Page 1 ® R&S SMBVB-K60/-K117/-K178 ® Bluetooth Signal Generation User Manual (;ÜßD2) 1178812002 Version 09...
Page 2 This document describes the following software options: ● ® R&S ® SMBVB-K60 Bluetooth EDR (1423.7853.xx) ● ® ® R&S SMBVB-K117 Bluetooth 5.x (1424.8089.xx) ● ® ® R&S SMBVB-K178 Bluetooth 6.0 (1423.9310.xx) This manual describes firmware version FW 5.30.305.xx and later of the R&S ®...
Page 3: Table Of Contents
® Contents R&S SMBVB-K60/-K117/-K178 Contents ® 1 Welcome to the Bluetooth options............. 7 Key features........................7 Accessing the Bluetooth dialog.................. 9 What's new........................9 Documentation overview....................10 1.4.1 Getting started manual....................10 1.4.2 User manuals and help....................10 1.4.3 Service manual......................10 1.4.4 Instrument security procedures..................11 1.4.5 Printed safety instructions.....................
Page 4 ® Contents R&S SMBVB-K60/-K117/-K178 2.4.4 Bluetooth modulation schemes..................33 3 Bluetooth general settings..............34 4 Dirty transmitter test settings............. 38 5 Bluetooth LE configuration and settings...........43 Channel settings......................43 Advertising event and frame configuration..............50 5.2.1 Advertising event and frame settings................50 5.2.2 Connection settings.......................53 5.2.3...
Page 5 ® Contents R&S SMBVB-K60/-K117/-K178 5.5.6 CS terminate payload settings..................128 5.5.7 CS FAE payload settings.................... 128 5.5.8 CS channel map payload settings................129 Test packet configuration..................129 6 Bluetooth BR/EDR configuration and settings....... 133 Channel settings....................... 133 Packet configuration....................135 7 Signal control and signal characteristics........143 Filter/clipping settings....................143 7.1.1 Common filter settings....................
Page 6 ® Contents R&S SMBVB-K60/-K117/-K178 8.5.7 CS channel selection commands................210 Packet configuration commands - LE..............212 8.6.1 General commands.....................218 8.6.2 Header configuration....................220 8.6.3 Payload configuration....................223 8.6.4 CS payload configuration.................... 252 Test packet configuration commands - LE............. 270 Channel configuration commands - BR/EDR............273 Packet configuration commands - BR/EDR............274 8.10 Filter/clipping commands..................283...
Page 7: Welcome To The Bluetooth ® Options
® ® R&S SMBVB-K60/-K117/-K178 Welcome to the Bluetooth options Key features ® 1 Welcome to the Bluetooth options ® The Bluetooth options R&S SMBVB-K60/-K117/-K178 are firmware applications that add functionality to generate signals in accordance with the Bluetooth standard. This user manual contains a description of the functionality that the application pro- vides, including remote control operation.
Page 8 ® ® R&S SMBVB-K60/-K117/-K178 Welcome to the Bluetooth options Key features ● Dirty transmitter test, compliant to the RF test specification with options to change start phase, frequency drift rate and frequency drift deviation ● Support of CRC corruption for every 2nd packet ●...
Page 9: Accessing The Bluetooth Dialog
® ® R&S SMBVB-K60/-K117/-K178 Welcome to the Bluetooth options What's new 1.2 Accessing the Bluetooth dialog To open the dialog with Bluetooth settings ► In the block diagram of the R&S SMBV100B, select "Baseband" > "Bluetooth". A dialog box opens that displays the provided general settings. The signal generation is not started immediately.
Page 10: Documentation Overview
® ® R&S SMBVB-K60/-K117/-K178 Welcome to the Bluetooth options Documentation overview ● Bluetooth LE channel commands added to query the channel center frequency, the channel index and the channel type, see Chapter 8.4.2, "Channel table com- mands", on page 188. ●...
Page 11: Instrument Security Procedures
® ® R&S SMBVB-K60/-K117/-K178 Welcome to the Bluetooth options Documentation overview The service manual is available for registered users on the global Rohde & Schwarz information system (GLORIS): https://gloris.rohde-schwarz.com 1.4.4 Instrument security procedures Deals with security issues when working with the R&S SMBV100B in secure areas. It is available for download on the internet.
Page 12: Videos
® ® R&S SMBVB-K60/-K117/-K178 Welcome to the Bluetooth options Notes on screenshots For some application sheets, see also: www.rohde-schwarz.com/application/smbv100b 1.4.10 Videos Find various videos on Rohde & Schwarz products and test and measurement topics on YouTube: https://www.youtube.com/@RohdeundSchwarz On the menu bar, search for your product to find related videos. Figure 1-1: Product search on YouTube 1.5 Scope Tasks (in manual or remote operation) that are also performed in the base unit in the...
Page 13: About The Bluetooth ® Options
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE ® 2 About the Bluetooth options The R&S SMBV100B provides you with the ability to generate signals in accordance with the core specification 6.0 for Bluetooth wireless technology. This section lists required options and provides background information on basic terms and principles used in Bluetooth wireless technology.
Page 14: Packet Formats For Le
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE Table 2-2: Channel index RF channel RF center frequency Data channel index Advertising channel index 2402 MHz 1 to 11 2404 MHz to 2424 MHz 0 to 10 2426 MHz 13 to 38 2428 MHz to 2478 MHz 11 to 36...
Page 15 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE Table 2-3: LE uncoded PHYs and field lengths Preamble Access address LE 1M 1 octet 4 octets 2 octets to 257 octets 3 octets 16 µs to 160 µs LE 2M 2 octets 4 octets...
Page 16: Packet Types For Le
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE 2.2.2 Packet types for LE Test packet types The test packet PDU consists of a PDU header and the payload field. The PDU header indicates the payload content type and the payload length expresses in octets. RFU means reserved for future use.
Page 17: Advertising Channel Packet Structure
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE Besides the data packet type, the instrument supports the following CONTROL_DATA packet types. Table 2-7: Control data packets for R&S SMBVB-K60 Opcode CONTROL_DATA Opcode CONTROL_DATA 0x00 LL_CONNECTION_UPDATE_IND 0x07 LL_UNKNOWN_RSP 0x01 LL_CHANNEL_MAP_IND 0x08...
Page 18 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE Table 2-9: PDU types and PHYs PDU type PDU name Physical channel LE 1M LE 2M LE Coded 0000 ADV_IND Primary advertising 0001 ADV_DIRECT_IND Primary advertising 0010 ADV_NONCONN_IND Primary advertising 0011 SCAN_REQ Primary advertising...
Page 19 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE PDU type PDU name Option Initiating PDUs CONNECT_IND R&S SMBVB- Initiating PDUs AUX_CONNECT_REQ, AUX_CONNECT_RSP R&S SMBVB- K117 Table 2-11: Advertising channel PDU fields and subfields PDU name Field and parameter Option ADV_IND, ADV_NON- AdvA, AdvData...
Page 20: Data Channel Packet Structure
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE 2.2.4 Data channel packet structure Header Header Payload 2 octets 0-251 octets 4 octets LLID NESN Length 2 bits 1 bit 1 bit 1 bit 3 bits 8 bits The 16-bit header field consists of five fields: ●...
Page 21: Direction Finding
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE Option R&S SMBVB-K60 supports LE uncoded 1 Msymbol/s (LE 1M) physical layer (PHY). Option R&S SMBVB-K117 supports LE Coded 1 Msymbol/s PHY and an optional mod- ulation scheme LE uncoded 2 Msymbol/s (LE 2M) PHY. 2.2.6 Direction finding Since Bluetooth version 5.1, a Bluetooth LE device can transmit its direction informa- tion to a Bluetooth receiver.
Page 22 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE Figure 2-4: Angle of Arrival method Angle of Departure (AoD) method A Bluetooth LE transmitter sends direction finding enabled packets using an antenna array. A receiving Bluetooth LE device, consisting of a single antenna, captures I/Q samples and the geometry of the antenna array from profile-level information.
Page 23 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE Figure 2-5: Angle of Departure method The geometry of the antenna array is information that is shared between Bluetooth LE transmitter and receiver on a profile-level. The antenna switching pattern and the method of angle estimation is specified by Constant Tone Extension.
Page 24 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE CTEInfo field Length Value Description CTETime 5 bit 2 to 20 CTE length = 8 µs * Value Other values are reserved for future use. 1 bit 1 to 2 Reserved for future use CTEType 2 bit...
Page 25: About Bluetooth Le Channel Sounding
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth LE Channel Sounding Figure 2-8: CTE structure for AoD method For more information, refer to section 2.5 Constant Tone Extension and IQ Sampling of core specification for Bluetooth wireless technology, volume 6, part B. 2.3 About Bluetooth LE Channel Sounding This section provides basic information on Bluetooth LE Channel Sounding technology.
Page 26: About Bluetooth Br/Edr
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth BR/EDR A CS procedure exists only for a limited duration, and consists of CS events, CS sube- vents, and CS steps. CS events can contain one or more subevents. CS subevents contain two or more CS steps.
Page 27: Bluetooth Packet Types For Br/Edr
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth BR/EDR Two modulation formats are used for Bluetooth: the mandatory basic rate (BR) and the optional enhanced data rate (EDR). The BR mode uses binary FM modulation and pro- vides a data rate of 1 Mbit/s. The EDR mode uses two types of PSK modulation, the π/4-DQPSK or 8DPSK, and achieves data rates of 2 Mbit/s and 3 Mbit/s, respectively.
Page 28 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth BR/EDR Table 2-16: ACL packets - enhanced rate Type Payload User Payload Slot number Header (bytes) (bytes) 2-DH1 0-54 2-DH3 0-367 2-DH5 0-679 Yes, 16-bit 3-DH1 0-83 3-DH3 0-552 2-DH5 0-1021 Figure 2-10: Packet structure of ACL packets - enhanced data rate 2.4.1.2...
Page 29 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth BR/EDR Table 2-18: eSCO packets - basic rate Type Payload User Payload Slot number Header (bytes) (bytes) 1-30 n.a. Yes, 16-bit 1-120 1-180 (Data only) Figure 2-13: Packet structure eSCO packets - basic rate Table 2-19: eSCO packets - basic rate Type Payload...
Page 30: Bluetooth Transport Modes
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth BR/EDR Table 2-21: Common link control packets: packet structure Packet Type ID Packet Types NULL and PULL Packet Types FHS 2.4.2 Bluetooth transport modes There are three different transport modes defined in the Bluetooth core specification, each of them with special applications: ●...
Page 31 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth BR/EDR Table 2-22: The access code fields Field Description Packets Preamble A fixed zero-one pattern of 4 symbols, used to facili- All packets tate DC compensation Sync word A 64-bit code word derived from a 24-bit address, All packets improves timing acquisition Trailer...
Page 32 ® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth BR/EDR Synchronous data fields Asynchronous data fields Synchronous and asynchronous data fields The meaning of some payload fields is given in the table below. Table 2-24: The payload fields Field Description Cyclic redundancy error check Guard...
Page 33: Bluetooth Modulation Schemes
® ® R&S SMBVB-K60/-K117/-K178 About the Bluetooth options About Bluetooth BR/EDR Table 2-25: The payload fields for the FHS packet Field Description Parity bits Form the first part of the sync word of the access code of the device that sends the FHS packet.
Page 34: Bluetooth General Settings
® Bluetooth general settings R&S SMBVB-K60/-K117/-K178 3 Bluetooth general settings Access: ► Select "Baseband" > "Bluetooth". The tab provides general settings to call default settings and the "Save"/"Recall" settings. Also, it provides Bluetooth version information, Bluetooth mode settings and access to further settings. Settings: State..........................34 Set To...
Page 35: Save/Recall
® Bluetooth general settings R&S SMBVB-K60/-K117/-K178 Parameter Value State Not affected by "Set To default" Bluetooth version R&S SMBVB-K60: 4.2 R&S SMBVB-K117: 5.4 R&S SMBVB-K178: 5.4 + Channel Sounding Bluetooth mode Basic Rate + EDR Transport mode ACL(Asynchronous)+EDR Packet type Sequence length 1 Frame Slot timing...
