Page 2
This document is intended for use by Nokia’s customers (“You”/”Your”) in connection with a product purchased or licensed from any company within Nokia Group of Companies. Use this document as agreed. You agree to notify Nokia of any errors you may find in this document;...
XS-2437X-B unit data sheet.........................47 Overview ............................47 XS-2437X-B part numbers and identification ..................47 XS-2437X-B general description.......................49 XS-2437X-B software and installation feature support ..............55 XS-2437X-B interfaces and interface capacity..................55 XS-2437X-B LEDs ..........................57 XS-2437X-B detailed specifications ....................59 XS-2437X-B GEM ports and T-CONTs .....................60 XS-2437X-B performance monitoring statistics ................61...
Page 4
Nokia ONT 5.10 XS-2437X-B functional blocks......................61 5.11 XS-2437X-B standards compliance ....................62 5.12 XS-2437X-B special considerations....................64 Install or replace an XS-2437X-B indoor ONT ...................67 Overview ............................67 Purpose.............................67 General .............................67 Prerequisites .............................67 Recommended tools .........................67 Safety information ..........................68 Install an XS-2437X-B indoor ONT ....................70 Wall mount an XS-2437X-B indoor ONT...................72...
Page 16
About this document Nokia ONT Nokia quality processes Nokia’s ONT manufacturing, testing, and inspecting practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ- 30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met.
If you are a new user and require access to this service, contact your Nokia sales representative. Select Products. Type your product name in the Find and select a product field and click the search icon.
For details, refer to the Nokia Support portal (https://customer.nokia.com/support/s/). For ordering information, contact your Nokia sales representative. How to comment Note to reviewers: The following "How to comment" text will appear in the final document when it is published. However, the feedback method described below is for use only on final documents.
The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property.
The label may be found in this documentation or on the product. Figure 3-2 Products above MCV value label Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories.
EU market after 1 July 2006, with various exemptions, including an exemption for lead solder in network infrastructure equipment. Nokia products shipped to the EU after 1 July 2006 comply with the EU RoHS Directive.
There can be different requirements for collection and treatment in different member states of the European Union. In compliance with legal requirements and contractual agreements, where applicable, Nokia will offer to provide for the collection and treatment of Nokia products bearing the logo shown in Figure 3-3, “Recycling/take back/disposal of product symbol” (p. 34) at the end of their useful life, or products displaced by Nokia equipment offers.
42 for ONTs containing Class 1 Laser modules certified by original manufactures. Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user.
Possibility of equipment damage. Risk of eye damage by laser radiation. Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user.
The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property.
5.11 XS-2437X-B standards compliance 5.12 XS-2437X-B special considerations XS-2437X-B part numbers and identification Table 5-1, “Identification of XS-2437X-B indoor ONTs” (p. 47) provides part numbers and identification information for the XS-2437X-B indoor ONT. Table 5-1 Identification of XS-2437X-B indoor ONTs...
Table 5-2, “XS-2437X-B power supply ordering information” (p. 48) provides the power supply information for the XS-2437X-B ONT. For more information on power supplies, see the Nokia ONT Power Supply and UPS Guide. Table 5-2 XS-2437X-B power supply ordering information...
Description ONT unit The XS-2437X-B ONT. Wall mount bracket The wall mount bracket is fastened to a wall. The XS-2437X-B ONT is seated in the wall mount bracket. With white color, 1 pcs per box. (3TN01040AA) Wall mount bracket The wall mount bracket is fastened to a wall. The XS-2437X-B ONT is seated in the wall mount bracket.
XS-2437X-B general description Figure 5-1 XS-2437X-B ONT 39533 XS-2437X-B indoor ONTs provide the following functions: • Supports 802.1x port authentication configured via OMCI. • Tri-band concurrent 4x4 802.11 b/g/n/ax/be at 2.4GHz, 4x4 802.11 n/ac/ax/be at 5GHz and 4x4 802.11 n/ac/ax/be at 6GHz •...
Page 51
• Caller ID, call waiting, call hold, 3-way calling, call transfer, message waiting • Forward Error Correction (FEC) • Support for multiple SSIDs (private and public instances); contact your Nokia representative for further details. • Conductive power: 500 mW/27 dBm (2.4 GHz); 1000 mW/30 dBm (5 GHz); 1000 mW/30 dBm (6 GHz) •...
Page 52
• Multi-level firewall and ACL • Supports bridged WAN with three modes (transparent mode, tunnel mode and VLAN-binding mode) 5.3.1 TR-069 parameter support The XS-2437X-B ONT supports the following TR-069 features: • Host object • Port forwarding • Optical parameters •...
Page 53
If the URL is set to the HTTPS format, by default, the connection will use TLS without authentication mode. The ONT can also authenticate the ACS using a pre-installed CA certificate. The XS-2437X-B ONTs support TLSv1.3 for TR069. The ONT supports certification download from ACS.
Page 54
XS-2437X-B general description 5.3.4 TR-104 voice-related alarms The XS-2437X-B ONT supports the following four TR-104 voice-related alarms per FXS port. These alarms represent SIP registration failures with an alarm level of MAJOR. • SIPREGDNS: domain name could not be resolved •...
