Subscribe to Our Youtube Channel
Related Manuals for Xinje DPL-708A
Summary of Contents for Xinje DPL-708A
- Page 1 DPL-708A Stepper Driver User Manual WUXI XINJE ELECTRIC CO., LTD. DLC03 20150909 1.0...
-
Page 3: Table Of Contents
Content 1. Summary ................................2 1-1. Characteristic ........................2 1-2. Application ......................... 2 1-3. Electric characters ......................2 2. Operation Guide ..............................3 2-1. Safety ..........................3 2-2. Attention ........................... 3 2-3. Installation ......................... 3 3. Common Terminals ..............................4 3-1. -
Page 4: Summary
1. Summary DPL-708A is a new digital two-phase stepping motor driver of our company. The user can set the subdivision within 200 ~ 40000 and any current value within the rated current. The pure sine wave current control technology is adopted to make the motor run smoothly with small noise, which can meet the application needs of most occasions. -
Page 5: Operation Guide
Storage temperature -20℃~65℃ Dimension 150mm×94mm×57mm 2. Operation Guide Please read the following suggestions carefully before you install the driver. 2-1. Safety The driver is authorized to be installed and operated by the professional staff. Don’t turn on the power before connecting to the motor. ... -
Page 6: Common Terminals
3. Common Terminals 3-1. Control signal terminals 3-1-1. Description of Control signal terminals Signal Function Description Pulse control The rising edge is effective; motor moves one step at the PUL+ signal rising edge of pulse. PUL high voltage is 24V, low PUL- voltage is 0~0.5V. -
Page 7: Input Circuit
The ENA (enable) signal should turn to high-level at least 5s before DIR (direction) signal. Ensure the DIR (direction) signal is built at least 5μs before falling edge of PUL (pulse) signal. The width of pulse should be more than 1.2μs ... -
Page 8: Power Terminals
above 8mA. Optical coupler current limiting resistor is built in stepper driver. It is common to supply all the control signals with +24V. 3-2. Power Terminals 3-2-1. Description of Heavy-current terminal Terminal Function Description AC or DC Between the minimum and maximum supply voltage, AC, DC the recommended value should be used Phase A of motor... -
Page 9: Selection Of Input Voltage And Output Current
3-2-4. Selection of input voltage and output current 1. Selection of driver input voltage Generally speaking, the higher the power supply voltage is, the greater the torque is when the motor is at high speed, and the step lost can be avoided when the motor is at high speed. -
Page 10: Function Setting
their own needs to achieve satisfactory results. 4-wire motor: the output current is set equal to or slightly less than the rated current of the motor; High torque mode of 6-wire motor: the output current is set to 50% of the rated current of motor single polarity connection method;... -
Page 11: Pulse Per Revolution Setting
Half current means that when the motor stops, the force of the stator locking the rotor will be reduced to half, which can reduce the heat output and energy saving of the motor. 1: For the equipment with small reaction force (most of which are of this structure), please use half current or even enable motor. -
Page 12: Protection Function
Note: after the above protection circuit acts, the driver cannot work normally. Only after the fault is eliminated, power on again and the power indicator turns green, the driver can be recovered. 4. Dimension and wiring 4-1．Dimension The dimension of DPL-708A is shown as below: Unit: mm... -
Page 13: Installation
57.0 94.0 45.0 18.0 ALM/PWR DPL-708A PUL+ CN1(SW1-SW3): PUL- DIR+ 2.00A 2.40A 2.57A 3.08A DIR- 3.14A 3.77A ENA+ 3.71A 4.45A ENA- 4.28A 5.14A 4.86A 5.38A 5.43A 6.52A 6.00A 7.20A CN1(SW5-SW8): 1600 3200 6400 12800 25600 1000 2000 4000 5000 8000... -
Page 14: Fault And Solution
Note: when wiring, the user shall follow the principle of separating power cable (motor phase cable, power cable) and weak current signal cable to avoid interference of control signal. 5. Fault and solution Malfunction Causation Solution Something wrong with the power The power light doesn’t Check the power supply supply... -
Page 15: Motor Selection
6. Motor Selection DPL-708A is suitable for 4,6,8-wire two-phase and four phase hybrid stepping motor, and the step angle of 1.8 degree and 0.9 degree can be applied. But in order to make the motor run best, it is usually necessary to choose a suitable motor and driver. - Page 16 WUXI XINJE ELECTRIC CO., LTD. 4th Floor, Building 7th, No.100 Dicui Rd, Wuxi, China Tel: 86-0510-85134139 Fax: 86-0510-85111290 www.xinje.com...
Need help?
Do you have a question about the DPL-708A and is the answer not in the manual?
Questions and answers