Page 36: Bluetooth Version
® Bluetooth general settings R&S SMBVB-K60/-K117/-K178 Remote command: on page 166 [:SOURce<hw>]:BB:BTOoth:WAVeform:CREate Bluetooth Version Displays the version of the standard that the firmware supports. The displayed version for Bluetooth wireless technology depends on installed options. For example, "Bluetooth Version" > "5.4" requires R&S SMBVB-K117. Remote command: on page 165 [:SOURce<hw>]:BB:BTOoth:VERSion?
Page 37: Power Ramping
® Bluetooth general settings R&S SMBVB-K60/-K117/-K178 The button also displays configured filters and the clipping state. Chapter 7.1, "Filter/clipping settings", on page 143. Remote command: on page 285 [:SOURce<hw>]:BB:BTOoth:FILTer:FILTers? on page 284 [:SOURce<hw>]:BB:BTOoth:CLIPping:STATe Power Ramping Opens a dialog to configure the power ramping. Chapter 7.2, "Power ramping settings", on page 149.
Page 38: Dirty Transmitter Test Settings
® Dirty transmitter test settings R&S SMBVB-K60/-K117/-K178 4 Dirty transmitter test settings Access: 1. Select "Bluetooth" > "General". 2. Select "Dirty Transmitter Test". The dialog provides settings to configure dirty transmitter test settings. These set- tings contain parameters that you can change for the central device signal. It is used to test the connection under 'dirty transmitter' conditions, and to define the influence on the receiver quality (bit error rate tests).
Page 39: Settings: Set To Default
® Dirty transmitter test settings R&S SMBVB-K60/-K117/-K178 Table 4-2: Dirty transmitter test parameters for EDR Δt /ppm offset error Table 4-3: Dirty transmitter test parameters for LE Δt /ppm offset error standard stable 0.45 0.495 0.48 0.498 0.46 0.496 0.52 0.502 0.53 0.503...
Page 40: Dirty Transmitter Test
® Dirty transmitter test settings R&S SMBVB-K60/-K117/-K178 Dirty Transmitter Test Enables the dirty transmitter test. The setting is available for the following packet types: ● BR: DH1, DH3, DH5 For basic rate packets, each enabled set of parameters in the "Dirty Transmitter Setting"...
Page 41: Number Of Packets Per Set/Number Of Steps Per Set
® Dirty transmitter test settings R&S SMBVB-K60/-K117/-K178 A sine wave is used to drift the modulated Bluetooth signal around center frequency + carrier frequency offset. The maximum deviation reached during the drift equals the set frequency drift deviation. Remote command: on page 167 [:SOURce<hw>]:BB:BTOoth:DTTest:FDDeviation Number Of Packets Per Set/Number Of Steps Per Set...
Page 42: Symbol Timing Error (Ppm)
® Dirty transmitter test settings R&S SMBVB-K60/-K117/-K178 Remote command: [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:CFOFfset on page 169 [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:SHORt:SET<ch>:CFOFfset on page 171 Symbol Timing Error (ppm) ← Dirty Transmitter Setting Sets the symbol timing error in ppm. The symbol timing error modifies the symbol clock frequency by the specified value. Remote command: [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:STERror on page 171...
Page 43: Bluetooth Le Configuration And Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings 5 Bluetooth LE configuration and settings Access: 1. Select "Baseband" > "Bluetooth". 2. Select "Bluetooth Mode" > "Bluetooth Low Energy". The remote commands required to define these settings are described in Chapter 8, "Remote control commands",...
Page 44 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings The tab provides settings to configure channel settings and general packet set- tings. To display Bluetooth LE event or frame sequences Depending on the channel type packet type and packet format, the "Channel" tab dis- plays a chart at the bottom that illustrates sequences of the corresponding events or frames.
Page 45: Settings: Channel Type
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings Settings: Channel Type........................ 45 Packet Type........................45 Packet Format.......................47 Duty Cycle........................47 Sequence Length......................47 Bluetooth Controller Role....................47 Bluetooth Controller State..................... 48 Corrupted CRC Every 2nd Packet................48 Payload Type........................ 48 Duration.........................48 Modulation Format......................
Page 46 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings Channel type Packet/PDU type Option Advertising TEST PACKET R&S SMBVB-K60 Advertising CONTINUOUS R&S SMBVB-K60 Data DATA R&S SMBVB-K60 Data CONTROL_DATA, see Table 5-2. Table 5-2. Data TEST PACKET R&S SMBVB-K60 Data CONTINUOUS R&S SMBVB-K60...
Page 47: Packet Format
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings How to: "To display Bluetooth LE event or frame sequences" on page 44 For more information, refer to the specifications document. Remote command: on page 176 [:SOURce<hw>]:BB:BTOoth:UPTYpe Packet Format Selects the packet format that is the format according to the physical layer (PHY) that supports the packet type or PDU type.
Page 48: Bluetooth Controller State
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings Bluetooth controller Channel type PDU type role Advertiser (read-only) Advertising ADV_IND, ADV_DIRECT_IND, ADV_NON- CONN_IND, ADV_SCAN_IND, SCAN_RSP, ADV_EXT_IND, AUX_ADV_IND, AUX_CHAIN_IND, AUX_SYNC_IND, AUX_SCAN_RSP, AUX_CON- NECT_RSP, TEST PACKET Scanner (read-only) Advertising SCAN_REQ, AUX_SCAN_REQ Initiator (read-only) Advertising CONNECT_IND, AUX_CONNECT_IND...
Page 49: Event Configuration/Frame Configuration
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings Specifies the physical layer. Remote command: on page 178 [:SOURce<hw>]:BB:BTOoth:MFORmat Event Configuration/Frame Configuration Opens the "Event Configuration" dialog, if the sequence length of the packet type is expressed in events or opens the "Frame Configuration" dialog, if it is expressed in frames, see Chapter 5.2, "Advertising event and frame configuration",...
Page 50: Advertising Event And Frame Configuration
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising event and frame configuration Role Requires R&S SMBVB-K178 and "Channel Type" > "Channel Sounding". Sets the role of the Channel Sounding device. "Initiator" Channel Sounding device initiates a CS procedure. "Reflector" Channel Sounding device responds to a CS procedure.
Page 51 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising event and frame configuration 2. Select "Event Configuration" for event-type packets or "Frame Configuration" for frame-type packets. Figure 5-1: Event configuration for an advertising channel (advertiser) Figure 5-2: Frame configuration for an advertising channel (scanner) The "Advertising Settings"...
Page 52 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising event and frame configuration Sets the time interval between two consecutive advertising events, regarding the start- ing points. Remote command: For packet type ADV_DIRECT_IND and duty cycle high: on page 181 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:ADINterval For all others: on page 181...
Page 53: Connection Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising event and frame configuration Transmit Window Offset Requires packet type CONNECT_IND, AUX_CONNECT_REQ or AUX_CON- NECT_RSP. Displays the start point of the transmit window. For related settings, see "Transmit Win- dow Offset" on page 77.
Page 54 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising event and frame configuration Settings: No. Of Tx Packets/Event....................54 Connection Event Interval..................... 54 LL Connection Mode..................... 54 Long Term Key(hex)......................55 Selected Data Channel Index..................55 No. Of Tx Packets/Event Sets the number of TX packets per event. Each connection contains at least one data channel packet.
Page 55: Channel Table
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising event and frame configuration "Un-encrypted" Payload data is transmitted without encoding. Example of packet type data: "Encrypted" The link layer connection runs in encrypted mode. Example of packet type data: Remote command: on page 182 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:LCMode Long Term Key(hex)
Page 56 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising event and frame configuration 2. Select "Channel Table" The channel table displays all possible channels and their characteristics. Also you can select the channel that you want to use for the generated packets. Each row lists the configuration for a channel as per the data channel index.
Page 57: Advertising And Data Packet Configuration
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Channel Type Displays the channel type that is data or advertising. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:ACTable:CHANnel<ch0>: on page 189 CTYPe? [:SOURce<hw>]:BB:BTOoth:ECONfiguration:DCTable:CHANnel<ch0>: on page 189 CTYPe? Channel State Sets if you use the channel ("Used") or not ("Unused"). You can only use one channel. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:ACTable:CHANnel<ch0>: on page 190...
Page 58: Packet Configuration Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration ● Initiating PDU payload settings................75 ● Data channel PDU payload settings............... 79 ● FeatureSet configuration settings................89 5.3.1 Packet configuration settings Access: ► Select "Packet Configuration". The "Packet Configuration"...
Page 59: Header Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Bluetooth LE transmissions are based on an interface packet format that consists of a preamble (8 bits) the access address (32 bits), the PDU and CRC (24 bits). Access address is used to identify communications on a physical channel, and to exclude or ignore packets on different physical channels.
Page 60 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Settings: NESN Start Value......................60 SN Start Value.......................60 Channel Selection......................60 CTEInfo Present......................60 CTEInfo Configuration....................61 Tx Address Type/Rx Address Type................61 NESN Start Value Requires a data channel packet that is not a test packet. Sets the next expected sequence number (NESN).
Page 61: Cteinfo Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration CTEInfo Configuration Requires "CTEInfo Present" > "On". Opens the "CTEInfo Configuration" dialog to configure CTE length and the CTE method. See Chapter 5.3.3, "CTEInfo settings", on page 61. Tx Address Type/Rx Address Type Requires an advertising channel packet, see Table...
Page 62 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration 4. Select "CTEInfo Configuration". The dialog provides constant tone extension (CTE) settings for direction finding including the CTE length and the CTE method. The settings are relevant for data event configuration and all data channel packet types including test packets.
Page 63: Legacy Advertising Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Sets the gain of the antenna "AntennaX", where X is 0 to 3 depending on the number of antennas. You can set the antenna gain information of up for four individual anten- nas for direction finding.
Page 64 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration – MSB: 24 bits = company_id ● "Random Address Type" is an optional 48-bit random static device address. ● "Private Address Type" is a resolvable 48-bit optional address. A private address consists of the: –...
Page 65: Extended Advertising Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration An internally generated pseudo-random noise sequence. ● "Pattern" An internally generated sequence according to a bit pattern. Use the "Pattern" box to set the bit pattern. ● "Data List"/"Select Data List"...
Page 66: General Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration For an overview of supported extended advertising PDUs, see Table 2-10. ● General settings...................... 66 ● Extended header settings..................67 ● AdvDataInfo configuration settings................. 70 ● AuxPtr configuration settings..................
Page 67: Extended Header Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AMODe on page 228 Extended Header Enables the extended header of an extended advertising PDU. If enabled, displays a table with extended header settings, see Chapter 5.3.5.2, "Exten- ded header settings",...
Page 68 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration AdvA Enables the flag of the advertiser's device address (AdvA) subfield. If enabled, this subfield is present in the Extened Header field. For related settings, see "Advertiser's Device Addr" on page 63.
Page 69 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:EHFLags: on page 235 APTR:STATe SyncInfo/SyncInfo Configuration Requires packet type AUX_ADV_IND or LL_PERIODIC_SYNC_IND. Enables the flag of the SyncInfo subfield. If enabled, this subfield is present in the Ext- ened Header field.
Page 70: Advdatainfo Configuration Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration See also: ● Section "About data signals" in the R&S SMBV100B user manual. ● Section "File and data management" in the R&S SMBV100B user manual. ● Section "Data list editor" in the R&S SMBV100B user manual. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD on page 225...
Page 71: Auxptr Configuration Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Advertising Set ID(hex) Sets the "Advertising Set ID" in the AdvDataInfo field. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ASID on page 230 5.3.5.4 AuxPtr configuration settings Access: 1. Select "Payload" > "Extended Header". 2.
Page 72: Syncinfo Configuration Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AOUNits on page 229 AUX Offset Sets the time from the start of the packet containing the AuxPtr field to the approximate start of the auxiliary packet. The parameter "Offset Units"...
Page 73 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Sync Packet Offset......................73 Offset Units........................73 Offset Adjust........................73 Periodic Adv Interval..................... 73 Sleep Clock Accuracy....................73 Access Address......................73 CRC Initial Value(hex)....................73 Event Counter....................... 73 Sync Packet Offset Specifies the time from the start of the AUX_ADV_IND packet containing the SyncInfo field to the start of the AUX_SYNC_IND packet.
Page 74: Scanning Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ECOunter on page 234 5.3.6 Scanning PDU payload settings Access: 1. Select a scanning PDU: a) In the "Channel" tab, select "Channel Type" > "Advertising". b) Select a scanning PDU, for example "Packet Type"...