— — — Notes: 1. The XS-2437X-B ONTs provide service that is enabled and disabled using a on/off switch. 5.5.1 XS-2437X-B connections and components Figure 5-2, “XS-2437X-B indoor ONT physical connections (back)” (p. 56) shows the physical connections for XS-2437X-B indoor ONTs.
LAN3 WLAN ON/OFF 4 -1 0G POWER 39536 The following tables provide LED descriptions for XS-2437X-B indoor ONTs. Table 5-7 XS-2437X-B indoor ONT Front LED descriptions LED color and behavior LED behavior description No power Blue-Green solid Connected to internet and HSI WAN is connected: •...
Phone is in ‘call in’ or ‘talking’ condition Notes: 1. Specific customers may have a different definition. XS-2437X-B detailed specifications The following table lists the physical specifications for XS-2437X-B indoor ONTs. Table 5-9 XS-2437X-B indoor ONT physical specifications Description Specification Depth 7.63 in.
Storage: -4°F to 158°F (-20°C to 70°C) XS-2437X-B GEM ports and T-CONTs Table 5-13, “XS-2437X-B indoor ONT capacity for GEM ports and T-CONTs” (p. 61) lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices.
5.10 XS-2437X-B functional blocks XS-2437X-B indoor ONTs are single-residence ONTs that support Wireless () service. service on these ONTs is compliant with the IEEE 802.11 standard and enabled or disabled using a WLAN button. In addition to the service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports.
39537 5.11 XS-2437X-B standards compliance XS-2437X-B indoor ONTs are compliant with the following standards: • CE marking for European standards for health, safety, and environmental protection • EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands • G.988 support for ONT management and provisioning •...
The XS-2437X-B ONTS qualify as equipment with high network availability (HiNA) functionality. Since the main purpose of XS-2437X-B ONTs is to provide network functionality with HiNA 7 days /24 hours, the modes Off/Standby, Power Management, and Networked Standby are inappropriate.
XS-2437X-B is a package N ONT. 5.12.1 WiFi service XS-2437X-B indoor ONTs feature service as well as voice and data services. WiFi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE 802.11 standards, which the Wi-Fi Alliance defines as the basis for WiFi technology.
XS-2437X-B unit data sheet Nokia ONT XS-2437X-B special considerations The WiFi service on XS-2437X-B indoor ONTs supports the following IEEE standards and Wi-Fi Alliance certifications: • Certified for IEEE 802.11ac/b/g/n/ax/be standards • WPA support including WPA-PSK • Certified for WPA2-Personal •...
Page 66
XS-2437X-B unit data sheet Nokia ONT XS-2437X-B special considerations Table 5-17 XS-2437X-B ONT considerations and limitations (continued) Considerations and limitations The assumptions and limitations of iPerf as fallback of TR-143 on Cortina are: • Maximum throughput that is achieved is 8Gbps upstream and 8Gbps downstream with IPoE WAN with more than three parallel threads (-P option).
Install or replace an XS-2437X-B indoor ONT Nokia ONT Safety information • #2 Phillips screwdriver • 1/4 in. (6 mm) flat blade screwdriver • Wire strippers • Fiber optic splicing tools • RJ-45 cable plug crimp tool • Voltmeter or multimeter •...
Page 69
Install or replace an XS-2437X-B indoor ONT Nokia ONT Safety information To satisfy ISED Canada RF exposure requirements, a separation distance of 30 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.
Use this procedure to install a XS-2437X-B indoor ONT. Place the indoor ONT unit on a flat surface, such as a desk or shelf. Note: The XS-2437X-B cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: •...
Install or replace an XS-2437X-B indoor ONT Nokia ONT Install an XS-2437X-B indoor ONT Figure 6-2 ONT to wall mount connection - PON connector 39535 DANGER Hazard Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters.
ND OF STEPS Wall mount an XS-2437X-B indoor ONT This chapter provides the steps to mount an XS-2437X-B indoor ONT on a wall using a wall mount bracket. The XS-2437X-B indoor ONT is shipped without the wall mount bracket. The wall mount bracket must be ordered separately.
6.5 “Recommended tools” (p. 67) for the recommended tools. 6.8.2 Procedure Use this procedure to mount an XS-2437X-B ONT on a wall. Mount the ONT on a wall using the wall mount bracket, as shown in Figure 6-4, “XS-2437X-B wall mount bracket” (p.
Install or replace an XS-2437X-B indoor ONT Nokia ONT Wall mount an XS-2437X-B indoor ONT Figure 6-4 XS-2437X-B wall mount bracket 64mm 39539 Wall 39538 a. Determine the location of the two anchor holes for the wall mount bracket. The bracket can be used as a template for marking and drilling the holes.
Install or replace an XS-2437X-B indoor ONT Nokia ONT Wall mount an XS-2437X-B indoor ONT Figure 6-5 Connect the fiber optic cable to ONT 39535 d. Install the ONT into the wall mount bracket by lifting the unit above the bracket and placing the ONT onto the bottom ledge of the bracket.
