1736/100C
Read the warnings contained in this document carefully as they provide important information regarding safe installation,
use and maintenance.
GENERAL WARNINGS
• The device must be used only for the use for which it was expressly designed, that is for powering video intercom systems.
• It has been designed to comply with current regulations. Any other use is to be considered improper. The manufacturer
cannot be held responsible for any damage resulting from improper and unreasonable use.
• The execution of the system must comply with current regulations. All the devices making up the system must be intended
exclusively for the use for which they were designed.
• Provide a suitable isolation and protection switch upstream of the devices with a contact opening distance of at least 3mm.
• The device must be installed inside an electrical panel or cabinet.
• Before connecting the equipment, make sure that the plate data corresponds to that of the distribution network.
• After removing them from the packaging, check the integrity of the equipment. Packaging elements (plastic bags,
expanded polystyrene, etc.) must not be left within the reach of children, as they are potential sources of danger.
• Do not block the ventilation or heat exhaust openings or slots.
• Do not install the equipment in environments exposed to rain or humidity. In these cases, use special containers.
• Before carrying out any cleaning or maintenance operation, disconnect the device from the electrical power supply by
turning off the system switch.
• Do not use spray cleaning products.
• In the event of a fault and/or malfunction of the device, turn off the power using the main switch and do not tamper with it.
• In the event of infiltration of liquids or objects inside the device and for any repairs, we recommend contacting the technical
assistance center indicated by the manufacturer.
• Do not use extension cables for the power supply cable.
• The installer must ensure that user information is present on all installed devices, including this document.
• Failure to comply with the above may compromise the safety of the appliance.
• Place the elements on vertical and smooth supports, respecting all the instructions provided in the product manual
downloadable from the website www.urmet.com.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept all interference received, including interference that may cause undesired operation.
15.105 Information to the user statements:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical
and electronic equipment (WEEE).
The crossed-out wheelie bin symbol on the equipment or its packaging indicates that the product at the end of its
useful life must be collected separately from other waste.
Therefore, any products that have reached the end of their useful life must be given to waste disposal centres
specialising in separate collection of waste electrical and electronic equipment. As an alternative to autonomous
disposal, the device you want to dispose of can be given back to the retailer at the time of purchasing new similar
equipment. At electronic product retailers with a sales area of at least 400 m2, it is possible to return, without any obligation
to buy, electronic products to dispose of with dimensions below 25 cm free of charge. The separate collection for delivery
the equipment to recycling, to treatment and environmentally compatible disposal helps avoid possible negative effects on
the environment and health and promotes the reuse and/or recycling of materials that make up the equipment.
ENGLISH
Need help?
Do you have a question about the 1736/100C and is the answer not in the manual?
Questions and answers