Page 75: Initiating Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SNUap on page 228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SLAP on page 227 Advertiser's Device Addr "Advertiser's Device Addr" on page 63. Data Source Requires a SCAN_RSP PDU or an AUX_SCAN_RSP PDU. For related settings, see "Data Source"...
Page 76 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration The tab provides settings to configure the payload of the initiating PDUs. For an overview of supported initiating PDUs, see Table 2-10. Settings: Initiator's Device Addr....................76 Advertiser's Device Addr....................
Page 77 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: For advertising channels: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:WSIZe on page 249 For data channels: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NWSize on page 242 Transmit Window Offset Requires packet type CONNECT_IND, AUX_CONNECT_REQ, LL_CONNEC- TION_UPDATE_IND, LL_CONNECTION_PARAM_REQ or LL_CONNEC- TION_PARAM_RSP.
Page 78 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SLATency on page 246 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NSLatency on page 242 LL Connection Timeout Requires packet type CONNECT_IND, AUX_CONNECT_REQ, LL_CONNEC- TION_UPDATE_IND, LL_CONNECTION_PARAM_REQ or LL_CONNEC- TION_PARAM_REQ. The PDUs AUX_CONNECT_REQ, LL_CONNEC- TION_PARAM_REQ and LL_CONNECTION_PARAM_REQ also require option R&S SMBVB-K117.
Page 79: Data Channel Pdu Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Data Source Requires an AUX_CONNECT_RSP PDU. For related settings, see "Data Source" on page 64. Data Length Requires an AUX_CONNECT_RSP PDU. For related settings, see "Data Length" on page 65.
Page 80 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Encrypted DIVersifier(hex).................... 82 Session Key iD(hex)......................82 Initialization Vector(hex)....................82 Unknown Type(hex)...................... 82 FeatureSet Length......................83 FeatureSet Configuration....................83 Version Number(hex)....................83 SubVersion Number(hex)....................83 Company Id(hex)......................83 Min. Interval........................83 Max.
Page 81 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Connection Event Interval Requires packet type LL_CONNECTION_UPDATE_IND, LL_CONNEC- TION_PARAM_REQ or LL_CONNECTION_PARAM_RSP. The PDUs LL_CONNEC- TION_PARAM_REQ and LL_CONNECTION_PARAM_RSP also require option R&S SMBVB-K117. For related settings, see "Connection Event Interval" on page 77.
Page 82 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ECODe on page 233 Random Vector(hex) Requires the packet type LL_ENC_REQ and a Central Bluetooth controller. Sets the random vector of the Central device for device identification. The parameter is an initialization vector provided by the host in the HCI_ULP_Start_Encryption command.
Page 83 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:UTYPe on page 248 FeatureSet Length Requires the packet type LL_FEATURE_REQ, LL_FEATURE_RSP or LL_PERIPH- ERAL_FEATURE_REQ. Displays the length of the feature set. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:FSLength on page 237 FeatureSet Configuration Requires the packet type LL_FEATURE_REQ, LL_FEATURE_RSP or LL_PERIPH-...
Page 84 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MNINterval on page 183 Max. Interval Requires option R&S SMBVB-K117 and packet types LL_CONNEC- TION_PARAM_REQ or LL_CONNECTION_PARAM_RSP. Sets the maximum allowed connection interval. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MXINterval on page 184 Preferred Periodicity...
Page 85 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration "State" Enables the offset point state. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration: on page 184 PCONfiguration:OFFSet<ch0>:STATe "Offset(ms)" Sets the offset value. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration: on page 184 PCONfiguration:OFFSet<ch0>:VALue Reject Opcode Requires option R&S SMBVB-K117 and packet type LL_REJECT_EXT_IND.
Page 86 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:RPHYs: on page 244 LCOD:STATe [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L1M: on page 244 STATe [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L2M: on page 245 STATe [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs: on page 245 LCOD:STATe M_TO_S_PHY/S_TO_M_PHY Requires option R&S SMBVB-K117 and packet type LL_PHY_UPDATE_IND. Sets the physical layers of the Central-to-Peripheral (C_TO_P) direction and Periph- eral-to-Central (P_TO_C) direction.
Page 87 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MUCHannels on page 240 ID(hex) Requires option R&S SMBVB-K117 and packet type LL_PERIODIC_SYNC_IND. Sets the ID of the identifier specified by the Host in the CtrData field. The value is in hexadecimal representation.
Page 88 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration The SID is typically equal to the Advertising SID subfield of the advertising set pointing to periodic advertising. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SID on page 252 Address Type Requires option R&S SMBVB-K117 and packet type LL_PERIODIC_SYNC_IND. Sets the address type in the CtrData field.
Page 89: Featureset Configuration Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Advertising and data packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MCLReq on page 250 CTETypeReq Requires option R&S SMBVB-K117 and packet type LL_CTE_REQ. Sets the 2-bit constant tone extension type in the CtrData field. Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTReq on page 221 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MCLReq...
Page 90: Cs Subevent Configuration
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration Settings: FeatureSet configuration table Displays available features within the link layer control PDU. For configurable features, see the table Table 5-5. To enable the feature, select "Valid" > "On" to the right of the feature. Table 5-5: Link layer features: Bit number and feature Link layer feature Link layer feature...
Page 91: Subevent Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration 5. Select "CS Subevent Configuration". The dialog provides settings to configure Channel Sounding (CS) subevents. For more information, refer to the Bluetooth Core Specification [1]. Settings: ● Subevent settings....................91 ●...
Page 92: Subevent Length
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration b) Select "Connector" > "User 3" > "Direction" > "Input". c) Select "Connector" > "User 3" > "Signal" > "Global Trigger". 5. Configure the external trigger signal characteristics, for example as follows: a) Select "Global Connectors"...
Page 93: Step Scheduling
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration For "Number of Subevents" = "1", the subevent interval is 0μs. For "Number of Sube- vents" higher than "1", settable subevent intervals depend on the number of event intervals, the connection interval, the event offset and the subevent length. Remote command: on page 194 [:SOURce<hw>]:BB:BTOoth:CS:SINTerval...
Page 94: Subevent
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration The table allows you to check or configure the following parameters for each subevent individually: ● "Subevent" on page 94 ● "Number of Steps" on page 94 ● "Subevent Space (µs)" on page 94 ●...
Page 95: Channel Table
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration Remote command: on page 196 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MZSTeps CS Step Config Opens a dialog to configure CS steps, see Chapter 5.4.5, "CS step configuration", on page 100. CS Step Info Opens a dialog that provides information on configured CS steps per subevent in a table, see Chapter 5.4.6, "CS step info",...
Page 96: Cs Security Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration For example, for "Channel 0" the channel index is 0 and the center frequency is 2402 MHz. See also Table 2-13. Remote command: Via suffix CHANnel<ch> Center Frequency (MHz) Displays the center frequency of the channel.
Page 97 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration 2. Select "CS Security". The tab provides settings to configure CS security settings. Settings: CS_IV_C(hex)....................... 97 CS_IV_P(hex)....................... 97 CS_IN_C(hex).......................97 CS_IN_P(hex)....................... 97 CS_PV_C(hex)......................98 CS_PV_P(hex)......................98 CS_IV_C(hex) Requires packet type CS SEQUENCE or LL_CS_SEC_REQ. Sets the CS_IV_C parameter.
Page 98: Channel Selection Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration CS_PV_C(hex) Requires packet type CS SEQUENCE or LL_CS_SEC_REQ. Sets the CS_PV_C parameter. The parameter is 64-bit in hexadecimal representation. Remote command: on page 210 [:SOURce<hw>]:BB:BTOoth:CS:CSPVc CS_PV_P(hex) Requires packet type CS SEQUENCE or LL_CS_SEC_RSP. Sets the CS_PV_P parameter.
Page 99 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration The value equals the number of cycles of the ChM field for non-Mode-0 CS steps within a CS procedure. Remote command: on page 211 [:SOURce<hw>]:BB:BTOoth:CS:CMRepetition ChSel Sets the algorithm to select the channels. "Algorithm #3b"...
Page 100: Cs Step Configuration
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration 5.4.5 CS step configuration Access: 1. Select "CS Subevent Configuration". 2. Select "Subevent Settings" > "Subevent 0" > "CS Step Config...". The "CS Step Config" tab of the "Structure for Subevent x" dialog opens. The tab provides CS step settings for the first subevent "Subevent 0".
Page 101 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration Main_Mode Sets the main mode of the CS step. "Mode-1" Mode-1 mode with no submode available. "Mode-2" Mode-2 mode with submodes "Mode-1" and "Mode-3" available. "Mode-3" Mode-3 mode with submode "Mode-2" available. The table Table 5-8 provides an overview on available submodes per main mode.
Page 102 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration Remote command: on page 199 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SMSTep? 5.4.5.2 Mode-0 config settings Access: ► Select "CS Step Config" > "Mode-0 Config". The tab provides Mode-0 CS step settings. Settings: T_IP1 Sets the time "T_IP1" for Mode-0 CS steps. Remote command: on page 199 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MZERo:TIPO...
Page 103 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration ● Select "Main_Mode" > "Mode-2" and "Sub_Mode" > "Mode-1". The tab provides Mode-1 CS step settings. Settings: T_IP1...........................103 Sequence Length......................103 Sequence Type......................104 User Payload Pattern....................104 Select Data List......................
Page 104 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration Sequence Type Sets the sequence type. "Sounding Sequence" Sounding sequence "Random Sequence" Random sequence Remote command: on page 201 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:STYPe User Payload Pattern Displaying the parameter "User Payload Pattern" requires the following: ●...
Page 105 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration ● Select "Main_Mode" > "Mode-3" and "Sub_Mode" > "Mode-2". The tab provides Mode-2 CS step settings. Settings: T_SW.......................... 105 N_AP...........................105 T_PM...........................105 T_IP2...........................105 T_SW Sets the time "T_SW" for Mode-2. Remote command: on page 200 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTWO:TSW?
Page 106 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration 5.4.5.5 Mode-3 config settings Access: 1. Select "CS Step Config" > "General". 2. Select Mode-3 in the CS step main mode or submode: ● Select "Main_Mode" > "Mode-3". ● Select "Main_Mode"...
Page 107 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration T_PM Sets the time "T_PM" for Mode-3. Remote command: on page 200 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTHRee:TPM T_IP2 Sets the time "T_IP2" for Mode-3. Remote command: on page 201 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTHRee:TIPT Sequence Length Sets the sequence length. The length is discrete and depends on the sequence type. The table below lists available sequence length values for sounding sequences and random sequences.
Page 108: Cs Step Info
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration "PRBS 9 sequence"/"PRBS 15 sequence" Pseudo random bit sequences of the length 9 or 15 - transmission of identical packet series. Predefined pattern "Repeated 11110000 sequence", "Repeated 10101010 sequence", "Repeated 11111111 sequence", "Repeated 00000000 sequence", "Repeated 00001111 sequence"...
Page 109: Settings: Step
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration The tab provides the step table that lists the properties and settings for individual CS steps per subevent. The number of rows equals the number of CS steps per subevent.
Page 110: Channel Index
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration Example: This example assumes manual step scheduling for one subevent with three CS steps and one mode-0 step. The CS step main mode is mode-3. Set as follows: "Step Scheduling" > "Manual", "Number of Subevents" = "1", "Number of Steps" = "3", "Mode-0 Steps"...
Page 111: Companion Signal
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS subevent configuration For CS test packets, you can set the content for a sounding sequence and random sequence, see "Sequence Type" on page 104. Remote command: [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:SCONtent on page 204 Companion Signal Sets the companion signal and the data source.
Page 112: Cs Control Data Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Requires "Companion Signal" ≠ "None". "Data Source" Selects the data source. The following standard data sources are available: ● "All 0"/"All 1" An internally generated sequence containing 0 data or 1 data. ●...
Page 113: Cs Security Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Access: 1. Select "Packet Configuration". 2. Select "Payload". The tab provides settings to configure the packet/PDU payload. ● CS security payload settings................. 113 ● CS capabilities payload settings................113 ●...
Page 114 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Settings: ● CpbData 1 settings....................114 ● CpbData 2 settings....................116 ● CpbData 3 settings....................117 5.5.2.1 CpbData 1 settings Mode_Types........................114 RTT_Capability......................114 RTT_AA_Only......................114 RTT_Sounding_N......................115 RTT_Random_Sequence_N..................115 NADM_Sounding_Capability..................115 NADM_Random_Sequence_Capability..............115 CS_SYNC_PHY_Capability..................