Install or replace an XS-2437X-B indoor ONT Nokia ONT Wall mount an XS-2437X-B indoor ONT Figure 6-6 ONT to wall mount connection 39540 e. Connect the cables. f. Use the longer screw to fix the ONT with the bracket together firmly when the ONT is deployed on the wall.
ND OF STEPS Replace an XS-2437X-B indoor ONT Use this procedure to replace a XS-2437X-B indoor ONT. Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS).
Install or replace an XS-2437X-B indoor ONT Nokia ONT Replace an XS-2437X-B indoor ONT Example: ED-ONT::ONT-1-1-1-1-1; If used, disable the service by pressing the WLAN button; see the following figure for the location of the WLAN button. Figure 6-8 XS-2437X-B indoor ONT connections...
Page 79
Install or replace an XS-2437X-B indoor ONT Nokia ONT Replace an XS-2437X-B indoor ONT DANGER Hazard Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Disconnect the fiber optic cables. See Figure 6-2, “ONT to wall mount connection - PON...
Page 80
If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. Verify the ONT LEDs, voltage status, and optical signal levels; see the Nokia ONT Hardware and Cabling Installation Guide.
ND OF STEPS 6.10 Connect a CyberPower DTC50U12V UPS to XS-2437X-B Use this procedure to connect to an UPS to a XS-2437X-B. Before starting this procedure, ensure that the following items are available: • Battery for the CyberPower UPS DTC50U12V •...
Install or replace an XS-2437X-B indoor ONT Nokia ONT Connect a CyberPower DTC50U12V UPS to XS-2437X-B The connector for the 25 foot 3EM24378AB cable matches the socket for the 50W UPS Cyberpower DTC50U12V. Figure 6-10 Molex 7-pin DC cable 2438.4 30 mm (8ft 1 in.)
Install or replace an XS-2437X-B indoor ONT Nokia ONT Connect a CyberPower DTC50U12V UPS to XS-2437X-B Figure 6-12 Connecting the AC cord to the wall outlet AC power cable CyberPower UPS DTC50U12V with a battery Output connector 3-prong AC plug...
Configure an XS-2437X-B indoor ONT Nokia ONT 7 Configure an XS-2437X-B indoor ONT Overview 7.1.1 Purpose This chapter describes the WebGUI configuration procedures. 7.1.2 Contents 7.1 Overview GUI overview 7.2 General configuration 7.3 HGU mode GUI configuration 7.4 WAN services overview 7.5 Logging in to the web-based GUI...
Page 86
Configure an XS-2437X-B indoor ONT Nokia ONT Overview 7.21 Configuring DNS 7.22 Viewing LAN Statistics WiFi Configuration 7.23 Overview 7.24 Configuring WiFi Network 7.25 Configuring Guest Network 7.26 Configuring the WiFi Password 7.27 Viewing Network Map, Adding WiFi Points, Renaming WiFi Points and Removing WiFi Points 7.28 Optimizing WiFi Network...
Page 87
Configure an XS-2437X-B indoor ONT Nokia ONT Overview Advanced Settings 7.47 Overview 7.48 Configuring Port Forwarding 7.49 Configuring Port Triggering 7.50 Configuring DDNS 7.51 Configuring NTP 7.52 Configuring USB 7.53 Configuring UPNP and DLNA Maintenance 7.54 Overview 7.55 Configuring the Password 7.56 Backing Up the Configuration...
Troubleshooting Guide. HGU mode GUI configuration Use the procedures below to use the web-based GUI for the XS-2437X-B in HGU mode. This mode is preset at delivery. A home gateway unit (HGU) is a home networking device, used as a gateway to connect devices in the home through fiber to the Internet.
Page 89
Configure an XS-2437X-B indoor ONT Nokia ONT GUI overview WAN services overview 7.4.3 Tunnel service In this model, bridging service can be associated with more than one LAN port and a WAN Port. The traffic from the LAN ports whether its tagged or untagged (traffic from SSID will always be untagged) are received on this interface and the Bridge Tunnel service adds a service VLAN to the received traffic and forwards on the WAN port.
Configure an XS-2437X-B indoor ONT Nokia ONT GUI overview WAN services overview Figure 7-1 Common forwarding model Ethernet 0/untagged GPON-OLT OMCI VEIP domain domain WiFi VLAN Router WiFi 0/untagged Guest Router Ethernet 0/untagged transparent 0/untagged WiFi Bridge VLAN 4095 tunnel mode...
Page 91
Configure an XS-2437X-B indoor ONT Nokia ONT GUI overview WAN services overview Table 7-1 Supported combinations of OMCI and ACS/WebGUI (continued) Service Type Operation Untagged traffic at LAN Tagged traffic at LAN Tagged Routed WAN Set WAN P-bit ACS/WebGUI NA (only untagged in for...
Configure an XS-2437X-B indoor ONT Nokia ONT GUI overview Logging in to the web-based GUI Table 7-1 Supported combinations of OMCI and ACS/WebGUI (continued) Service Type Operation Untagged traffic at LAN Tagged traffic at LAN Bridge (VLAN binding, Set WAN P-bit...
WebGUI features. This access for the end-user can be adapted with a WebGUI configuration file. Contact your Nokia representative to know the factory default settings of which WebGUI access is available to your end user or how to get a WebGUI configuration file.
