Xinje XD-4DA-V-ED Quick Start Manual

Extension ED module
XD-4DA-V-ED
Fast manual
Thanks for purchasing XINJE XD series PLC and extension module. This manual will
introduce the electric features and using method of XD series extension ED module. Please
read this manual carefully before using the products, make sure the wiring operation is safe.
Features of analog extension module
XD-4DA-V-ED
 4 channels analog output: voltage output mode, 0~10V or 0~5V.

10-bit high precision analog output.
 As the special function ED module of XD, XD series PLC can connect 1 XD-
4DA-V-ED module.
Safety precautions
 Control system design attentions
Dangerous!
 Make sure design the safety circuit, to ensure that the control system can still work
safety when the external power supply cut off or PLC broken.
 Make sure set emergency braking circuit, protection circuit, interlock circuit of forward-
reverse running in PLC external circuit and upper-lower limit switch to prevent from
machine damage.
 In order to make the equipment safe operation, please design external protection circuit
for important output signal.
 PLC CPU will close all the output when detecting the system error; the output will lose
control when the PLC circuit has problem. Please design suitable external control circuit
to ensure the device working normally.
 If the PLC relay or transistor unit is broken, the output cannot be ON or OFF.
 The PLC is designed for indoor environment, the lightning protection must be installed
in the power supply system to avoid PLC and other device damage.
 Installation and wiring attentions
Dangerous!
 Do not use the PLC in the following environment: dust, soot, corrosive gases,
flammable gas, high temperature, condensation, vibration, impact, lightning, fire.
 Do not let the metal scrap and wire head drop into the ventilation hole of PLC, otherwise
it will cause fire or error operation.
 Do not cover the ventilation hole of PLC, otherwise it will cause fire, error operation.
 The I/O wiring must be fixed enough, otherwise the bad contactor will cause fault.
Attention!
 It can use external power supply for extension module DC24V power.
 Please use shield cable for high frequency I/O wiring to avoid interference.

Run and maintenance
Dangerous!
 Please connect all the cable include PLC, extension module and BD board after shutting
down the power supply.
 Please operate as the manual for online operation, forced output, RUN, STOP.
Attention!
 Please discard the product as industrial waste.
 Make sure cut off the power supply when installing or uninstalling the extension card.
Product information
 Naming rule
XD– 4 DA - V - ED
① ② ③ ④ ⑤
① Product series XD: XD series extension module
Analog output channel: 4: 4 channels
②
③ Analog output DA: analog output
④ I/O type V: voltage type for output
⑤ Module type ED: left extension ED module
 Basic parameters
XD series PLC can connect 1 extension ED module, the type is not limited.
Table 1: analog extension module XD-4DA-V-ED general specifications
Item Specifications
Using environment No corrosive gas
Environment temperature 0℃~60℃
Storage temperature -20~70℃
Environment humidity 5~95%RH
Storage humidity 5~95%RH
Installation Fix with M3 screw or install on the rail DIN46277(width
35mm)
Dimension 100.0mm× 18.0mm× 90.0mm
Table 2: analog extension module XD-4DA-V-ED I/O precision
的导轨上
Item Analog voltage output (V)
0~10, 0~5V
Analog output range
External load resistor is 2KΩ~1MΩ
Digital input range 10-bit binary number (0~1023)
Resolution 1/1023(10Bit)
integrated precision 1%
Transformation speed 2ms/1 channel
Power supply for analog DC24V± 10%, 150mA
Table 3: analog extension module XD-4DA-V-ED AD transformation diagram
The relationship between analog output and digital input
0~10V analog output 0~5V analog output
Note: when the input data is over K1023, DA transformed analog output will keep the max
voltage.
Product appearance
Here listed I/O terminal configurations of XD series extension module XD-4DA-V-ED.
 Product structure
Each part name:
Name Function
PWR The LED lights when the ED module has power supply
Indicator COM The LED lights when the ED module communication
light port works well
ERR The LED lights when the ED module has error
24V ED module external power supply 24V +
0V ED module external power supply 24V -
VO0 Channel 1 analog output
Wiring VO1 Channel 2 analog output
terminal CO0 VO0, VO1 ground
VO2 Channel 3 analog output
VO3 Channel 4 analog output
CO1 VO2, VO3 ground
Product dimension and installation
 Installation
Do not install the module in below environment:
 Direct sunlight
 Environment temperature out of range 0-50℃
 Environment humidity out of range 35%-85% RH
 Condensation as severe changes in temperature
 Corrosive gas and flammable gas
 Dust, iron filing, salt, fume
 Vibration and impact
 Spray oil, water and medicine
 Strong magnetic field and strong electric field
XD series extension ED module can be installed in com3 port of XD series PLC.
Note: please cut off the power before operation!
COM3

Product dimension
(Unit: mm)
XD series extension ED module dimension is shown as below:
PWR
COM
ERR
Electric design reference

I/O address
XD series extension ED module will not occupy I/O unit, the transformed value is stored in
PLC register. The following is the PLC register corresponding to each channel.
Channel DA signal
0CH QD30000
1CH QD30001
2CH QD30002
3CH QD30003
 Working mode setting
Steps:
1. open the XDPpro software, find the left project bar, click PLC config/ED.
2. choose the correct module type.
3. set the module parameters such as voltage output range.
4. click write to PLC, then re-power on the PLC to make the setting effective.