Page 115 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings RTT_Sounding_N Displays or sets the time values of the RTT_Sounding_N field. Setting the value depends on the bits of the RTT_Capability field. See the table Table 5-9 for an overview.
Page 116 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Role "Role" on page 50. Companion_Signal Enables the companion signal. See also "Companion Signal" on page 111. Remote command: on page 258 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSIGnal 5.5.2.2 CpbData 2 settings No_FAE........................
Page 117 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Sets the bits that are reserved for future use (RFU). The number of RFU bits can vary depending on the CS_Control_Data PDU. Remote command: on page 265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RFU Num_Configs Sets the Num_Configs field that relates to the number of independent CS configura-...
Page 118 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings "T_IP1" Displays the T_IP1 time of the bit position. "T_IP1 Capability" Enables the T_IP1 capability per bit position. Remote command: [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TIPO: on page 255 CAPability Show T_IP2 Capability Table/Hide T_IP2 Capability Table Shows or hides the "T_IP2_Capability Table".
Page 119: Cs Configuration Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings T_PM_Capability Table The table provides settings to enable the T_PM capability including the T_PM time per bit position. You can enable T_PM capabilities for bit position 0 to bit position 2. "Bit Position"...
Page 120 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings ChM_Repetition Sets the 3-bit ChM_Repetition field. The value equals the number of cycles of the ChM field for non-Mode-0 CS steps within a CS procedure. Remote command: on page 211 [:SOURce<hw>]:BB:BTOoth:CS:CMRepetition Main_Mode...
Page 121 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings This value indicates the TX PHY of the remote device, to which the Pwr_Delta field in this PDU applies. See also "Packet Format" on page 47. Remote command: on page 264 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:PHY? RTT_Type...
Page 122: Cs Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Sets the bits that are reserved for future use (RFU). The number of RFU bits can vary depending on the CS_Control_Data PDU. Remote command: on page 265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RFU ChSel "ChSel"...
Page 123 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Settings: Config_ID........................123 RFU..........................123 connEventCount......................123 Offset_Min........................123 Offset_Max........................124 Max_Procedure_Len....................124 Event_Interval......................124 Subevent_Per_Event....................124 Subevent_Interval....................... 124 Subevent_Len......................125 Procedure_Interval......................125 Procedure_Count......................125 ACI..........................125 PHY..........................125 Preferred_Peer_Ant....................125 Pwr_Delta........................126 Config_ID Sets the 6-bit Config_ID field that is the CS configuration ID. Settable ID values are 2 bits in decimal representation.
Page 124 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings The Offset_Min time value is greater than or equal to 500 μs and less than 4 s. Remote command: on page 263 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:OMIN Offset_Max Sets the time value of the Offset_Max field. The value has a length of 3 octets or 9 bits. The field corresponds to the proposed maximum time between the ACL anchor point and the offset of the first CS step of the first CS subevent.
Page 125 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Subevent_Len Sets the subevent length in the Subevent_Len field. The value has a length of 3 octets or 9 bits. The Subevent_Len field implies the maximum duration of each CS subevent in micro- seconds.
Page 126: Cs Ind Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Table 5-11: Preferred_Peer_Ant field values Bit number Description <PrePeerAnt> Use the first ordered antenna element ANT0 Use the second ordered antenna element ANT1 Use the third ordered antenna element ANT2 Use the fourth ordered antenna element ANT3...
Page 127 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Remote command: on page 257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CID Sets the bits that are reserved for future use (RFU). The number of RFU bits can vary depending on the CS_Control_Data PDU. Remote command: on page 265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RFU...
Page 128: Cs Terminate Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 CS control data payload settings Remote command: on page 257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:ACI Displays the LE physical layer that is the LE uncoded PHY LE1M. See also "Packet Format" on page 47. Remote command: on page 175 [:SOURce<hw>]:BB:BTOoth:PFORmat Pwr_Delta...
Page 129: Cs Channel Map Payload Settings
® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Test packet configuration Settings: Show Channel FAE Table/Hide Channel FAE Table........... 129 Channel FAE Table..................... 129 Show Channel FAE Table/Hide Channel FAE Table Shows or hides the fractional frequency offset actuation error (FAE) channel table. "Channel FAE Table"...
Page 130 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Test packet configuration 3. Select "Channel" > "Packet Type" > "TEST PACKET". 4. Select "Test Packet Configuration". The dialog provides settings to configure test packets. The graphic below the set- tings shows the test packet structure and fields. Settings: Packet Configuration....................130...
Page 131 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Test packet configuration Remote command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPBit on page 270 Header The "Header" section provides settings to configure the header of the test packet. CTEInfo Present Requires a data channel packet or a test packet. Enables the CTEInfo field in the header of Bluetooth LE data packets in the LE unco- ded PHY.
Page 132 ® Bluetooth LE configuration and settings R&S SMBVB-K60/-K117/-K178 Test packet configuration Predefined pattern 11110000, 10101010, 11111111, 00000000, 00001111 or 01010101 "Data List" "Data Source" on page 64. Remote command: [:SOURce<hw>]:BB:BTOoth:DTTest:TPConfiguration:UPSource on page 272 Payload Length Sets the payload length of the test packet. Remote command: [:SOURce<hw>]:BB:BTOoth:DTTest:TPConfiguration:UPLength on page 272...
Page 133: Bluetooth Br/Edr Configuration And Settings
® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings 6 Bluetooth BR/EDR configuration and set- tings Access: 1. Select "Baseband" > "Bluetooth". 2. Select "Bluetooth Mode" > "Basic Rate + EDR". The remote commands required to define these settings are described in Chapter 8, "Remote control commands",...
Page 134 ® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Channel settings For Bluetooth LE channel settings, see Chapter 5.1, "Channel settings", on page 43. Settings: Packet Type........................ 134 Sequence Length......................134 Slot Timing........................134 Packet Configuration....................135 Packet Type Selects the packet type. The available packets depend on the selected Transport Mode.
Page 135: Packet Configuration
® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Packet configuration Packet Configuration Access the "Packet Configuration" dialog, see Chapter 6.2, "Packet configuration", on page 135. The current data source for the packet and the data whitening state are displayed next to the button.
Page 136 ® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Packet configuration └ Acknowledgment...................138 └ SEQN Start Value..................138 Payload........................138 └ Data Source....................138 └ Data Length....................139 └ EIR packet follows..................139 └ Flow Control....................139 └ Scan Repetition Mode...................140 └ Class of Device.....................
Page 137 ® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Packet configuration Sets the 24-bit lower address part (LAP) in the 64-bit sync word separately, if "Syn- chronize LAP with BD_ADDR > OFF". The LAP is obtained automatically from the Bluetooth device address "BD_ADDR > LAP", if "Synchronize LAP with BD_ADDR >...
Page 138 ® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Packet configuration Sets the FLOW bit in the header. This bit indicates the start or stop of transmission of packets over the ACL logical transport. "Go" Allows the other devices to transmit new data. "Stop"...
Page 139 ® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Packet configuration ● "PNxx" An internally generated pseudo-random noise sequence. ● "Pattern" An internally generated sequence according to a bit pattern. Use the "Pattern" box to set the bit pattern. ● "Data List"/"Select Data List" Binary data from a list file, internally or externally generated.
Page 140 ® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Packet configuration Remote command: on page 281 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:PFControl Scan Repetition Mode ← Payload Available for FHS packets. The 2-bit scan repetition field indicates the interval between two consecutive page scan windows, determines the behavior of the paging device. "R0"...
Page 141 ® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Packet configuration An internally generated pseudo-random noise sequence. ● "Pattern" An internally generated sequence according to a bit pattern. Use the "Pattern" box to set the bit pattern. ● "Data List"/"Select Data List" Binary data from a list file, internally or externally generated.
Page 142 ® Bluetooth BR/EDR configuration and settings R&S SMBVB-K60/-K117/-K178 Packet configuration Remote command: on page 277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA on page 277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:DPATtern on page 277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:DSELection Data Length ← DV Payload (Available for all packet types except ID, POLL, NULL and FHS packets) Enters the payload data length in bytes.
Page 143: Signal Control And Signal Characteristics
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Filter/clipping settings 7 Signal control and signal characteristics This section lists settings provided for configuring the baseband filter and configuring power ramping of bluetooth bursts. Also settings are listed for defining the signal gen- eration start and for generating signals necessary for synchronization with other instru- ments.
Page 144: Common Filter Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Filter/clipping settings Settings: 7.1.1 Common filter settings....................144 7.1.2 DPSK filter settings..................... 145 7.1.3 Modulation settings..................... 146 7.1.4 Clipping settings......................148 7.1.1 Common filter settings Access: 1. Select "General" > "Filter"/"Clipping". 2. Select "Filter" > "GFSK section". The section provides settings to configure the common baseband GFSK filter.
Page 145: Dpsk Filter Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Filter/clipping settings on page 288 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:GAUSs on page 289 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:LPASs on page 289 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:PGAuss on page 289 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:RCOSine on page 290 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:SPHase Impulse Length Displays the number of filter tabs. If enabled, the most sensible parameter values are selected. The value depends on the coherence check.
Page 146: Modulation Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Filter/clipping settings Table 7-1: DPSK filter for Bluetooth EDR packets Transport mode Packet type DPSK filter type ACL+EDR 2-DH1, 2-DH3, 2-DH5 π/4 DQPSK 3-DH1, 3-DH3, 3-DH5 8DPSK eSCO+EDR 2-EV3, 2-EV5 π/4 DQPSK 3-EV3, 3-EV5 8DPSK Settings:...
Page 147 ® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Filter/clipping settings 2. Select "Modulation Settings". The tab provides settings to configure modulation settings. Settings: Modulation Type......................147 Frequency Deviation....................147 Modulation Index......................147 Symbol Rate Variation....................148 Modulation Type Displays the modulation format used for the current packet selection. Remote command: on page 287 [:SOURce<hw>]:BB:BTOoth:FILTer:MTYPe...
Page 148: Clipping Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Filter/clipping settings Symbol Rate Variation Enter the symbol rate. Remote command: on page 290 [:SOURce<hw>]:BB:BTOoth:SRATe:VARiation 7.1.4 Clipping settings Access: 1. Select "General" > "Filter"/"Clipping". 2. Select "Clipping". The tab provides settings to configure clipping. Settings: State..........................148 Clipping...
Page 149: Power Ramping Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Power ramping settings Clipping Mode Selects the clipping method. The dialog displays a graphical illustration on how this two methods work. ● "Vector | i + jq |" The limit is related to the amplitude | i + q |. The I and Q components are mapped together, the angle is retained.
Page 150 ® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Power ramping settings Settings: Ramp Function......................150 Ramp Time........................150 Rise Offset........................150 Fall Offset........................150 Ramp Function Selects the form of the transmitted power, i.e. the shape of the rising and falling edges during power ramp control. The transmitted power rises and falls with linear fashion.
Page 151: Trigger Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Trigger settings 7.3 Trigger settings Access: ► Select "Baseband" > "Bluetooth" > "Trigger In". This tab provides settings to select and configure the trigger, like trigger source, trigger mode and trigger delays, and to arm or trigger an internal trigger manually. The header of the tab displays the status of the trigger signal and trigger mode.
Page 152 ® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Trigger settings Execute Trigger......................153 Source.........................154 Sync. Output to Ext. Trigger/Sync. Output to Trigger..........154 External Inhibit/Trigger Inhibit..................155 External Delay/Trigger Delay..................155 Mode Selects the trigger mode. The mode determines the effect of a trigger event on the sig- nal generation.
Page 153 ® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Trigger settings Running/Stopped With enabled modulation, displays the status of signal generation for all trigger modes. ● "Running" The signal is generated; a trigger was (internally or externally) initiated in triggered mode. ●...
Page 154 ® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Trigger settings Source The following sources of the trigger signal are available: ● "Internal" The trigger event is internal. Tap "Execute Trigger" to trigger signal generation manually. ● "External Global Trigger" The trigger event is the active edge of an external trigger signal provided and con- figured at the User x connectors.