Configure an XS-2437X-B indoor ONT Nokia ONT GUI overview Viewing overview information Click Sign in. The Overview page displays. Note: To help protect the security of your Internet connection, the application displays a pop-up reminder to change both the WiFi password and the ONT password.
Displays the total number of online and offline clients connected to this device (single device or mesh system). XS-2437X-B WebGUI Menu The following table lists the main menu and sub-menu options in the XS-2437X-B WebGUI: Table 7-2 XS-2437X-B WebGUI Menu Main Menu...
Page 96
Configure an XS-2437X-B indoor ONT Nokia ONT GUI overview XS-2437X-B WebGUI Menu Table 7-2 XS-2437X-B WebGUI Menu (continued) Main Menu Sub-menu Procedure Reference WiFi WiFi networks 7.24 “Configuring WiFi Network” (p. 134) WiFi Network map 7.27 “Viewing Network Map, Adding WiFi Points, Renaming WiFi Points and Removing WiFi Points”...
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Overview WAN Configuration Overview This section describes the WAN configuration procedures that can be performed from the following sub-menu options under the WAN menu: Sub-menu Procedure WAN services 7.9 “Configuring WAN Services” (p. 97) WAN statistics 7.10 “Viewing WAN Statistics”...
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring WAN Services Figure 7-8 Bridge mode - Tunnel Configure the following parameters: Table 7-3 WAN services parameters Field Description WAN connection list Select a WAN connection from the list. Enabled Select the toggle button to enable the WAN connection.
Page 104
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring WAN Services Table 7-3 WAN services parameters (continued) Field Description Connection mode Select the connection mode of the WAN connection from the list: • Route Mode • Bridge Mode IP mode This field is applicable only if the connection mode is Route Mode.
Page 105
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring WAN Services Table 7-3 WAN services parameters (continued) Field Description SSID port binding Select the toggle button next to the SSID to enable it. Select the toggle button next to the PVID to enable it.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Viewing WAN Statistics Table 7-3 WAN services parameters (continued) Field Description Echo value Indicates the number of times the device sends messages to the server to check if the IP address is available or not.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Viewing WAN Statistics Figure 7-9 WAN Statistics page Click on the service name to display the WAN statistics details page. Figure 7-10 WAN Statistics page info Table 7-4 WAN statistics parameters...
Page 108
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Viewing WAN Statistics Table 7-4 WAN statistics parameters (continued) Field Description PON link status Displays the PON link status whether it is Up or Down. Service WAN connection list Select a WAN connection from the list.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring TR-069 7.11 Configuring TR-069 Click WAN TR-069 in the left pane. The TR-069 page displays. Figure 7-11 TR-069 page Configure the following parameters: Table 7-5 TR-069 parameters Field Description Enable Select the toggle button to enable CWMP function.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring TR-369 Table 7-5 TR-069 parameters (continued) Field Description Password Enter the password to log in to the ONT. Connect request username Enter the username to log in to the auto-configuration server.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring GRE tunnel Table 7-6 TR-369 parameters Field Description Enable TR369/USP Select the toggle button to enable TR-369/USP and click Save. Controller endpoint ID Enter the controller endpoint ID. MTP Protocol Select the MTP protocol from the list (currently only MQTT is supported).
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring GRE tunnel Figure 7-13 GRE Tunnel page Configure the following parameters: Table 7-7 GRE Tunnel parameters Field Description Tunnel Name Select Create new GRE Tunnel or select an existing tunnel from the list.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring Static routing Table 7-7 GRE Tunnel parameters (continued) Field Description Traffic timeout to start pings Enter the traffic timeout in seconds (2 to 1024). No. of retries before unreachable Enter the number of retries before the tunnel is declared down (0 to 100).
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Viewing Optical Module Status Table 7-8 IP routing parameters Field Description Enable IP routing Select the toggle button to enable IP routing. Destination IP address Enter the destination IP address. Destination netmask Enter the destination netmask.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Viewing Optical Module Status Figure 7-15 Optical module status page Table 7-9 Optical module status parameters Field Description Serial Number Indicates the serial number. Laser bias current (ONT ANI-ONT-Side Optical Measurements) Laser bias current, measured in uA.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring QoS Figure 7-17 QoS config page (L3 Criteria) Configure the following parameters: Table 7-10 QoS config parameters Field Description Type Select a QoS service layer type from the list: • L2 Criteria •...
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring Upstream (US) Classifier Table 7-10 QoS config parameters (continued) Field Description Protocol Select a protocol from the list. Application Select an application from the list or select Custom Settings and enter an application name.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring Upstream (US) Classifier Click WAN US Classifier in the left pane and select the Policy tab. All classifier policies are displayed in the policy table in the page. Figure 7-18 US Classifier - Policy page...
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring Upstream (US) Classifier Table 7-11 US Classifier - Policy parameters (continued) Field Description IP TOS/DSCP This field is not configurable. All tunnel packets are generated with a default DSCP value (usually 0).
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring Upstream (US) Classifier Table 7-12 US Classifier - Classifier parameters Field Description Interface Select an interface from the list; for example, None, LAN, 2.4G SSID, or 5G SSID. The option None indicates that all interfaces are selected.
