Related Manuals for BLUM MINIPRESS M
Summary of Contents for BLUM MINIPRESS M
- Page 1 051140 MINIPRESS M Please keep a copy of the operating instructions. The operating instructions contain the EC Declaration of Conformity, which must be produced for authorities upon request. BA-100/1EN M52.XXXX...
-
Page 2: A - Orientation Diagram
A - Orientation diagram BA-100/1EN M52.XXXX... -
Page 3: Table Of Contents
B - Table of contents A - Orientation diagram B - Table of contents B - Table of contents C - Guidelines on using this manual C.1 - How to use these operating instructions D - Safety information D.1- Remaining risks according to ISO EN 12100-2 D.2 - Safety decals D.3 - Intended use D.4 - Safety information... -
Page 4: B - Table Of Contents
B - Table of contents 5 - Maintenance and service 5.1 - Maintenance 5.1.1) Maintenance 5.1.2) Damaged coupling (clutch) 6 - Troubleshooting 6.1 - Error during drilling 6.2 - Fitting insertion error 6.3 - Function errors 7 - Appendix 7.1 – User-supplied work table 8 - Diagrams 8.1 - Electrical diagram 1x 230 V 50 Hz Notes... -
Page 5: C - Guidelines On Using This Manual
Dear valued Blum customer, We would like to congratulate you on your decision to purchase the Blum assembly machine. You are now the owner of a modern, high-quality assembly machine that will give you years of productive use with the proper care and maintenance. -
Page 6: D - Safety Information
D - Safety information D.1- Remaining risks according to ISO EN 12100-2 The machine complies with the current safety standards. However, risks remain for: • The operator and second persons due to the stroke movement of the drilling unit and especially in cases where safety devices are removed or control elements should fail. -
Page 7: Noise Emission
• Make sure that no other tools or objects are on the work table aside from your work piece before turning on the assembly machine. • After finishing work, disconnect the machine from the power supply. • CAUTION: For your own safety, use only those accessories which are recommended or indicated in the manual or Blum sales literature. - Page 8 Пробивни машини Bore- og beslagssætmaskiner Bohr- und Beschlagsetzmaschine Drilling and insertion machine Puurimis- ja sisestusmasinad Asennusporakoneet Machine pour percer et poser des ferrures Μηχάνημα διάτρησης και τοποθέτησης Macchina forainseritrice Urbšanas un furnitūras iestrādāšanas iekārta Gręžimo-montavimo staklės Boor- en beslagmachines Maszyna do nawiercania i osadzania okuć Furadeira e máquina para a montagem de ferragens Maşină...
-
Page 9: F- Ec Declaration Of Conformity / Techn. Data
F - EC Declaration of Conformity / Techn. Data F.1 - EC Declaration of Conformity Julius Blum GmbH, Industriestr. 1, A-6973 Höchst herewith declare on our own responsibility that the product MINIPRESS (M52.xxxx) with drilling heads (MZK.1000, MZK.1900, MZK.8000, MZK.8800) to which this Declaration refers, complies... -
Page 10: Assembly Machine Setup
1 - Assembly machine setup 1.1 - Unpacking and assembly 1.1.1) Assembly machine space requirement H= 966 mm B= 600 mm T= 531 mm • Completely loosen bottom knurled screw ATTENTION: To lift assembly machine only use hitch and load pick up device! 1.1.2) Unpacking assembly machine and attaching to a suitable table •... -
Page 11: 4) Attaching Swivel Stops (Optional)
1 - Assembly machine setup 1.1.4) Attaching swivel stops (optional) • Loosen clamping screw until the location plate protrudes 10 mm • Attach swivel stop to ruler at an angle and stand upright • Tighten clamping screw Note: This procedure can also be used to set a stop between two available stops. -
Page 12: Assembly
2 - Assembly 2.1 - Furniture hinge assembly 2.1.1) Required parts • Drill bits: 1x ø 35 mm clockwise (2.1) (marked in black) 2x ø 8 mm counterclockwise (2.2) (marked in red) • Cover caps (2.3) • Insertion ram MZM.00XX (2.4) (see catalogue to determine the proper insertion ram for the respective furniture hinge) -
