Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Viatom Oxyfit PO6
Summary of Contents for Viatom Oxyfit PO6
- Page 1 Oxyfit Pulse Oximeter User Manual...
- Page 2 Contents User Manual......English 1-16 Mode d'emploi.......Français 17-34 Manuale d'Uso......Italiano 35-52 Manual de usuario....Español 52-70...
-
Page 3: Download App
English Download App Download the ViHealth App from iOS App Store or Google Play Store, or scan the QR code. Notice: if you have installed the App before, please update it to the latest version. 1. Introduction 1.1.Intended use This Pulse Oximeter is intended to be used for measuring, displaying and storing adult' s pulse oxygen saturation (SpO2), pulse rate of adults in home or healthcare facilities environment. - Page 4 Do not place this device in pressure vessels or gas sterilization device. Do not dismantle the device, as this could cause damage or malfunctions or impede the operation of the device. Consult your doctor immediately if you experience symptoms that could indicate acute disease.
- Page 5 The functional tester cannot be used to assess the accuracy of the SpO2 sensor or a device. The device has no alarm system. Continuous use for a long time may cause allergies, redness, blistering or burns. Check the wearing position every 6-8 hours.
- Page 6 Type BF Applied Part No alarm system MR unsafe Indicates that the product is protected against solid foreign objects of 12,5 mm Ø and greater; and protected against IP22 vertically falling water drops when enclosure tilted up to 15°. Indicates that the product complies with the EU Medical Device Regulations(Regulation (EU) 2017/745) Article 120, Annex II of 93/42/EEC and Reg...
- Page 7 Humidity limitation Atmospheric pressure limitation 1.4.Unpacking Device User Manual Charging Cable 2. Overview...
-
Page 8: Using The Device
3. Using the Device 3.1.Charging Charge the battery before using. Connect the device to computer USB or USB charging adapter with USB cable. After fully charged, the device will power off automatically. 3.2.POWER ON/OFF POWER ON: Wear the device, it will turn on automatically. POWER OFF: The device turns off automatically in a moment after you take it off. - Page 9 Notice: If the working time is less than 30 seconds, the data will not be saved. Please avoid excessive motion. Please avoid strong ambient light condition. 3.5.Stop working & sync data Take off the device, the countdown will begin. (If the working time is less than 30 seconds, there will be no countdown) During the countdown, if you wear...
-
Page 10: Maintenance
It may be caused by: Excessive movement; Poor signal, finger is too cold; Usually, the readings will recover in a few seconds when at rest. 3.8.Bluetooth Connection The device Bluetooth will be enabled automatically after it’s turned on. To establish a Bluetooth connection, 1) Keep the device on. -
Page 11: Specifications
Solution Device Battery may be low. Charge battery does not and try again. turn on Device might be Please contact or no damaged. your local response distributor. Software exception Press and hold the key for 8 seconds. The app The Bluetooth of Turn on the cannot your phone is off. - Page 12 Electro-magnetic Group I, Class B compatibility Degree of dust & IP22 water resistance Weight 28 g Size 38×30×38 mm 3.7Vdc, Rechargeable Battery Lithium-polymer Charge DC 5V, 1A requirement Charge time 2-3 hours Battery life 12-14 hours for typical use Wireless Bluetooth 4.0 BLE Oxygen level 0% to100%...
- Page 13 Frequency range 2.402 – 2.480 GHz Max RF power -10 dBm Expected service 5 years life 7. Appendix EMC The equipment meets the requirements of IEC 60601-1- 2:2014. Table 1 Guidanc e and manufacturer ’s declarati on -electromagnetic emission The Pulse Oximeter i s intended for use in the electromagnetic environment specified below.
- Page 14 Guidanc e and manufacturer ’s declarati on-electromagnetic emission The Pulse Oximeter i s intended for use in the electromagnetic environment specified below. The customer or the user of the Pul se Oximeter should assure that it is used in such an environment. Complia Electromagneti Immunity...
- Page 15 voltage (60% dip in UT) for 5 variations cycles on power <70% UT supply (30% dip in UT) for 25 input lines cycles IEC61000- <5% UT 4-11 (>95% dip in UT) for 5 Power frequency magnetic fields Power shoul d be at frequency levels (50Hz/60Hz...
- Page 16 any part of The Pul se Oximeter, including cables, than the recommended separati on distance Conducte 3 Vrms calculated from d RF 150 kHz IEC61000 to 80 equation applicable to the -4-6 frequency of the transmitter. Recommended separati on distance 3 V/m d=1.2 P 3 V/m...
- Page 17 Electromagnetic propagation i s affected by absorption and reflection from structures, objects and people. a: Field strengths from fixed transmitters, such as base stations for radio (cellular / cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
- Page 18 Shenzhen Viatom Technology Co., Ltd. 901, Building West, Lepu Tower, No.66 Xingke Road, Xili Community, Xili Street, Nanshan District, 518055 Shenzhen, Guangdong P.R. China www.viatomtech.com MedNet EC-REP GmbH Borkstrasse 10, 48163 Muenster, Germany Tel: +49 251 32266-0 Fax: +49 251 32266-22 Email: contact@mednet-ecrep.com...
Need help?
Do you have a question about the Oxyfit PO6 and is the answer not in the manual?
Questions and answers