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring Upstream (US) Classifier Figure 7-20 US Classifier - Classifier Rules page Configure the following parameters: Table 7-13 US Classifier - Classifier Rules parameters Field Description Policy Select a policy from the list.
Page 123
Configure an XS-2437X-B indoor ONT Nokia ONT WAN Configuration Configuring Upstream (US) Classifier Click Save. The rule is added to the classifier rules table. To delete a classifier rule, click Delete next to the classifier rule entry in the table.
Configure an XS-2437X-B indoor ONT Nokia ONT LAN Configuration Overview LAN Configuration 7.18 Overview This section describes the LAN configuration procedures that can be performed from the following sub-menu options under the LAN menu: Sub-menu Procedure DHCP IPv4 7.19 “Configuring DHCP IPv4” (p. 124) DHCP IPv6 7.20 “Configuring DHCP IPv6”...
Configure an XS-2437X-B indoor ONT Nokia ONT LAN Configuration Configuring DHCP IPv4 Figure 7-21 DHCP IPv4 page Configure the following LAN parameters: Table 7-14 DHCP IPv4 parameters Field Description IPv4 address Enter the IPv4 address of the ONT. Subnet mask Enter the subnet mask of the ONT.
Configure an XS-2437X-B indoor ONT Nokia ONT LAN Configuration Configuring DHCP IPv6 Table 7-14 DHCP IPv4 parameters (continued) Field Description DHCP enable Select the toggle button to enable DHCP. If this toggle button is not enabled, the DHCP functionality cannot be used. you need not configure DHCP start IP address, DHCP end IP address and DHCP lease time if this toggle button is not enabled.
Configure an XS-2437X-B indoor ONT Nokia ONT LAN Configuration Configuring DHCP IPv6 Configure the following parameters: Table 7-16 DHCP IPv6 parameters Field Description LAN prefix configuration Prefix Config Select a prefix configuration option from the list: • Use WAN provided prefix (prefix is obtained from the WAN) •...
Configure an XS-2437X-B indoor ONT Nokia ONT LAN Configuration Configuring DNS Table 7-16 DHCP IPv6 parameters (continued) Field Description Address method Select a address method option from the list: • Stateless Address Autoconfig (SLAAC) • Stateful DHCPv6 Received additional options via Select the toggle button to enable additional options via DHCPv6.
Configure an XS-2437X-B indoor ONT Nokia ONT LAN Configuration Configuring DNS Figure 7-22 DNS page (IPv4) Configure the following parameters: a. Select the DNS proxy toggle button to enable the DNS proxy and click Save. b. Configure the following: 1. Enter the domain name in the Domain Name field.
Configure an XS-2437X-B indoor ONT Nokia ONT LAN Configuration Configuring DNS The DNS table displays the configured domain names and the associated IPv4 address. Click Delete to delete the table entries. ND OF STEPS 7.21.2 IPv6 DNS configuration Click LAN DNS IPv6 in the left pane. The DNS page displays.
Configure an XS-2437X-B indoor ONT Nokia ONT LAN Configuration Viewing LAN Statistics Table 7-18 LAN statistics parameters Field Description SSID name Select an SSID from the list. LAN Wireless info Displays the wireless status, wireless channel, encryption status, received and transmitted bytes and packets and power transmission in mW.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Overview WiFi Configuration 7.23 Overview This section describes the WiFi configuration procedures that can be performed from the following sub-menu options under the WiFi menu: Sub-menu Procedure WiFi networks 7.24 “Configuring WiFi Network” (p. 134) Network map 7.27 “Viewing Network Map, Adding WiFi Points, Renaming WiFi Points and Removing WiFi...
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring WiFi Network Click Add WiFi network + to create a WiFi network. The Add WiFi network page displays. Note: The Add WiFi point option is displayed only when the mesh feature is enabled.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring WiFi Network Table 7-19 Add WiFi network parameters (continued) Field Description 5 GHz Select this option to configure a 5 GHz wireless network. 6 GHz Select this option to configure a 6 GHz wireless network.
Page 137
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring WiFi Network Configure the following parameters: Field Description SSID name Displays the SSID name. Enable SSID Select the toggle button to enable SSID. Band type Displays the band type. SSID index Displays the SSID index.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring Guest Network Field Description WPS Mode Select the required WPS mode from the list: • PBC • STA PIN • AP PIN Select a WPS mode from the list: PBC (Push Button Connect) or STA PIN (Personal Identification Number) or AP PIN (Access Point Personal Identification Number).
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring the WiFi Password Figure 7-28 Guest network page Configure the following parameters: Table 7-20 Guest network parameters Field Description Name Enter the name for guest network. Password Enter a password for guest network.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring the WiFi Password • The password length must be from 8 to 63 characters. • The first character must be a digital number or a letter. • The password must contain all three types of characters: numbers, letters, or special characters.
Click Add WiFi point at the top right corner of the Device Info page. A message displays that it is recommended to use the Nokia WiFi mobile app to add a WiFi point. b. To add a WiFi point using the WebGUI, click Continue with WebGUI.
