Advertisement
Advertisement
Table of Contents
Related Manuals for JUNKKARI W600
Summary of Contents for JUNKKARI W600
- Page 1 Junkkari W600/700 iSOBuS Manual...
- Page 2 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS 1 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS The Junkkari ISOBUS ECU is programmed for the 3724 control unit manufactured by Epec Oy. The ISOBUS functionality level is TC-GEO. 1.1 funCtiOnS, Junkkari W600 anD W700 1. Driving speed (km/h) 2.
- Page 3 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS 11. Wing locks • With the wings in the transport position, the left or right side can be locked to stop it from lowering. • With the wings down, the left or right side can be locked to stop it from raising.
- Page 4 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS 1.3 DiSplaYED funCtiOnS 1. Driving speed 2. Surface area counters 3. Tramlines 4. Bout marker 5. Pause 6. Fertiliser remote adjustment 7. Seed remote adjustment 8. Wing hopper level sensors 9. Pole lift 10. Half-width seeding...
- Page 5 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS 1.4 DiSplaY alarMS, WarninGS, inDiCatOr liGhtS anD ButtOnS 1. Wing hopper level sensors 2. Hopper screw 3. Fertiliser and seed shaft speed difference 4. Wing hopper level sensors OFF 5. Pole lift 6. Half-width seeding...
-
Page 6: Table Of Contents
Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS 1.5 frOnt paGE ButtOnS Rivimerkkarivalokko 2.5.1 Lannoite/siemensäätövalikko 2.5.2 Ruiskutusurarytmin vaihto 2.5.3 Pause päälle/pois 2.5.4 Asetuksiin 2.5.5 Diagnostiikkanäyttöön 2.5.6 Bout marker menu 2.5.1 Fertiliser/seed hopper menu 2.5.2. Tramline rhythm change 2.5.3 Pause ON/OFF 2.5.4 Settings 2.5.5. - Page 7 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS Please note that 2.5.1 Huomioi että ikoni is only displayed if the Takaisin päävalikkoon Back to main menu 2.5.1 näkyy vain jos machine is equipped koneeseen on asen- with bout markers. nettu rivimerkkarit Rivimerkkarit pois päältä...
-
Page 8: Tramline Rhythm Change
Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS 1.5.3 traMlinE rhYthM ChanGE Note that icon 2.5.3 is only displayed if the machine is equipped with tramline switches. Ruiskutusurarytmin vaihto Tramline rhythm change The +1 button increases the counter figure by one. Note that when the display shows two of the same number, e.g. - Page 9 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS Takaisin päävalikkoon Back to main menu Lannoitekiertokoe ja Fertiliser calibration and step adjustment % 2.5.5.2 säätöaskellus % 2.5.5.2 Siemenkiertokoe ja sää- Seed calibration and step adjustment % 2.5.5.3 töaskellus % 2.5.5.3 Ruiskutusura asetukset Tramline settings 2.5.5.4 2.5.5.4...
-
Page 10: Asetuksiin
Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS Fertiliser calibration: Lannoitekiertokokeen teko: 1. Set the target kg/ha. 1. Anna haluttu tavoiteltu määrä kg/ha 3. Press Start Test to set the 3. Start test säätää sylinterit oletettuun cylinders to the default position for asemaan jossa varsinainen kiertokoe the calibration. - Page 11 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS Once you have saved the rotation test results, the adjustment cylinder will make any corrections. The correction needed is shown as a percentage. After this, carry out one or two rotation tests to ensure that the results correspond to the desired kg/ha volume. When the adjacent menu reads 0–4%, the cylinder is located accurately and you can start seeding.
- Page 12 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS 1.5.10 arEa COuntEr rESEt Press the area counter reset button to enter a menu where you can reset the ha1 and ha2 counters. Back to main menu ha1 surface area counter reset ha2 surface area counter reset...
- Page 13 Junkkari iSOBuS ECu tEChniCal SpECifiCatiOnS 1.5.11 DiaGnOStiCS SCrEEn The diagnostics screen button opens a dashboard for inspecting the status of different functions and sensors. Seed feed shaft speed difference Hopper screw Fertiliser feed shaft speed pulses speed difference Driving speed...
Need help?
Do you have a question about the W600 and is the answer not in the manual?
Questions and answers