elero RolTop/D+ 915 Operating And Installation Instructions

Roller shutter drive RolTop/D+ 868/915

Table Of Contents

Operating and installation
1
instructions
2 General for instructions
2.1 Standards and Directives
2.2 Intended use
2.3 Foreseeable misuse
2.4 Warranty and liability
2.5 Customer service of the manufacturer
3 Safety
3.1 General safety instructions
3.2 Layout of the safety guidelines
4 Product description
5 Assembly
5.1 Mechanical fastening
5.2 Electrical connection
5.3 Connection example,
RolTop/D+ 868 230 V/50 Hz
5.4 Initial operation
5.4.1 Connection for cable assembly
5.4.2 Connection for radio
(transmission operation)
5.4.3 Changing / Deleting the end positions
5.4.4 Programme or delete further curtain
positions
5.5 Programming the transmitter
5.6 Programming (additional) transmitter
6 Troubleshooting
7 Maintenance
8 Repair
9 Manufacturer's address
10 Disassembly and disposal
11 Notes on the EC declaration of conformity
12 Technical data and dimensions
12.1 RolTop/D+-S-868
12.2 RolTop/D+ M-868
Roller shutter drive RolTop/D+ 868
1 Operating and installation
1
instructions
1
Please keep these operating instructions for later use, to be
available throughout the life of the product!
1
The German manual is the original version.
1
All other documents represent the language translations of
the original text.
2
All rights in the case of a patent, utility model or ornamental
2
design registration are reserved.
2 General for instructions
2
2
The content structure is based on the life cycles of the elec-
tric motor drive (hereinafter referred to as "Product").
2
The manufacturer reserves the right to make changes to
the Specifications stated in these Operating Instructions
2
at any time. These may, in individual cases, be different
from the respective product version, however the functional
3
information will not undergo significant changes or become
invalid. The current version of the Specifications may be
3
requested from the manufacturer at any time. No claims
3 may be asserted against the manufacturer as a result of the
preceding sentence. Deviations from text or picture state-
4
ments are possible and depend on the technical develop-
ment, features, and accessories of the products. Deviating
information on special versions will be explained by the
manufacturer in the sales documentation. Other information
4
shall remain unaffected by these provisions.
4
2.1 Standards and Directives
4
During the design process, the basic health and safety
requirements of the applicable laws, Standards and Direc-
tives were complied with. The safety is confirmed by the
4
declaration of conformity (see "Declaration of Conformity").
All safety information in these Operating Instructions refer
5
to the laws and regulations currently applicable in Germany.
All instructions in the Operating Instructions shall be ob-
served without limitation and at any time. Beside the safety
5
instructions contained in these Operating Instructions, the
provisions for accident prevention, environmental protection
5
and occupational safety, which are applicable for the op-
erating site, must be observed. Provisions and Standards
5
for the safety rating can be found in the EC Declaration of
Conformity
5
2.2 Intended use
6
The product is intended for use in façade engineering to
drive electrically powered roller shutters.
6
The determining factor for the drive is the elero drive com-
6
putation program
(http://elero.com/drive-calculation).
6
Further fields of application have to be arranged with the
manufacturer, elero GmbH Antriebstechnik (see Address).
6
The operator will be solely responsible for damages result-
6
ing from improper use of the product. The manufacturer
cannot be held liable for personal or material damages
8
caused by misuse or procedural errors, and by improper
operation and commissioning.
8
The product may be operated only by trained and author-
ized personnel under observance of all safety.
138172206_EN_0614