Page 142
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Viewing Network Map, Adding WiFi Points, Renaming WiFi Points and Removing WiFi Points c. In the Add WiFi point page, enter the serial number and click Add. The WiFi point is displayed in the Detected or Not detected list of the Onboarding Status panel in the Device Info page.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Viewing Network Map, Adding WiFi Points, Renaming WiFi Points and Removing WiFi Points Figure 7-31 <Device> page The WiFi point name can be edited by clicking the edit icon Perform the following steps to change the name of your WiFi point: a.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Viewing Network Map, Adding WiFi Points, Renaming WiFi Points and Removing WiFi Points Figure 7-32 Change the name of your WiFi point page Table 7-21 <Device> parameters Field Description Device name...
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Optimizing WiFi Network 2. Click OK to reboot the ONT. The device reboots and displays the login page. • Reset the device to factory default settings: 1. Click Factory default. A message displays asking if you want to reset the system configuration to the factory default settings.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring Wireless 2.4 GHz Figure 7-33 Advanced settings - 2.4 GHz tab Configure the following parameters: Table 7-22 Wireless 2.4 GHz parameters Field Description Enable Select the toggle button to enable Wireless (2.4 GHz).
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring Wireless 5 GHz Table 7-22 Wireless 2.4 GHz parameters (continued) Field Description Channel Selection Select a channel from the list: • Auto • Manual Note: When changing from automatic to manual channel management, depending on the channel, channel bandwidth, and region, it can take several minutes for the changes to take into effect and for the wireless network to be functional again.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring Wireless 5 GHz Figure 7-34 Advanced settings - 5 GHz tab Configure the following parameters: Table 7-23 Wireless 5 GHz parameters Field Description Enable Select this toggle button to enable WiFi.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring Wireless 6 GHz Table 7-23 Wireless 5 GHz parameters (continued) Field Description Channel bandwidth Select the bandwidth range from the list: • 20 MHz • 40 MHz • 80 MHz •...
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring Wireless 6 GHz Figure 7-35 Wireless 6 GHz page Configure the following parameters: Table 7-24 Wireless 6 GHz Field Description Enable Select this toggle button to enable WiFi. Mode The wireless mode 802.11ax is selected by default.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Configuring Wireless Schedules Figure 7-36 Wireless schedule page Select the Enable Scheduling toggle button to turn off the wireless signal for the configured period. Note: The ONT stores the settings of the current wireless signal and restores with the same settings when WiFi is enabled or disabled until the programmed wireless signal rule is triggered.
Configure an XS-2437X-B indoor ONT Nokia ONT WiFi Configuration Viewing WiFi Statistics If required, click Add new + to add more rules. ND OF STEPS 7.33 Viewing WiFi Statistics Click WiFi WiFi statistics in the left pane. The WiFi statistics page displays.
Configure an XS-2437X-B indoor ONT Nokia ONT Devices Overview Devices 7.34 Overview This section describes how to view device information from the Device menu. 7.35 Viewing Device Information Click Devices in the left pane. The Devices page displays the devices.
Configure an XS-2437X-B indoor ONT Nokia ONT Devices Viewing Device Information Figure 7-39 Device information page - L3 devices The device name can be renamed by clicking the edit icon Perform the following steps to rename the client device: a. To rename the client device, click the Edit icon .
Configure an XS-2437X-B indoor ONT Nokia ONT Voice Configuration Overview Voice Configuration 7.36 Overview This section describes the voice configuration procedures that can be performed from the following sub-menu options under the Voice menu: Sub-menu Procedure Voice setting 7.37 “Configuring Voice Settings” (p. 157) Voice status 7.38 “Viewing Voice Status”...
Configure an XS-2437X-B indoor ONT Nokia ONT Voice Configuration Viewing Voice Status Table 7-26 Voice Setting parameters Field Description Outbound Proxy Enter the outbound proxy details. Outbound Proxy Port Enter the outbound proxy port. Proxy Server Enter the proxy server details.
Configure an XS-2437X-B indoor ONT Nokia ONT Voice Configuration Viewing Voice Status Figure 7-42 Voice status page Table 7-27 Voice status parameters Field Description POTS 1 registration status Indicates if POTS 1 is registered or not. If POTS 1 is registered, the status displays as Registered.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Overview Security Configuration 7.39 Overview This section describes the security configuration procedures that can be performed from the following sub-menu options under the Security menu: Sub-menu Procedure Firewall 7.40 “Configuring the Firewall” (p. 161) MAC filter 7.41 “Configuring the MAC Filter”...
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring the MAC Filter Table 7-28 Firewall parameters Field Description Security level Select the security level from the list: • High: Pre-routing and application services are not supported. UDP Port 8000 can be used to access the services.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring the MAC Filter Figure 7-44 MAC filter page Configure the following parameters: Table 7-29 MAC filter - Ethernet Interface parameters Field Description Ethernet Interface MAC filter mode Select the MAC filter mode from the list: •...
