Sharp ELSI MATE EL-CC12D Operation Manual

ELECTRONIC CALCULATOR
PRINTED IN CHINA
OPERATION MANUAL
BEFORE USE
• Do not press too hard against the LCD panel
because it contains glass.
• Never dispose of the battery in a fire.
• Keep battery out of reach of children.
• Since this product is not waterproof, do not use it
or store it where fluids, for example water, can
splash onto it. Raindrops, water spray, juice,
coffee, steam, perspiration, etc. will also cause
malfunction.
• Please press if you see no indication.
• This product, including accessories, may change
due to upgrading without prior notice.
SHARP will not be liable nor responsible for any
incidental or consequential economic or property
damage caused by misuse and/or malfunctions
of this product and its peripherals, unless such
liability is acknowledged by law.
1. Before starting calculations, press to clear (zero-clear).
2. The position of any switch that is not specificaly designated, may be set to any position.
3. For expressing calculation examples, only the symbols that are required for explanation are mentioned.
4. Example procedures are listed in following manner unless otherwise specified.
(EL-CC12GP/CC14GP)
DECIMAL POINT ASSIGNMENT SWITCH
"F" position: Set the decimal point to "floating" point.
"4,3,2,0" positions: The decimal figures can be set to the respective numbers.
"A" position: Assigns Adding mode (sets the decimal at 2). In the case of addition/subtraction,
the decimal point will be
placed at 2 automatically. If is registered, or in case of non-additive/non-subtractive
calculation, this function will not be applicable.
(EL-CC12GP/CC14GP)
ROUNDING SELECTOR
Specifies the handling of the digit immediately below the position set by the decimal selector.
(For example, if the decimal selector is set to 3, then the fourth decimal will be rounded.)
" " position: The answer will be rounded up.
"5/4" position: The answer will be rounded off.
" " position: The answer will be rounded down.
* While the decimal selector is set to the "F" (i.e., floating) position, or if the decimal place cannot be
determined (preliminary calculation results, for instance), the answer will always be rounded down
regardless of the setting above.
STATUS DISPLAY AND COUNTER
(1) 23×2÷4＝11.5
(EL-CC12GP/EL-CC14GP: )
(2) (3)
001
23
001
2 002
CHECK & CORRECT
• The maximum number of calculation steps (operators and numerical values) that can be stored is 300.
And when 300 steps are reached, correction/insertion/deletion cannot be performed.
• Symbols when replaying may be different from those when calculating
(ex. " M " symbol of memory calculations is displayed as recall memory or clear memory when
replaying. ).
• In some calculations, correction/insertion/deletion cannot be performed.
EL-CC12D
EL-CC12G
EL-CC12GP
EL-CC14GP
MODEL
20BSC(TINSEA306EHZZ)
20ESC(TINSEA306EHZZ)
ENGLISH
SPECIFICATIONS
Type: Electronic calculator
Operating capacity:
[EL-CC12D/
EL-CC12G/CC12GP] 12 digits
[EL-CC14GP] 14 digits
Power supply: Built-in solar cell and Alkaline
manganese battery (1.5V
(DC) LR44 or equivalent × 1)
Operating time: Approx. 2 years
(varies according to (with 1 hour of daily use, using
use and other factors) the alkaline manganese
battery only)
Automatic Power-off: Approx. 7 min.
Operating temperature: 0°C - 40°C (32°F-104°F)
Dimensions:
[EL-CC12D]
132 mm(W) × 166 mm(D) × 30 mm(H)
[EL-CC12G/
EL-CC12GP/CC14GP]
158 mm(W) × 198 mm(D) × 32 mm(H)
Weight:
(battery included)
Approx. 169 g
[EL-CC12D]
Approx. 236 g
[EL-CC12G]
Approx. 240 g
[EL-CC12GP]
Approx. 244 g
[EL-CC14GP]
Accessories: Alkaline manganese battery
(installed), Operation manual
OPERATIONS
002
0.
003
23. 4
004
23.
G
2.
• Pressing will clear all memories, including stored calculation steps. And if the battery is consumed
largely, all memories are also cleared.
• At the time of correction/insertion/deletion, if decimal point settings or rounding settings or tax rate of
stored each calculation step are changed, all stored calculation steps will be recalculated with the
changed settings.
• After starting correction/insertion (pressing
before pressing
• If an error occurs ("E" symbol appears), all stored calculation steps will be cleard.
• "BUSY" may be displayed during recalculation.
AUTO REPLAY
• Auto Replay starts by pressing
Auto Replay stops by pressing
to resume.
(1) (400−80＋500)×3＝2460
(EL-CC12GP/EL-CC14GP:
(2)
400 80
005
500 3
G
001
002
/ PREVIOUS / NEXT
• Each time is pressed, calculation formulas are recalled in the order they are entered, while each
time is pressed, calculation is recalled in the order of its answer.
(1) (400−80＋500)×3＝2460
(EL-CC12GP/EL-CC14GP:
(2)
400 80
005
500 3 G
005
004
CORRECT
(1) (400−80＋500)×3 → (400−100＋500)×3＝2400
(EL-CC12GP/EL-CC14GP:
(2)
400 80
005
500 3
001
002
002
002
100
INSERT
(1) (400−80＋500)×3 → (400−80＋500)÷2×3＝1230
46.
4.
(EL-CC12GP/EL-CC14GP:
(2)
11.5
400 80
005
500 3
G
005
004
004
004
/ ), the entered value is canceled by pressing
/ to set the entered value.
and you can recall a calculation formula automatically.
during Auto Replay and pressing
)
(3)
2'460.
AUTOREPLAY
400.
AUTOREPLAY
80.
)
(3)
2'460.
REPLAY
2'460.
REPLAY
3.
)
(3)
(
2'460.
G
REPLAY
400.
REPLAY
80.
REPLAY CORRECT
80.
REPLAY CORRECT
100.
)
(3)
2
2'460.
(
REPLAY
2'460.
REPLAY
3.
REPLAY INSERT
0.
REPLAY INSERT
0.
EL-CC12D/CC12G/CC12GP/CC14GP(LC1)-1
again starts Auto Replay
003
AUTOREPLAY
500.
004
REPLAY
3.
005
REPLAY
2'460.
003
REPLAY
500.
002
REPLAY
80.
001
REPLAY
400.
REPLAY
002
100.
)
003
REPLAY
500.
004 REPLAY
3.
005
REPLAY
2'400.
004 REPLAY INSERT
2.
004
REPLAY
2.
)
005
REPLAY
3.
006
REPLAY
1'230.