Page 155 ® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Trigger settings In primary-secondary instrument mode, this setting ensures that once achieved, syn- chronization is not lost if the baseband signal sampling rate changes. Remote command: [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:SYNChronize:OUTPut on page 297 External Inhibit/Trigger Inhibit Applies for an external trigger signal.
Page 156: Marker Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Marker settings 7.4 Marker settings Access: ► Select "Baseband" > "Bluetooth" > "Marker". This tab provides settings to select and configure the marker output signal includ- ing marker mode and marker delay. Routing and activating a marker signal 1.
Page 157 ® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Marker settings "Event/Frame Start" A marker signal is generated at the start of each event/frame. The term event corresponds to a Bluetooth LE event, the term frame cor- responds to a Bluetooth BR/EDR frame. "Event/Frame Active Part"/"Event/Frame Inactive Part"...
Page 158: Clock Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Clock settings "On/Off Ratio" A regular marker signal that is defined by an on/off ratio is generated. A period lasts one On and Off cycle. If "Marker Mode > On/Off Ratio", specify the "On Time" and "Off Time", which are expressed as the number of samples.
Page 159: Global Connectors Settings
® Signal control and signal characteristics R&S SMBVB-K60/-K117/-K178 Global connectors settings 3. Activate baseband signal generation. In the block diagram, set "Baseband" > "On". The R&S SMBV100B starts baseband signal generation with a symbol rate that equals the clock rate. About clock signals This section focuses on the available settings.
Page 160: Remote Control Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 8 Remote control commands The following commands are required to perform signal generation with the Bluetooth options in a remote environment. We assume that the R&S SMBV100B has already been set up for remote operation in a network as described in the R&S SMBV100B documentation.
Page 161: General Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 General commands ● Packet configuration commands - BR/EDR............274 ● Filter/clipping commands..................283 ● Power ramping commands................... 290 ● Trigger commands....................292 ● Marker commands....................298 ● Clock commands....................302 8.1 General commands Example: To configure time units for timing and delay commands The default time unit of timing and delay commands is millisecond.
Page 162 ® Remote control commands R&S SMBVB-K60/-K117/-K178 General commands Example: To configure general Bluetooth LE settings // Set for LE uncoded PHY with 1 Msymbol/s modulation. :SOURce1:BB:BTOoth:BMODe BLEN :SOURce1:BB:BTOoth:PFORmat // Query the version of the Bluetooth standard. :SOURce1:BB:BTOoth:VERSion? // Response: "6.0". :SOURce1:BB:BTOoth:STATe ON // Generate and save a waveform file in the current directory.
Page 163 ® Remote control commands R&S SMBVB-K60/-K117/-K178 General commands Initiator (only advertising channel type) CONNECT_IND Within R&S SMBVB-K117 also AUX_CONNECT_REQ, AUX_CONNECT_RSP Example: Example "To configure general Bluetooth BR/EDR settings" on page 161. Usage: Query only Manual operation: "Bluetooth Controller State" on page 48 [:SOURce<hw>]:BB:BTOoth:BMODe <BMode>...
Page 164 ® Remote control commands R&S SMBVB-K60/-K117/-K178 General commands Example: Example "To save and recall settings" on page 161. Manual operation: "Save/Recall" on page 35 [:SOURce<hw>]:BB:BTOoth:SETTing:DELete <Filename> Deletes the selected file from the default or specified directory. Deleted are files with the file extension *.bto.
Page 165 ® Remote control commands R&S SMBVB-K60/-K117/-K178 General commands Example: Example "To configure general Bluetooth BR/EDR settings" on page 161. Manual operation: "State" on page 34 [:SOURce<hw>]:BB:BTOoth:TMODe <TMode> Selects the transport mode. Parameters: <TMode> ACL | SCO | ESCO Asynchronous connection-less (ACL) mode used for a point-to- point multipoint link between a Central and all Peripherals.
Page 166: Dirty Transmitter Configuration
® Remote control commands R&S SMBVB-K60/-K117/-K178 Dirty transmitter configuration Version 5.5 requires R&S SMBVB-K178. Manual operation: "Bluetooth Version" on page 36 [:SOURce<hw>]:BB:BTOoth:WAVeform:CREate <Filename> Saves the current settings as an ARB signal in a waveform file (*.wv). Setting parameters: <Filename> string Example: Example "To configure general Bluetooth BR/EDR settings"...
Page 167 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Dirty transmitter configuration Commands: ..............167 [:SOURce<hw>]:BB:BTOoth:DTTest:DTTState ..............167 [:SOURce<hw>]:BB:BTOoth:DTTest:FDDeviation ..............167 [:SOURce<hw>]:BB:BTOoth:DTTest:FDRate ..............168 [:SOURce<hw>]:BB:BTOoth:DTTest:MIMode ..............168 [:SOURce<hw>]:BB:BTOoth:DTTest:NPPSet ..............169 [:SOURce<hw>]:BB:BTOoth:DTTest:SPHase ..............169 [:SOURce<hw>]:BB:BTOoth:DTTest:STDefault ..............169 [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe ......169 [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:CFOFfset .........170 [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:MINDex ........171 [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:STATe ........ 171 [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:STERror ......
Page 168 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Dirty transmitter configuration A sine wave is used to drift the modulated Bluetooth signal around center frequency + carrier frequency offset with the set frequency drift rate. Parameters: <FdRate> 0.3 KHz | 0.5 KHz | 1.6 KHz | 10 KHz Range: depends on packet type to depends on packet type...
Page 169 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Dirty transmitter configuration [:SOURce<hw>]:BB:BTOoth:DTTest:SPHase <SPhase> The command enters a start phase. The start phase applies to the sine wave that is used to drift the modulated Bluetooth signal. The drift is around the center frequency plus the carrier frequency offset. Parameters: <SPhase>...
Page 170 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Dirty transmitter configuration Parameters: <CfOffset> integer Range: -150 to 150 *RST: Default unit: kHz Example: SOURce1:BB:BTO:PTYP DH1 sets the packet type. SOURce1:BB:BTO:DTT:TABL LONG sets the table type SOURce1:BB:BTO:DTT:TABL:LONG:SET2:CFOF 14 sets a carrier frequency offset. Example: See also Example "To configure a dirty transmitter"...
Page 171 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Dirty transmitter configuration [:SOURce<hw>]:BB:BTOoth:DTTest:TABLe:LONG:SET<ch>:STATe <State> Activates the corresponding parameter set for the long table. For basic rate packets, each set applies to 20 ms of signal. Parameters: <State> 1 | ON | 0 | OFF *RST: Example: SOURce1:BB:BTO:PTYP DH1...
Page 172 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Dirty transmitter configuration Parameters: <CfOffset> integer Range: -150 to 150 *RST: Default unit: kHz Example: SOURce1:BB:BTO:PTYP DH1 sets the packet type. SOURce1:BB:BTO:DTT:TABL SHOR sets the table type SOURce1:BB:BTO:DTT:TABL:SHOR:SET2:CFOF 65 sets a carrier frequency offset. Example: See also Example "To configure a dirty transmitter"...
Page 173: Channel Configuration Commands - Le
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel configuration commands - LE Example: SOURce1:BB:BTO:PTYP DH1 sets the packet type. SOURce1:BB:BTO:DTT:TABL SHOR enters the table type SOURce1:BB:BTO:DTT:TABL:SHOR:SET2:STER 20 enters a symbol timing error. Example: See also Example "To configure a dirty transmitter" on page 166.
Page 174 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel configuration commands - LE Depending on the selected channel type different roles are assigned to the controller. For channel type "Data", you can assign Central or Peripheral. If the channel type is "Advertising", the parameter is read only and displayed directly above the graph.
Page 175 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel configuration commands - LE *RST: ADVertising Example: Example "To configure general channel settings for LE" on page 173. Manual operation: "Channel Type" on page 45 [:SOURce<hw>]:BB:BTOoth:DCYCle <DCycle> Specifies duty cycle for directed advertising (packet type ADV_DIRECT_IND). Parameters: <DCycle>...
Page 176 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel configuration commands - LE [:SOURce<hw>]:BB:BTOoth:UPTYpe <UpType> Selects the packet type. The available packets depend on the selected channel type and installed options. The tables below provide an overview. Table 8-1: R&S SMBVB-K60 packet/PDU types <UpType>...
Page 177 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel configuration commands - LE Table 8-3: R&S SMBVB-K178 packet/PDU types <UpType> Packet/PDU type <UpType> Packet/PDU type CSSEq CS_SEQUENCE CSREQ LL_CS_REQ CSRQ LL_CS_SEC_REQ CSRSP LL_CS_RSP CSRP LL_CS_SEC_RSP CSIND LL_CS_IND CCRQ LL_CS_CAPABILITIES_REQ LL_CS_TERMINATE_IND CCRP LL_CS_CAPABILITIES_RSP CFRQ LL_CS_FAE_REQ COREQ...
Page 178 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel configuration commands - LE Parameters: <UsLength> integer Range: depends on the number of states in dirty transmitter test to dynamic *RST: Example: Example "To configure general channel settings for LE" on page 173. Manual operation: "Sequence Length"...
Page 179: Event And Frame Configuration Commands - Le
® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE Example: Example "To configure general channel settings for LE" on page 173. Manual operation: "Duration" on page 48 8.4 Event and frame configuration commands - LE Example: Configure event and frame configuration settings // ****************************************************************** // For ADV_SCAN_IND, select advertising event interval.
Page 180: Advertising Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE // ****************************************************************** // Alternatively select packet type LL_CONNECTION_UPDATE_IND, // set transmit window, start point of the transmit // window, LL connection timeout and time interval. // ****************************************************************** SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe CUR SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:NWSize 8.25...
Page 181 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:AEDelay <AeDelay> Sets a time delay between the start times of two consecutive advertising events. The value is added to the advertising event interval. Command sets the values in ms. Query returns values in s. Parameters: <AeDelay>...
Page 182 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE Parameters: <AeInterval> float Range: 5E-3 s to depends on oversampling Increment: 0.1E-3 *RST: 20E-3 Default unit: ms Example: SOURce1:BB:BTO:ECON:AEIN 15 Sets a time interval of 15 ms. Example: See also Example "Configure event and frame configuration set-...
Page 183 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE Example: SOURce1:BB:BTO:ECON:LCM UENC without encoding. SOURce1:BB:BTO:ECON:LCM ENC in encrypted mode. Example: See also Example "Configure event and frame configuration set- tings" on page 179. Manual operation: "LL Connection Mode" on page 54 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:LTKey <LtKey>, <BitCount>...
Page 184 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MXINterval <MInterval> Specifies the maximum allowed connection interval. Command sets the values in ms. Query returns values in s. Parameters: <MInterval> float Range: 7.5E-3 s to 4000E-3 s Increment: 1.25E-3 *RST: 7.5E-3...
Page 185 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE Example: SOURce1:BB:BTO:ECON:PCON:OFFSet0:VALue 7 SOURce1:BB:BTO:ECON:PCON:OFFSet0:VALue? // Response: "7.5" Sets the Offset0 to 7.5 ms. The setting 7 ms is automatically changed to the closest multiple of 1.25 ms, which is 7.5 ms. Example: See also Example "Configure event and frame configuration set-...
Page 186 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:RCECount <RCECount> Specifies the ReferenceConnEventCount field of LL_CONNECTION_PARAM_REQ. Parameters: <RCECount> integer Range: 0 to 65535 *RST: Example: Example "Configure event and frame configuration settings" on page 179. Options: R&S SMBVB-K117 Manual operation:...
Page 187 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:SINTerval <SInterval> Sets the time interval between the starting points of two consecutive windows during which the scanner is operating in an advertising channel. Command sets the values in ms. Query returns values in s. Parameters: <SInterval>...
Page 188: Channel Table Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE Return values: <WoInfo> string Example: SOURce1:BB:BTO:UPTY CREQ Sets packet type CONNECT_IND SOURce1:BB:BTO:ECON:PCON:WOIN? Queries the start point of the transmit window. Example: See also Example "Configure event and frame configuration set- tings"...
Page 189 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Event and frame configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:ACTable:CHANnel<ch0>: CFRequency? [:SOURce<hw>]:BB:BTOoth:ECONfiguration:DCTable:CHANnel<ch0>: CFRequency? Queries the center frequency for advertising or data channels. Return values: <CenterFrequency> float Range: 2402 to 2480 Increment: 2 *RST: 2402 Example: :SOURce1:BB:BTOoth:ECON:ACTable:CHAN0:CFR? // Response in MHz: "2404"...
