable •...

  • Page 13: Machine Functions

    Section D MACHINE FUNCTIONS WARNING:To avoid serious injury stay 2. DRILL/PRESS MODE - DRILLING clear of drilling area and all pinch points! • Set Key Switch to pos. 2. NOTE: Machine functions should be te- • Stroke Button illuminates. Electric and sted without drill bits and work Pneumatics are active and Key cannot piece.

  • Page 14: Hold Down Clamps

    3. DRILL/PRESS-MODE - INSERTING 4. HOLD DOWN CLAMPS • Key Switch (D2) must be in pos.2. WARNING:Keep hands and fingers clear of Hold Down Clamps! • Move Swing Arm (C2) down to Stop (E20). • Key Switch must be in either pos. 1 or 2.

  • Page 15: Hinge Insertion

    To correct drill-bit length, adjust screw (marked orange). accordingly. • Two Cover Caps (E7) NOTE: All drill bits have to be the same length ! • Insertion Ram MZM.XXXX (E3). See Blum catalog for correct Ram. • Door panel • Hinge...
  • Page 16 Ø 8 Ø 35 Ø 8 3. SELECT DRILL PATTERN 4. INSTALL DRILL BITS • Set Main-Switch to pos. 0. • Pull out Fixing Pin (E4) on Drill Head. • Push drill bits all the way in • At the same time, move Lever (E5) to the chucks.
  • Page 17 5. CHECK DRILLING DEPTH 6. CORRECTING DRILL DEPTH ADJUSTMENT ADJUSTMENT WARNING:To avoid serious injury stay • If the Cutting edges do not touch the clear of drilling area and all door panel top, correct adjustment. pinch points! NOTE: One turn on the Depth •...

  • Page 18: Pneumatic Brake

    D1 D2 D3 E 12 7. PNEUMATIC BRAKE 8. ADJUSTMENT OF BRAKE The Pneumatic Brake causes the Drill Head Adjustment Screw (E12) allows variable to slow down before the drill bits contact stroke speeds for different materials. the board. This assures chip-free holes and longer bit life.
  • Page 19 9. FENCING SYSTEM (A6) 10.ADJUST POSITIONING STOPS (A10) ADJUSTMENTS: Adjust Positioning Stops to the desired position on the Base Ruler. • Release Clamping Levers (E14) NOTE: The reference edge can be on • Pull out Locating Pins (E15), and either side of the Swivel Part (A12). adjust Fencing System to pos.
  • Page 20 12.ADJUST HOLD DOWN CLAMPS (E16) 11.PUSH DOOR AGAINST THE FENCE AND SLIDE UNTIL IT IS POSITIONED • Loosen Clamp Screw (E17). AGAINST THE STOP. • Position Clamp over panel surface. • Adjust Clamps, so that the distance x between door and Guard (E18) is not more than 1/8"...
  • Page 21 13.MOUNT INSERTION RAM (E3) ONTO 14.POSITION HINGE ON INSERTION RAM SWING ARM (C2) • Snap hinge cup onto front of Insertion • Place Ram over Fixing Screws Ram, and swing hinge arm into slot until (E19) on Swing Arm and tighten. it locks in place.
  • Page 22 E 13 D1 D2 D3 15.DRILLING 16.AIR JET (E13) ADJUSTMENT WARNING: To avoid serious injury stay WARNING: To avoid serious injury the clear of drilling area and all machine must be off when pinch points! adjusting the Air Jet. • Make sure that no objects are on the •...
  • Page 23 D1 D2 D3 17.CHECK ALIGNMENT OF SWING ARM 18.HINGE INSERTION (C2) WARNING: To avoid serious injury stay • Move Swing Arm down to Stop (E20) clear of drilling area and all pinch points! • Make sure the hinge is aligned with the drilled hole.

  • Page 24: F Installation Of Mounting Plates

    Section F DRILLING FOR MOUNTING PLATES WITH SYSTEM SCREWS Ø 5 Ø 5 3. CHANGE DRILL PATTERN 1. NECESSARY PARTS • Pull out Fixing Pin (E4) on Drill Head. • Drill bits: - one 5 mm dia. rotating clock- wise (F1) (marked black) •...
  • Page 25 7. ADJUST FENCING SYSTEM (A6) 8. ADJUST POSITIONING STOPS (A10) • Release Clamping Levers (E14) • The “0”-pos. on the Base Ruler (A8) scale can be centered between the • Pull out Locating Pins (E15) and line boring spindles by shifting the Base adjust Fencing System to pos.
  • Page 26 D1 D2 D3 9. SLIDE CABINET SIDE PANEL AGAINST 11.DRILLING THE FENCE UNTIL POSITIONED AT THE (see page 19, point 15) STOP WARNING: To avoid serious injury stay 10.ADJUST HOLD DOWN CLAMPS (E16) clear of drilling area and all pinch points! (see page 17, point 12) 12.RELEASING HOLD DOWN CLAMPS •...

  • Page 27: Line Boring Pattern

    Section G LINE BORING PATTERN Ø 5 Ø 5 Ø 5 3. CHANGE DRILL PATTERN 1. NECESSARY PARTS • Pull out Fixing Pin (E4) on Drill • Drill bits: - one 5 mm dia. rotating clock- Head. wise (G1) (marked black) -two 5 mm dia.
  • Page 28 7. ADJUST FENCING SYSTEM (A6) 8. ADJUST POSITIONING STOPS (A10) • Release Clamping Levers (E14). • Adjust one Stop at the correct measure- ment for the first set of holes, and • Pull out Locating Pin (E15), and tighten. adjust Fencing System to pos. SY. LINE BORING: •...
  • Page 29 D1 D2 D3 9. SLIDE CABINET SIDE PANEL AGAINST 11.DRILLING THE FENCE UNTIL POSITIONED AT THE (see page 19, point 15) STOP. WARNING: To avoid serious injury stay 10.ADJUST HOLD DOWN CLAMPS (E16) clear of drilling area and all pinch points! (see page 17, point 12) 12.RELEASING HOLD DOWN CLAMPS •...

  • Page 30: H Maintenance

    Section H Section I TROUBLE-SHOOTING MAINTENANCE AND CARE WHAT TO DO WHEN? MAINTENANCE: 1. WRONG MOTOR DIRECTION • Clean machine periodically to assure This correction must only be done by proper performance. a qualified electrician! • Check Air Filter (H1) weekly (approx. 40 NOTE: On single-phase models the hrs.

  • Page 31: Other Problems

    2. LIGHT INSIDE STROKE BUTTON DOES 3. OTHER PROBLEMS NOT WORK Contact your Blum distributor or the Blum Check light bulb inside Button, and change Customer Service Department immediate- if necessary (24V DC 3W): • Disconnect machine from power Please give them the serial and model supply.

  • Page 32: Technical Data

    Section J TECHNICAL DATA 1. TECHNICAL DATA 2. PNEUMATIC DIAGRAM (see addendum) Voltage: see label (C1) attached to power cord 3. ELECTRICAL DIAGRAM (see addendum) Connection power: 3-phase 1,2kW, either 220V/60Hz, 3.3A or 440V/60Hz, 1.65A Single-phase 1.2kW, 220V/60Hz, 6.2A RPM: see motor tag Weight: 99 lbs (without table) Measurements: height - 650 mm (26")
  • Page 33 NOTES:...
  • Page 34 NOTES:...
  • Page 35 NOTES: Subject to technical changes without notice. Id. Nr. 431.800.0 Printed in Austria BA-01.02USA / 03.01...

Table of Contents