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring the IP Filter Table 7-30 MAC filter - WiFi SSID parameters Field Description WiFi SSID MAC filter mode Select the MAC filter mode from the list: • Blocked • Allowed SSID select Select the SSID from the list.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring the URL Filter Configure the following parameters: Table 7-31 IP filter parameters Field Description Add IPv4 filter or Add IPv6 filter parameters Enable IP filter Select the toggle button to enable an IP filter.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring the URL Filter Click Security URL filter in the left pane. The URL filter page displays. Figure 7-46 URL filter page Note: You cannot use URL filtering for HTTPS. The URL is encrypted when using HTTPS.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring Family Profiles 7.44 Configuring Family Profiles Click Security Family profiles (Parental control) from the left pane. The Family profiles (Parental control) page displays. Figure 7-47 Family profiles (Parental control) page Click Add profile + to add a profile with parental controls.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring Family Profiles In the Select the devices used by <profile> page, select the check box next to the device name and click Save to assign the device to the profile.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring Family Profiles Click a profile to configure parental control for the profile. A page displays the profile parameters. Figure 7-51 Family profile configuration page Select the Internet Access toggle button to enable internet access.
Page 170
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring Family Profiles b. Select the check box next to the device to assign to the profile. c. Click Save. Configure and enable schedules Configure schedules for the profile: a. In the profile page, click the edit icon next to Schedules to create one or more schedules for the profile to set specific days and time slots when the Internet should be turned off.
Page 171
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring Family Profiles 1. Enter the name of the schedule in the Name field. 2. Select the start time, end time, and select the days of the week on which the schedule will be in effect.
Page 172
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring Family Profiles 1. Select the Bedtime, Wake Up time, and select the days of the week on which the bedtime will be in effect. 2. Click Save. The bedtime is created and listed in the Bedtime page.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring DMZ and ALG 1. Select the toggle button next to Filtering to enable filtering to control the profile’s website access. 2. Click Add + to add a website URL to be blocked.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring DMZ and ALG Figure 7-52 DMZ and ALG page Configure the following parameters: Table 7-33 ALG Configuration parameters Field Description ALG Configuration Select the toggle button next to the protocol name to enable the protocols to be supported by ALG: •...
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring Access Control Configure the following parameters: Table 7-34 DMZ Configuration parameters Field Description WAN connection list Select a WAN connection from the list. Enable DMZ Select the toggle button to enable DMZ on the WAN connection.
Configure an XS-2437X-B indoor ONT Nokia ONT Security Configuration Configuring Access Control Table 7-35 Access control parameters Field Description WAN connection list Select a WAN connection from the list. Enable trusted network Select the toggle button to enable a trusted network.
Configure an XS-2437X-B indoor ONT Nokia ONT Advanced Settings Overview Advanced Settings 7.47 Overview This section describes the advanced settings that can be performed from the following sub-menu options under the Advanced settings menu: Sub-menu Procedure Port forwarding 7.48 “Configuring Port Forwarding” (p. 178) Port triggering 7.49 “Configuring Port Triggering”...
Configure an XS-2437X-B indoor ONT Nokia ONT Advanced Settings Configuring Port Triggering Table 7-37 Port forwarding parameters Field Description WAN port Enter the WAN port range. LAN port Enter the LAN port range. Internal client Select a connected device from the list and enter the associated IP address.
Configure an XS-2437X-B indoor ONT Nokia ONT Advanced Settings Configuring DDNS Configure the following parameters: Table 7-38 Port triggering parameters Field Description Open port Enter the open port range. Triggering port Enter the triggering port range. Expiration time Enter the expiration time in seconds.
Configure an XS-2437X-B indoor ONT Nokia ONT Advanced Settings Configuring DDNS Figure 7-56 DDNS page Configure the following parameters: Table 7-39 DDNS parameters Field Description WAN connection list Select a WAN connection from the list. Enable DDNS Select the toggle button to enable DDNS on the WAN connection.
Configure an XS-2437X-B indoor ONT Nokia ONT Advanced Settings Configuring NTP 7.51 Configuring NTP Click Advanced settings NTP in the left pane. The NTP page displays. Figure 7-57 NTP page Configure the following parameters: Table 7-40 NTP parameters Field Description Enable NTP service Select the toggle button to enable the NTP service.
Configure an XS-2437X-B indoor ONT Nokia ONT Advanced Settings Configuring USB Table 7-40 NTP parameters (continued) Field Description Interval time Enter the interval at which to get the time from the time server, in seconds. Allowed values: 0 to 259200 seconds Time zone Select the local time zone from the list.
Configure an XS-2437X-B indoor ONT Nokia ONT Advanced Settings Configuring UPNP and DLNA Configure the following parameters: Table 7-41 USB parameters Field Description FTP server parameters Enable FTP server Select the toggle button to enable an FTP server. By default, FTP server is disabled.
Configure an XS-2437X-B indoor ONT Nokia ONT Advanced Settings Configuring UPNP and DLNA Click Advanced settings UPNP and DLNA from the left pane. The UPNP and DLNA page displays. Figure 7-59 UPNP and DLNA page Select the Enable UPNP/DLNA toggle button to enable UPNP/DLNA. If this toggle button is not enabled, the UPNP and DLNA process will not start.