Page 190: Channel Sounding Commands - Le
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Usage: Query only Manual operation: "Channel Type" on page 57 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:ACTable:CHANnel<ch0>:STATe <State> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:DCTable:CHANnel<ch0>:STATe <State> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DCMTable: CHANnel<ch0>:STATe <State> Indicates used and unused data channels. Note: The previously used syntax ..:SET<ch>:STATe has been replaced by ...:CHANnel<ch>:STATe.
Page 191: Cs General Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE 8.5.1 CS general commands Example: To configure CS sequence settings :SOURce1:BB:BTOoth:CINTerval 10 // The connection interval is 10 microseconds. :SOURce1:BB:BTOoth:EINTerval 2 // The number of event intervals is two. :SOURce1:BB:BTOoth:EOFFset? // Response: "500"...
Page 192 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Manual operation: "Event Intervals/Event_Interval" on page 49 "Event_Interval" on page 124 "Event_Interval" on page 127 [:SOURce<hw>]:BB:BTOoth:CS:EOFFset <EventOffset> Sets the time between the anchor point of the LE connection event and the beginning of the CS event.
Page 193: Cs Subevent Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE 8.5.2 CS subevent commands Example: To configure CS subevent settings // ***************************************************************************** // Configure general settings of a CS subevent. // ***************************************************************************** // Configure general subevent settings. :SOURce1:BB:BTOoth:CS:SLENgth 1250 // CS subevent sequence length is 1250 microseconds.
Page 194 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE ............... 195 [:SOURce<hw>]:BB:BTOoth:CS:SNUMber ................195 [:SOURce<hw>]:BB:BTOoth:CS:NTFCs ...........195 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:NOSTep ..........196 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SSPace? ............196 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:TFCS ..........196 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MZSTeps [:SOURce<hw>]:BB:BTOoth:CS:SLENgth <SubLength> Sets the subevent length that is the duration of a CS subevent. You can set values in multiples of 625 µs.
Page 195 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE AUTO Automatic CS step scheduling. The subevent length, the sube- vent interval and the number of subevents are configurable. The number of CS steps is 2. MANual Manual CS step scheduling. The subevent length is 1250 µs, the subevent interval is 0 µs and the number of subevents is 1.
Page 196 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Example: Example "To configure CS steps for subevent 0" on page 197. Manual operation: "Number of Steps" on page 94 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SSPace? Queries the subevent space in microseconds. Return values: <SubeventSpace>...
Page 197: Cs Step Configuration Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE 8.5.3 CS step configuration commands Example: To configure CS steps for subevent 0 // Configure general CS step settings of the first subevent "Subevent 0". :SOURce1:BB:BTOoth:CS:SLENgth 1250 // CS subevent sequence length is 1250 microseconds. :SOURce1:BB:BTOoth:CS:INTerval 1875 // CS subevent interval is 1875 microseconds.
Page 198 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE For an overview on available submodes per main mode, see Table 5-8. Parameters: <mainMode> MODE1 | MODE2 | MODE3 MODE1 Mode-1 mode with no submode available. MODE2 Mode-2 mode with submodes Mode-1 and Mode-3 available. MODE3 Mode-3 mode with submodes Mode-1 and Mode-2 available.
Page 199 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Example: Example "To configure CS subevent settings" on page 193. Manual operation: "Main_Mode_Min_Steps" on page 101 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MMSTeps? Queries the number of main mode CS steps. Return values: <MMSTeps> integer Range: 2 to 160 *RST:...
Page 200 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Parameters: <TIPO> TIP1_10 | TIP1_20 | TIP1_30 | TIP1_40 | TIP1_50 | TIP1_60 | TIP1_80 | TIP1_145 TIP1_x, x represents values in microseconds. *RST: TIP1_145 Example: Example "To configure CS subevent settings" on page 193.
Page 201 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Manual operation: "T_PM" on page 105 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTHRee:TIPT <TIPT> [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTWO:TIPT <TIPT> Sets the time "T_IP2" for Mode-2 or Mode-3 CS steps. Parameters: <TIPT> TIP2_10 | TIP2_20 | TIP2_30 | TIP2_40 | TIP2_50 | TIP2_60 | TIP2_80 | TIP2_145 TIP2_x, x represents values in microseconds.
Page 202 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Manual operation: "Sequence Length" on page 103 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:UPAYload <UserPayload> Selects a data list file as the data source for a random CS sequence. This sequence uses the CS_SYNC_User_Payload for CS step configuration modes Mode-1 or Mode-3.
Page 203: Cs Step Info Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE 8.5.4 CS step info commands Example: To configure CS step settings for a subevent // ***************************************************************************** // Configure general settings of a CS subevent. // ***************************************************************************** // Configure general subevent settings. :SOURce1:BB:BTOoth:CS:SLENgth 1250 // CS subevent sequence length is 1250 microseconds.
Page 204 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CINDex <ChannlIndex> Queries the channel index for individual CS steps. Parameters: <ChannlIndex> integer Range: 0 to 78 *RST: Example: Example "To configure CS step settings for a subevent" on page 203. Manual operation: "Channel Index"...
Page 205 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE <BitCount> integer Range: 32 to 128 *RST: Example: Example "To configure CS step settings for a subevent" on page 203. Manual operation: "Sounding Sequence Content/Random Sequence Content" on page 110 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CSIGnal <CompanionSignal>...
Page 206: Cs Channel Table Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Select the file from the default instrument directory or a specific directory. Parameters: <DataList> string Example: Example "To configure CS step settings for a subevent" on page 203. Manual operation: "Companion Signal"...
Page 207 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Return values: <CenterFreq> float For a description, see also table Table 2-13. Range: 2402 to 2480 Increment: 2 *RST: 2402 Example: Example "To configure CS subevent settings" on page 193. Usage: Query only Manual operation:...
Page 208: Cs Security Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE 1|ON Enables transmission of the subevent for the selected channel. 0|OFF Disables transmission of the subevent for the selected channel. *RST: Example: Example "To configure CS subevent settings" on page 193. Manual operation: "Channel Allowed"...
Page 209 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE <BitCount> integer Fixed bit count of 64 bits. Range: 64 to 64 *RST: Example: Example "To configure CS subevent settings" on page 193. Manual operation: "CS_IV_P(hex)" on page 97 [:SOURce<hw>]:BB:BTOoth:CS:CINC <CsInC>, <BitCount>...
Page 210: Cs Channel Selection Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CSPVc <csPvC> Parameters: <csPvC> 64 bits Manual operation: "CS_PV_C(hex)" on page 98 [:SOURce<hw>]:BB:BTOoth:CS:CPVP <CsPvP>, <BitCount> Requires packet type CS SEQUENCE or LL_CS_SEC_REQ. Sets the CS_PV_P parameter. The parameter is 64-bit in hexadecimal representation. Parameters: <CsPvP>...
Page 211 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel sounding commands - LE Return values: <CsFilteredChM> numeric CSFilteredChM value in hexadecimal representation. *RST: Example: Example "To configure CS subevent settings" on page 193. Usage: Query only Manual operation: "CSFilteredChM(hex)" on page 98 [:SOURce<hw>]:BB:BTOoth:CS:CMRepetition <ChMRepetition>...
Page 212: Packet Configuration Commands - Le
® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Parameters: <ChThreeCJump> JUMP_2 | JUMP_3 | JUMP_4 | JUMP_5 | JUMP_6 | JUMP_7 | JUMP_8 For Ch3cJump field parameters, see Table 5-7. *RST: JUMP_2 Example: Example "To configure CS subevent settings" on page 193.
Page 213 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE // ****************************************************************** // Alternatively set periodic advertising interval for AUX_SYNC_IND // ****************************************************************** SOURce1:BB:BTOoth:CTYPe ADV SOURce1:BB:BTOoth:UPTYpe ASIN SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:PAINterval // ****************************************************************** // Select packet type AUX_ADV_IND. (All parameters of // extended header are configurable with AUX_ADV_IND packet // type.) Set channel selection, // Tx device address type, advertising mode.
Page 214 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:ADID #H01FF,12 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:ASID #H0F,4 // ****************************************************************** // Enable and specify AuxPtr for the secondary advertising // channel: select AUX channel, set clock accuracy, offset unit, // AUX offset, AUX PHY. // ****************************************************************** SOURce1:BB:BTOoth:ECONfiguration:PCON:EHFLags:APTR:STATe ON SOURce1:BB:BTOoth:ECONfiguration:DCTable:CHANnel0:STATe 1...
Page 215 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: To configure data packets // ****************************************************************** // Configure signal for DATA: select channel type, packet type, // packet format, sequence length, role, enable CRC corruption. // ****************************************************************** SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe CUR SOURce1:BB:BTOoth:PFORmat L1M SOURce1:BB:BTOoth:USLength 12...
Page 216 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit1:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit2:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit3:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit4:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit5:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit6:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit7:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit8:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit9:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit10:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit11:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit12:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit13:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit14:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit15:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit16:STATe 0 // ****************************************************************** // Configure the payload of LL_CONNECTION_PARAM_REQ: max.
Page 217 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE // ****************************************************************** // Set the payload of LL_PHY_REQ: specify preferred Tx, Rx PHYs. // ****************************************************************** SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe PREQ SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L1M:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L2M:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:LCOD:STATe 0 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:RPHYs:L1M:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:RPHYs:L2M:STATe 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:RPHYs:LCOD:STATe 0 // ****************************************************************** // Set the payload of LL_PHY_UPDATE_IND: specify PHYs for...
Page 218: General Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE // configure CTE method, set event counter properties, specify PHYs // and address type. // ****************************************************************** SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe PSIN SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:CPResent 1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:CTIMe 0.016 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:CTYPe AOD1 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:ANTNumber 4 SOURce1:BB:BTOoth:ECONfiguration:PCONfiguration:ANTGain0? // Response: "0"...
Page 219 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DWHitening <DWhitening> Activates or deactivates the Data Whitening. Evenly distributed white noise is ideal for the transmission and real data can be forced to look similar to white noise with different methods called Data Whitening.
Page 220: Header Configuration
® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE 8.6.2 Header configuration ......220 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CSELection ....... 220 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NSValue ....... 220 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SSValue ......221 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CPResent ........221 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTIMe ......... 221 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTReq ......... 222 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTYPe ......... 222 [:SOURce<hw>]:BB:BTOoth:ECONfig:PCONfig:ANTGain<ch0> ..........222 [:SOURce<hw>]:BB:BTOoth:ECONfig:PCONfig:ANTNumber [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CSELection <CSelection>...
Page 221 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: Example "To configure data packets" on page 215. Manual operation: "SN Start Value" on page 60 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CPResent <State> Activates the CTEInfo field in the header of Bluetooth LE data packets in the LE unco- ded PHY.
Page 222 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CTYPe <CType> Sets the type of constant tone extension. The type specifies the CTE AoA/AoD method and for AoD the length of the switching and I/Q sampling slots. Parameters: <CType>...
Page 223: Payload Configuration
® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE 8.6.3 Payload configuration ........225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD ....225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:APATtern ....226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:ASELection ........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACID ......226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACASsigned ......226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SCASsigned ........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SCID ......226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ICASsigned ........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ICID ........227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ADID ........227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALAP ........227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ILAP...
Page 224 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE ....... 238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SIVector ......239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MROCtets ......239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTOCtets ........239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MSKD ........239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SSKD ....... 240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MRTime ........240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTTime ......240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MUCHannels ....240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:L1M:STATe ....240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:L2M:STATe ... 240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:LCOD:STATe ....240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:L1M:STATe ....240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:L2M:STATe...
Page 225 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE ....251 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PHY:LCOD:STATe ......251 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SCECounter ........252 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SID [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD <Data> Specifies the pattern source used for additional controller advertising data (ACAD). Parameters: <Data> ALL0 | ALL1 | PATTern | PN09 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt ALL0 / ALL1 All 0 or all 1 pattern...
Page 226 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "AList / Pattern" on page 70 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:ASELection <DSelection> Specifies data list file. The settings is relevant for [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACADDLISt Parameters: <DSelection> string Path and file name. Example: Example "To configure advertising packets" on page 212.
