Related Manuals for Cheyenne ENGEN
Summary of Contents for Cheyenne ENGEN
- Page 2 EnGen...
- Page 3 EnGen EnGen...
- Page 4 Charger Charging Battery 2x Battery EnGen RUN/STOP Adjust Display Battery Output Housing Connector Control cable in Case Button Button State Voltage Handpiece Unit UP/DOWN *The power supply needed for use is not included in the scope of delivery. You can purchase this accessory to match your product from your local specialist retailer (see chapter 4.2).
- Page 5 ISINFECTING THE DEVICE ............15 ETTING THE STITCHING FREQUENCY ........... 15 TART OR STOP THE TATTOO MACHINE ..........15 WITCHIN THE DEVICE TO STANDBY MODE ..............15 HANGING DEVICE SETTINGS CLEANING AND MAINTAINING THE PRODUCT ........ 15 ..............16 ATERIAL COMPATIBILITIES EnGen...
- Page 6 Remedy danger • Workplace safety regulations and legal requirements for tattooing Signal Meaning word Indicates a hazard that will definitely lead to death or to Hazard serious injury if the hazard is not avoided EnGen...
- Page 7 ► Children must be instructed not to play case of accidental contact, rinse with ► Read and observe the safety instructions with the device. water. If the liquid gets into your eyes, instructions operating seek additional medical attention. instructions for the device. Failure to EnGen...
- Page 8 (chapter 4.2) batteries can cause injury and cause fire. months to avoid leakage or performance comply with operating, If other batteries are used, Cheyenne loss. transport storage conditions assumes no liability or warranty. ► Only use the charging cable included (chapter 8).
- Page 9 The EnGen in combination with a suitable agent. When selecting an appropriate the chapter 7. tattoo machine can be used to tattoo...
- Page 10 3 Scope of delivery Any use of the device or its accessories that is not described in these instructions for use Temperature limit 1 EnGen or non-compliance with the operating 1 Container with two batteries conditions is considered improper use.
-
Page 11: Product Information
Power consumption 6 W max. during tattooing. Output voltage Output voltage 4,7 V – 12,5 V The EnGen can be used to control the Permanent tattoo machine's piercing frequency using Operating mode operation the UP/DOWN adjustment button. The 73 mm x 39 mm x... - Page 12 • Are there any visible signs of external transport, for example, condensate may damage (e.g. loose bent +10°C to +35°C form inside, which may cause damage to Ambient temperature components)? +50°F to +95°F the electronics. Relative humidity 30 % to 75 % EnGen...
- Page 13 Suitable are for example: ► Never transport the device loose in a • the USB power adapter from your bag, as metal parts (e.g. keys) can cause smartphone or tablet a short circuit. • the power supply from recommended accessories EnGen...
- Page 14 ► Push the control unit into the housing as approved according to the regulations far as it will go. in your country. ► Plug the device with the front coupling ► Note list recommended onto the connection of the tattoo disinfectants in chapter 7.1. machine. EnGen...
- Page 15 The device switches to standby mode. Damage caused by liquid ► Hold the tattoo machine firmly before If cleaning agents or disinfectants get starting it or place it in a suitable holder. inside the device a short circuit may occur EnGen...
- Page 16 • Ethanol disinfectants, observe the material disinfectant. compatibility (chapter 7.1). • Most inorganic salts and their aqueous solutions (e.g. sodium chloride, calcium chloride, magnesium sulphate) The anodized aluminium components and seals of the machine are not resistant to: EnGen...
- Page 17 Relative humidity 30 % to 75 % Atmospheric 500 hPa to 1060 hPa pressure ► Never transport a tattoo machine with the device plugged in. Disconnect the machine and device before transport. ► Before transporting the device, remove the battery. EnGen...
- Page 18 Attention symbol appears! stand-by mode. tailer or the responsible au- thorities to learn about appli- ► Contact your specialist retailer if the cable regulations. problem persists. ► For safety reasons, you must restart the motor following the instructions in chapter 6.3. EnGen...
- Page 19 2 years for malfunctions caused in the following situations: material defects defects workmanship. • Start attempt, but no machine is connected. We do not provide warranty cover in respect of the following types of damage: EnGen...
- Page 20 Blohmstr. 37–61 12307 Berlin, Deutschland Description oft he machine Product description: Batterypack-operated control unit for tattoo handpieces Product name: EnGen Article description: B80401 The manufacturer declares that the above-mentioned product conforms to the provisions below: RoHS-Directive 2011/65/EU Electromagnetic Compatibility Regulations 2016...
- Page 21 – Part 2: Immunity – Product family standard EN 62233:2008 + AC:2008 Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure Berlin, 30.09.2023, Jörn Kluge Signature of the CEO or his authorised representative Original EnGen...
Need help?
Do you have a question about the ENGEN and is the answer not in the manual?
Questions and answers