Page 13: 6) Drilling Depth Stop
2 - Assembly 2.1.6) Drilling depth stop (2.11) Another option to maintain a constant drilling depth is to install the drilling depth stop. When the drilling depth stop is installed, the drilling depth is always 13 mm regardless of the thickness of the work piece. Installing the drilling depth stop: •... -
Page 14: 8) Setting Swivel Stops (Optional)
2 - Assembly 2.1.8) Setting swivel stops (optional) (1.7) Set the swivel stops (1.7) to the desired dimension and clamp. IMPORTANT: Indicator edge is on the inside of the swivel part. 2.1.9) Placing door on the work table and pushing up against the stop IMPORTANT: The stop surface can be enlarged by swivelling the stop flap forward for grooved work pieces and work pieces with radii (see picture). -
Page 15: 12) Drilling
2 - Assembly 2.1.12) Drilling ATTENTION: All items except for the work piece should be removed from the work area of the assembly machine. Keep your hands out of work area (A). • Swing arm(2.8) must be swivelled up. • Hold down door outside of danger area (A) and press against the swivel stop (1.7) •... -
Page 16: Assembly
3 - Assembly 3.1 - Cruciform mounting plate assembly 3.1.1) Required parts • Drill bits: 1 x ø5 mm clockwise (3.1) (marked in black) 1 x ø5 mm counterclockwise (3.2) (marked in red) • Cover caps (2.3) • Carcase side •... -
Page 17: Assembly
4 - Assembly 4.1 - Drilling hole groups 4.1.1) Required parts • Drill bits: 1x ø 5 mm clockwise (4.1) (marked in black) 2x ø 5 mm counterclockwise (4.2) (marked in red) • Cover caps (2.3) • Setup gauge(4.3) • Carcase side 4.1.2) Setting drill bit length (See point 2.1.2) 4.1.3) Setting drilling pattern... -
Page 18: Maintenance And Service
5 - Maintenance and service 5.1 - Maintenance 5.1.1) Maintenance • Drilling dust should be removed from the assembly machine on a regular basis • Electrical lines should always be checked for damage before the machine is used • The supports are maintenance free and should not be oiled •... -
Page 19: Troubleshooting
6 - Troubleshooting 6.1 - Error during drilling Error Cause Solution Comment Drilled holes too lar- Drill diameter is too large Check drill none ge, oval or ragged Drills are twisted Replace drill none Drilling speed is too high Pull handle down slower See point 2.1.12 Drilling through work pieces Use roof tip drill bit to drill through... - Page 20 6 - Troubleshooting 6.1 - Error during drilling Error Cause Solution Comment Drilling depth does Drilling depth set incorrectly Correct drilling depth setting See point 2.1.5 not match Drilling length does not match Drilling length set to 57 mm See point 2.1.2 Drill bits not completely pushed into the Clean dirt from chuck and completely insert See chapter 2...
-
Page 21: Fitting Insertion Error
6 - Troubleshooting 6.2 - Fitting insertion error Error Cause Solution Comment Fittings cannot be Insertion ram or swing arm is driving Remove object none inserted or only with against an object (e.g. swivel stop) great difficulty The surface of the work piece is too hard Bevel drillings Use slip-on counter- sink... -
Page 22: Function Errors
6 - Troubleshooting 6.3 - Function errors Error Cause Solution Comment Motor does not run Assembly machine is not connected to Connect assembly machine to the power none the power supply supply Building fuse has failed Reset fuse or replace none Swing arm is swivelled down Swivel up swing arm... -
Page 23: Appendix
7 - Appendix 7.1 – User-supplied work table 184,5 184,5 Detail X • If you are making your own work table, use plywood or laminated wood for the support plate. • In addition, please use the screws supplied for fixing the work table. BA-100/1EN M52.XXXX... -
Page 24: Diagrams
8 - Diagrams 8.1 - Electrical diagram 1x 230 V 50 Hz BA-100/1EN M52.XXXX... -
Page 25: Notes
Notes BA-100/1EN M52.XXXX... - Page 26 Notes BA-100/1EN M52.XXXX...
- Page 27 Notes BA-100/1EN M52.XXXX...