Page 227 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE <BitCount> integer Range: 24 to 24 *RST: Example: Example "To configure advertising packets" on page 212. Manual operation: "Initiator's Device Addr" on page 76 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ADID <Adid>, <BitCount> Specifies "Advertising Data ID" in hexadecimal format to be signaled within an exten- ded header.
Page 228 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "Target's Device Addr" on page 64 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALENgth <Length> Specifies the length of ACAD data pattern. Parameters: <Length> integer Range: 0 to 62 *RST: Example: Example "To configure advertising packets" on page 212.
Page 229 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE <BitCount> integer Range: 24 to 24 *RST: Example: Example "To configure advertising packets" on page 212. Options: R&S SMBVB-K117 Manual operation: "Target's Device Addr" on page 64 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AOFFset <AOffset> Specifies the time from the start of the packet containing the AuxPtr field to the approx- imate start of the auxiliary packet.
Page 230 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Parameters: <APhy> L1M | L2M | LCOD | L2M2B For a description, see [:SOURce<hw>]:BB:BTOoth:PFORmat on page 175. *RST: Example: Example "To configure advertising packets" on page 212. Options: L2M and LCOD require option R&S SMBVB-K117. L2M2B requires option R&S SMBVB-K178.
Page 231 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:CID <Cid>, <BitCount> Sets the company identifier of the manufacturer of the Bluetooth Controller. A 16 bit value is set. Note: This parameter is relevant for data frame configuration and for the packet type LL_VERSION_IND.
Page 232 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "Connection Event Interval" on page 54 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DATA <Data> Selects the pattern source used for the payload. Parameters: <Data> ALL0 | ALL1 | PATTern | PN09 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt ALL0 / ALL1 All 0 or all 1 pattern...
Page 233 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:DATA:DSELection <DSelection> Selects a data list file from the default directory or from the specific directory. Using data list (DLISt) data requires one of the following commands: ● BB:BTO:ECON:PCON:DATA DLISt [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration: on page 232.
Page 234 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE <BitCount> integer Range: 8 to 8 *RST: Example: SOURce1:BB:BTO:ECON:PCON:ECOD #H00,8 Sets the error code. Manual operation: "Error Code(hex)" on page 81 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ECOunter <ECounter> Counts the AUX_SYNC_IND packets that the SyncInfo field describes. Parameters: <ECounter>...
Page 235 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: Example "To configure advertising packets" on page 212. Options: R&S SMBVB-K117 Manual operation: "Extended Header" on page 67 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:EHFLags: AADDress:STATe <State> If enabled, the R&S SMBV100B includes the signaling of non-significant advertising address part (NAP) and upper address part (UAP).
Page 236 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:EHFLags:CINFo: STATe <State> Activates the CTEInfo field in the extended header of Bluetooth LE advertising packets in the LE uncoded PHY. Parameters: <State> 1 | ON | 0 | OFF *RST: Example: Example "To configure advertising packets"...
Page 237 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: Example "To configure advertising packets" on page 212. Options: R&S SMBVB-K117 Manual operation: "TxPow(dBm)" on page 69 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit<ch0>:STATe <State> Requires link layer control PDUs LL_FEATURE_REQ, LL_FEATURE_RSP or LL_PERIPHERAL_FEATURE_REQ, see [:SOURce<hw>]:BB:BTOoth:UPTYpe on page 176.
Page 238 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE The Central and Peripherals determine the data channel in use for every connection event from the channel map. Hop_length is set for the LL connection and communica- ted in the CONNECT_IND and LL_CHANNEL_MAP_IND packets. Parameters: <HLength>...
Page 239 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: SOURce1:BB:BTO:ECON:PCON:MIV #H0000000000000000,32 (Central). SOURce1:BB:BTO:ECON:PCON:SIV #H0000000000000000,32 (Peripheral). [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MROCtets <MROctets> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTOCtets <MTOctets> Specifies the maximum allowed payload length of a packet to be received (..:MROCtets) or transmitted (..:MTOCtets). Information is signaled via LL_LENGTH_REQ and LL_LENGTH_RSP.
Page 240 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MRTime <MRTime> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTTime <MTTime> Specifies the maximum allowed time to receive (..:MRTime) or transmit (..:MTTime) a packet. Information is signaled via LL_LENGTH_REQ and LL_LENGTH_RSP. Parameters: <MTTime> float Range: 0.328E-3 to 17.04E-3 Increment: 0.001E-3 *RST: 17.04E-3...
Page 241 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE You can enable one or more PHYs: ● L1M: for LE uncoded 1 Msymbol/s PHY. ● L2M: for LE uncoded 2 Msymbol/s PHY. ● LCOD: for LE coded 1 Msymbol/s PHY. Parameters: <STMP>...
Page 242 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:NSLatency <NsLatency> Requires a data event and advertising frame configuration with the packet type LL_CONNECTION_UPDATE_IND. Sets the number of consecutive connection events the Peripheral can ignore for asym- metric link layer connections. Parameters: <NsLatency>...
Page 243 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: Example "To configure data packets" on page 215. Manual operation: "Transmit Window Size" on page 76 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:OADJust <State> Adjusts the "Sync Packet Offset" automatically to the next value, which is a multiple of the ""Offset Units".
Page 244 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Depending on the Bluetooth controller role either Tx or Rx or both address types are assigned. Subdivided into private and random, a Bluetooth LE device address consits of 48 bits. The format of the device address differs depending on the selected address type.
Page 245 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L2M:STATe <TPhys> [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:LCOD: STATe <TPhys> Specifies preferred physical layers in Rx (..:RPHYs:..) or Tx (..:TPHYs:..) direc- tion. Information is signaled via LL_PHY_REQ and LL_PHY_RSP. You can enable one or more PHYs: :L1M: for LE uncoded 1 Msymbol/s PHY, :L2M: for LE uncoded 2 Msymbol/s PHY, and :LCOD: for LE coded 1 Msymbol/s PHY.
Page 246 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: SOURce1:BB:BTO:ECON:PCON:SCAC SCA1 Sets the encoding value. Manual operation: "Sleep Clock Accuracy" on page 78 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SLATency <SLatency> Requires data event and advertising frame configuration with the packet type CON- NECT_IND.
Page 247 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPOFfset <SPOffset> Specifies the time from the start of the AUX_ADV_IND packet containing the SyncInfo field to the start of the AUX_SYNC_IND packet. The offset is determined by multiplying the value by the unit, see [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SOUNits Parameters:...
Page 248 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "TxPow(dBm)" on page 69 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:UTYPe <UType>, <BitCount> Enables that an invalid control packet is indicated. The CtrType field indicates the value of the LL control packet that caused the transmis- sion of this packet.
Page 249 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Parameters: <WOffset> float Range: 0 s to depending on connection event interval Increment: 1.25E-3 s *RST: Default unit: ms Example: Example "Configure event and frame configuration settings" on page 179. Manual operation: "Transmit Window Offset"...
Page 250 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: Example "To configure data packets" on page 215. Manual operation: "Connection Event Count" on page 87 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ID <Id>, <BitCount> Specifies the ID in the CtrData field of the LL_PERIODIC_SYNC_IND PDU. Parameters: <Id>...
Page 251 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:PHY:L1M:STATe <State> Sets the LE 1M PHY in the CtrData field of the LL_PERIODIC_SYNC_IND PDU. Parameters: <State> 1 | ON | 0 | OFF *RST: Example: Example "To configure data packets" on page 215.
Page 252: Cs Payload Configuration
® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SID <Sid>, <BitCount> Specifies the SID in the CtrData field of the LL_PERIODIC_SYNC_IND. Parameters: <Sid> numeric *RST: <BitCount> integer Range: 4 to 4 *RST: Example: Example "To configure data packets" on page 215.
Page 253 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE // ***************************************************************************** // Configure and check LL_CS_CAPABILITIES_REQ PDU settings. // ***************************************************************************** :SOURce1:BB:BTOoth:CS:CDATA:CSPCapability? // Response: "LE2M" // The PHY is LE 2M. :SOURce1:BB:BTOoth:CS:CDATa:MAPath 1 :SOURce1:BB:BTOoth:CS:CDATa:MPSupported 1 :SOURce1:BB:BTOoth:CS:CDATa:MTYPe? // Response: "MODE3" // The mode type is Mode-3.
Page 254 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE :SOURce1:BB:BTOoth:CS:CDATa:ECODe #HFF,8 // Sets the error code "FF" in hexadecimal representation. // ***************************************************************************** // Configure and check LL_CS_IND PDU settings. // ***************************************************************************** :SOURce1:BB:BTOoth:CS:CDATa:EOFFset 500 // Sets an event offset of 500 microseconds. // ***************************************************************************** // Configure and check LL_CS_REQ PDU settings.
Page 255 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE ...............264 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RAONly ............265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RCAPability ..............265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RFU ..............265 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RTYPe ..............266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TFCS ..............266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TIONe ..............266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TITWo ..............266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TPM ..............267 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TSW ............267 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RRSequence ............267 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:RSOunding ............268 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SINTerval .............
Page 256 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "T_IP1_Capability Table" on page 117 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TIPT:CAPability <TITCapability> Enables the T_IP2 capability including the T_IP2 time per bit position. Suffix: BPOSition<ch0> 0 to 7 Bit position (optional suffix) Parameters: <TITCapability>...
Page 257 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:ACI <ACI> Sets the antenna configuration index (ACI) field. The value has a length of 1 octet or 0 to 7 in decimal representation. Parameters: <ACI> ACI0 | ACI1 | ACI2 | ACI3 | ACI4 | ACI5 | ACI6 | ACI7 *RST: ACI0 Example:...
Page 258 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "Config_ID" on page 119 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSAThreec <CsaThreec> Enables the channel selection algorithm #3c. Parameters: <CsaThreec> 1 | ON | 0 | OFF *RST: Example: Example "To configure CS control PDUs" on page 252.
Page 259 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Example: Example "To configure CS control PDUs" on page 252. Manual operation: "Offset" on page 127 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MAPath <MaxAntPath> Sets the maximum Num_Ant paths. Parameters: <MaxAntPath> integer Range: 1 to 4 *RST: Example: Example "To configure CS control PDUs"...
Page 260 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Parameters: <MainMode> MODE1 | MODE2 | MODE3 For a description, see [:SOURce<hw>]:BB:BTOoth:CS[: on page 197. SEVent<ch0>]:MMODe *RST: MODE1 Example: Example "To configure CS control PDUs" on page 252. Manual operation: "Main_Mode"...
Page 261 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MTYPe? Queries the CS LL control packet mode type that is Mode-3. Return values: <ModeType> MODE3 *RST: MODE3 Example: Example "To configure CS control PDUs" on page 252. Usage: Query only Manual operation: "Mode_Types"...
Page 262 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:NFAE <NoFae> Sets the No_FAE bit. This bit indicates if the transmitting LE device supports a frac- tional frequency offset actuation error (FAE) or not. Parameters: <NoFae> 1 | ON | 0 | OFF 1|ON The transmitting LE device only supports an FAE of zero.
Page 263 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:OMAX <OffsetMax> Sets the time value of the Offset_Max field. The value has a length of 3 octets or 9 bits. Parameters: <OffsetMax> integer Range: 500 to 16777215 *RST: Example: Example "To configure CS control PDUs"...
Page 264 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:CS:CDATa:PHY? Queries the PHY field value. This value indicates the TX PHY of the remote device to which the Pwr_Delta field in this PDU applies. Return values: <Phy> L1M | L2M | LCOD | L2M2B For a description, see [:SOURce<hw>]:BB:BTOoth:PFORmat on page 175.
Page 265 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE :SOURce1:BB:BTOoth:CS:CDATa:RCAPability See also the table Table 5-9 for an overview. Parameters: <RttAaOnly> AR150 | AR10 | AR0 *RST: AR150 Example: Example "To configure CS control PDUs" on page 252. Manual operation: "RTT_AA_Only"...
Page 266 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "RTT_Type" on page 121 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TFCS <TFcs> Sets the frequency change period (T_FCS) between consecutive CS steps. The period ranges from 15 μs to 150 μs. Parameters: <TFcs> TFCS_15 | TFCS_20 | TFCS_30 | TFCS_40 | TFCS_50 | TFCS_60 | TFCS_80 | TFCS_100 | TFCS_120 | TFCS_150 TFCS_x, x represents values in microseconds.