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Overview Maintenance 7.54 Overview This section describes the maintenance procedures that can be performed from the following sub- menu options under the Maintenance menu: Sub-menu Procedure Change password 7.55 “Configuring the Password” (p. 186) Backup and restore 7.56 “Backing Up the Configuration”...
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Configuring the Password Figure 7-60 Change password page Configure the following parameters: Table 7-42 Change password parameters Field Description Original password Enter the current password. New password Enter the new password as per the password rules.
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Backing Up the Configuration 7.56 Backing Up the Configuration Click Maintenance Backup and restore in the left pane. The Backup and restore page displays. Figure 7-61 Backup and restore page Click Export to export the current ONT configuration to your PC. The configuration filename is config.cfg.
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Restoring the Configuration Figure 7-62 Backup and restore page Click Select and select the previously backed-up configuration file. Click Import to import the configuration file created in 7.56 “Backing Up the Configuration”...
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Upgrading Firmware 7.58 Upgrading Firmware Click Maintenance Firmware upgrade in the left pane. The Firmware upgrade page displays. Figure 7-64 Firmware upgrade page Click Select and select the file for firmware upgrade.
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Configuring SLID Configure the following parameters: Table 7-43 LOID config parameters Field Description LOID authentication LOID Enter the LOID. Maximum number of characters: 24 Password Enter the password. If the password is null, leave this field blank.
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Diagnosing WAN Connections Table 7-44 SLID configuration parameters (continued) Field Description Enter new SLID Enter the new SLID. SLID mode Select a SLID mode from the list. The default is HEX Mode.
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Diagnosing WAN Connections Figure 7-68 Diagnostics page Configure the following parameters. Table 7-45 Diagnostics parameters Field Description Protocol Select a protocol from the list: • IPv4 • IPv6 WAN connect list Select a WAN connection to diagnose from the list.
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Diagnosing WAN Connections Table 7-45 Diagnostics parameters (continued) Field Description Traceroute Select this toggle button to enable traceroute. Ping try times Enter the number of ping attempts. This field is enabled only if you select the Ping toggle button.
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Viewing Log Files 7.62 Viewing Log Files Click Maintenance Log in the left pane. The Log page displays. Figure 7-71 Log page Configure the following parameters: Table 7-46 Log parameters Field Description...
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Generating a delta configuration file Click Save. The log file is displayed at the bottom of the page. Click Export log to download the log file to your PC. The filename of the log is onu_info.log.
Page 198
Configure an XS-2437X-B indoor ONT Nokia ONT Maintenance Generating a delta configuration file convert the file to .tar format before downloading it to the ONT. Note: For merging the downloaded delta config, the previously downloaded delta file must be renamed by adding “CFG” at the start of the filename and .cfg extension to be added to the delta config file (CFG_*.cfg) to upload the file successfully in Delta CFG...
Configure an XS-2437X-B indoor ONT Nokia ONT Troubleshooting Troubleshooting counters Troubleshooting 7.64 Troubleshooting counters The Troubleshooting counters feature enables service providers and end users to monitor the performance of their broadband connection for about 10 seconds from the time the test is triggered.
Configure an XS-2437X-B indoor ONT Nokia ONT Troubleshooting Speed Test Table 7-47 Troubleshooting counters parameters (continued) Field Description WAN Status Displays the WAN status: • Up • Down Troubleshoot counters US throughput snapshot This test is used to determine the upstream throughput/speed.
Configure an XS-2437X-B indoor ONT Nokia ONT Troubleshooting Speed Test Figure 7-74 Speed test page Table 7-48 Speed test parameters Field Description TR-143 server settings Upload test server URL Enter the Upload test server URL. Number of upload connections Enter the Number of upload connections.
Page 203
Configure an XS-2437X-B indoor ONT Nokia ONT Troubleshooting Speed Test Table 7-48 Speed test parameters (continued) Field Description Test mode Select a Test mode: • Time based • File based Upload file size Displays the file size in MB. This parameter is visible only if the Test mode is File Based.
Note: This feature is supported for use with the 7360 ISAM FX and the 7342 ISAM FTTU. When ONT is deployed, it is recommended to use the following operator IDs: • ALCO - Voice managed through OMCI (OMCIv1(nokia proprietary or OMCV2(Standard OMCI G.988 specs)) •...
The Nokia defined index for the Voice XML file is: "XML" 8.3.1 Filename conventions Nokia provides the raw configuration files, which must be saved by the operator in a TAR file to be uploaded. TAR file names must be unique.
Page 208
XMLXXXXXX1 Configure equipment interface pland-cfgfile2=XMLXXXXXX2 and dnload-cfgfile2 XMLXXXXXX2 Although the OLT permits the above two steps without reporting an error, Nokia does not recommend executing them, because the ONT may exhibit unexpected behavior. f. If pland-cfgfileX=Auto and dnload-cfgfileX= Auto The OLT will download the XML file from "sw-ctr-list" (configure equipment ont sw-ctrl)
Page 210
(Config, Delta Config, Voice XML and WebGUI config), allowing to download and install it as a single package into the ONT. This is specially useful in deployment scenarios with third party OLTs, which do not support Nokia configuration files download via OMCI. Note: 1.
Need help?
Do you have a question about the XS-2437X-B and is the answer not in the manual?
Questions and answers