Page 267 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Parameters: <TPM> TPM_10 | TPM_20 | TPM_40 | TPM_652 TPM_x, x represents values in microseconds. *RST: TPM_40 Example: Example "To configure CS control PDUs" on page 252. Manual operation: "T_PM"...
Page 268 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Parameters: <RSOunding> AR150 | AR10 | AR0 *RST: AR150 Example: Example "To configure CS control PDUs" on page 252. Manual operation: "RTT_Sounding_N" on page 115 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SINTerval <SubInterval> Sets or queries the subevent interval. Setting requires BB:BTOoth:CS:SNUMber 2 or higher.
Page 269 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - LE Manual operation: "Subevent_Per_Event" on page 124 "Subevents_Per_Event" on page 127 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SPEStimate <SPEstimate> Sets the Sounding_PCT_Estimate bit. This bit indicates if the device supports phase correction term (PCT) estimates from a sounding sequence or not. Parameters: <SPEstimate>...
Page 270: Test Packet Configuration Commands - Le
® Remote control commands R&S SMBVB-K60/-K117/-K178 Test packet configuration commands - LE 8.7 Test packet configuration commands - LE Example: To configure test packets // ***************************************************************************** // Configure settings of an LE uncoded PHY test packet. // ***************************************************************************** // Set for a data channel test packet in the LE uncoded PHY. SOURce1:BB:BTOoth:CTYPe DATA SOURce1:BB:BTOoth:UPTYpe TPAC SOURce1:BB:BTOoth:PFORmat L1M...
Page 271 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Test packet configuration commands - LE Parameters: <SPB> TWO | EIGHt *RST: Example: Example "To configure test packets" on page 270. Options: R&S SMBVB-K117 Manual operation: "Symbols per a Bit" on page 130 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SYNCword <syncWord>...
Page 272 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Test packet configuration commands - LE [:SOURce<hw>]:BB:BTOoth:DTTest:TPConfiguration:TPINterval <TpInterval> Sets the time interval between two consecutive test packets, regarding the starting points. Command sets the values in ms. Query returns values in s. Parameters: <TpInterval> float Range: 0.625E-3 s to 27.5E-3 s - depends on packet char-...
Page 273: Channel Configuration Commands - Br/Edr
® Remote control commands R&S SMBVB-K60/-K117/-K178 Channel configuration commands - BR/EDR PAT6 Predefined pattern: 01010101 DLISt Binary data from data lists as a data source. Set the data list file via the following command: [:SOURce<hw>]:BB:BTOoth:ECONfiguration: on page 233 PCONfiguration:DATA:DSELection *RST: PN09 Example: Example "To configure test packets"...
Page 274: Packet Configuration Commands - Br/Edr
® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR Manual operation: "Sequence Length" on page 134 [:SOURce<hw>]:BB:BTOoth:STIMing <SlotTiming> Selects the Rx slot timing mode. Parameters: <SlotTiming> TX | LOOPback *RST: Example: BB:BTO:PTYP DH3 sets the packet type. BB:BTO:STIM LOOP selects loopback test mode.
Page 275 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR [:SOURce<hw>]:BB:BTOoth:PCONfiguration:ACKNowledgement <Acknowledgement> Sets the ARQN bit of the packet header.. Parameters: <Acknowledgement> NAK | ACK Request to retransmit the previous payload. Previous payload has been received successfully. *RST: Example: BB:BTO:PTYP DH1 selects the packet type DH1.
Page 276 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR <BitCount> integer Range: 16 to 16 *RST: Example: BB:BTO:PCON:BDAN #H0000,16 Sets the non-significant address part. Manual operation: "Bluetooth Device Address (BD_ADDR)" on page 137 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:BDAUap <BdaUap>, <BitCount> Enters the upper address part of Bluetooth Device Address. The length of UAP is 8 bits or 2 hexadecimal figures.
Page 277 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA <Data> Selects the data source used for the payload. Parameters: <Data> ALL0 | ALL1 | PATTern | PN09 | PN11 | PN15 | PN16 | PN20 | PN21 | PN23 | DLISt *RST: PN09 Example:...
Page 278 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:VDPAttern <VdPattern>, <BitCount> Sets the bit pattern for the voice data. Parameters: <VdPattern> numeric *RST: <BitCount> integer Range: 1 to 64 *RST: Example: BB:BTO:PCON:DATA:PATT Selects the data type. BB:BTO:PCON:DATA:VDPA #B010101,6 Selects the bit pattern for the voice data with the length of 24 bits.
Page 279 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DSFPacket <DsfPacket> Selects the data source for the selected packet type. Parameters: <DsfPacket> PEDit | ADATa Enables the "Packet Editor". All packet fields can be configured individually. ADAT Fills the generated packets with the selected data source. Useful if predefined data contents are loaded with a data list file or the data contents of the packet are not of interest.
Page 280 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR Manual operation: "EIR packet follows" on page 139 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:HFControl <HfControl> The command sets the FLOW bit in the header. This bit indicates start or stop of trans- mission of packets over the ACL logical transport. Parameters: <HfControl>...
Page 281 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR Parameters: <LtAddress> integer Range: 0 to 7 Increment: 1 *RST: Example: BB:BTO:PCON:PTYP DH1 sets the packet type. BB:BTO:PCON:DSFP PED enable packet editor under data source for packet BB:BTO:PCON:LTAD 0 sets the logical transport address equal zero.
Page 282 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Packet configuration commands - BR/EDR Example: BB:BTO:PCON:DSFP ADAT fills the all data under data source for packet. BB:BTO:PCON:PLEN 1 sets the packet length. Manual operation: "Packet Length" on page 142 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:SLAP <State> Activates synchronization of the lower address part (LAP) of the sync word and Blue- tooth device address.
Page 283: Filter/Clipping Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Filter/clipping commands The scan interval is equal to the scan window T w page scan (continuous nscan) and maximal 1.28s. The scan interval is maximal 1.28s. The scan interval is maximal 2.56s. *RST: Example: BB:BTO:PCON:PTYP FHS sets the packet type.
Page 284 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Filter/clipping commands .............288 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:GAUSs ............289 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:LPASs ............289 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:PGAuss ..........289 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:RCOSine ............290 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:SPHase ..............290 [:SOURce<hw>]:BB:BTOoth:SRATe:VARiation [:SOURce<hw>]:BB:BTOoth:CLIPping:LEVel <Level> Sets the limit for level clipping. This value indicates at what point the signal is clipped. It is specified as a percentage, relative to the highest level.
Page 285 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Filter/clipping commands Parameters: <State> 1 | ON | 0 | OFF *RST: Example: SOURce1:BB:BTO:CLIP:STAT ON Activates level clipping. Manual operation: "Filter/Clipping" on page 36 "State" on page 148 [:SOURce<hw>]:BB:BTOoth:FILTer:FILTers? Queries all configured baseband filters. These filters are the common GFSK baseband filter and, for some EDR packets, a DPSK filter.
Page 286 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Filter/clipping commands [:SOURce<hw>]:BB:BTOoth:FILTer:ILENgth <ILength> Sets the impulse length (the number of filter taps). Parameters: <ILength> integer Range: 1 to depends on oversampling *RST: Example: SOURce1:BB:BTO:FILT:ILEN 10 Sets the number of filter tabs to 10. Manual operation: "Impulse Length"...
Page 287 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Filter/clipping commands Example: SOURce1:BB:BTO:FILT:OSAM:AUTO ON The most sensible parameters are selected automatically. Manual operation: "Oversampling" on page 145 [:SOURce<hw>]:BB:BTOoth:FILTer:MINDex <MIndex> Queries the modulation index resulting from the entered frequency deviation value. Parameters: <MIndex> string Example: SOURce1:BB:BTO:FILT:MIND? Queries the modulation index...
Page 288 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Filter/clipping commands Parameters: <Apco25> float Range: 0.05 to 0.99 Increment: 0.01 *RST: Example: SOURce1:BB:BTO:FILT:PAR:APCO25 0.2 Sets the roll-off factor to 0.2 for filter type APCO25. Manual operation: "B*T" on page 144 "Roll Off Factor/B*T" on page 146 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:COSine <Cosine>...
Page 289 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Filter/clipping commands Parameters: <Gauss> float Range: 0.15 to 2.5 Increment: 0.01 *RST: Example: SOURce1:BB:BTO:FILT:PAR:GAUS 0.5 Sets B x T to 0.5 for the Gauss filter type for π/4 DQPSK or 8DPSK sections. Manual operation: "B*T"...
Page 290: Power Ramping Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Power ramping commands Parameters: <RCosine> float Range: 0 to 1 Increment: 0.01 *RST: Example: SOURce1:BB:BTO:FILT:PAR:RCOS 0.22 Sets the roll-off factor to 0.22 for filter type Root Cosine. Manual operation: "B*T" on page 144 "Roll Off Factor/B*T" on page 146 [:SOURce<hw>]:BB:BTOoth:FILTer:PARameter:SPHase <SPhase>...
Page 291 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Power ramping commands [:SOURce<hw>]:BB:BTOoth:PRAMping:FOFFset <FOffset> Sets the offset of the falling edge of a burst. The offset is specified by the selected number of symbols. Negative values shift the falling edge to earlier positions, which results in a correspond- ing number of skipped symbols at the end of the burst.
Page 292: Trigger Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Trigger commands Example: BB:BTO:PRAM:ROFF 8 Skips eight symbols at the beginning of the burst. Manual operation: "Rise Offset" on page 150 [:SOURce<hw>]:BB:BTOoth:PRAMping:RTIMe <RTime> Sets the ramp time, which extends the burst by a corresponding number of 0 padding symbols at the beginning and the end of a burst.
Page 293 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Trigger commands Example: To configure an internal trigger // ****************************************************************** // Configure trigger in single mode. // Set source to internal, specify signal duration // unit and duration. // ****************************************************************** SOURce1:BB:BTOoth:TRIGger:SEQuence SING SOURce1:BB:BTOoth:TRIGger:SOURce INT SOURce1:BB:BTOoth:TRIGger:SLUNit SEQ SOURce1:BB:BTOoth:TRIGger:SLUNit FRAMe SOURce1:BB:BTOoth:TRIGger:SLENgth 2...
Page 294 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Trigger commands ● SINGle = single Parameters: <Sequence> AUTO | RETRigger | AAUTo | ARETrigger | SINGle *RST: AUTO Example: Example "To configure an internal trigger" on page 293. Manual operation: "Mode" on page 152 [:SOURce<hw>]:BB:BTOoth:TRIGger:SOURce <Source>...
Page 295 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Trigger commands [:SOURce<hw>]:BB:BTOoth:TRIGger:TIME:DATE <Year>, <Month>, <Day> Sets the date for a time-based trigger signal. For trigger modes single or armed auto, you can activate triggering at this date via the following command: SOURce<hw>:BB:<DigStd>:TRIGger:TIME:STATe <DigStd> is the mnemonic for the digital standard, for example, ARB. Time-based trig- gering behaves analogously for all digital standards that support this feature.
Page 296 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Trigger commands <DigStd> is the mnemonic for the digital standard, for example, ARB. Time-based trig- gering behaves analogously for all digital standards that support this feature. Parameters: <Hour> integer Range: 0 to 23 <Minute> integer Range: 0 to 59...
Page 297 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Trigger commands Usage: Event Manual operation: "Arm" on page 153 [:SOURce<hw>]:BB:BTOoth:TRIGger:EXECute Executes a trigger. Example: Example "To configure an internal trigger" on page 293. Usage: Event Manual operation: "Execute Trigger" on page 153 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:SYNChronize:OUTPut <Output> Enables signal output synchronous to the trigger event.
Page 298: Marker Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Marker commands 8.13 Marker commands Example: To configure a marker signal // ****************************************************************** // Configure marker mode: set a marker at ARB sequence start. // ****************************************************************** SOURce1:BB:BTOoth:TRIGger:OUTPut1:MODE RESTart // SOURce1:BB:BTOoth:TRIGger:OUTPut1:MODE STARt // SOURce1:BB:BTOoth:TRIGger:OUTPut1:MODE ACTive // ****************************************************************** // Alternatively configure pulse marker.
Page 299 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Marker commands ........301 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:PULSe:DIVider ......301 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:PULSe:FREQuency? ..........302 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:RESHift [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:DELay <Delay> Defines the delay between the signal on the marker outputs and the start of the sig- nals. Parameters: <Delay> float Range: 0 to 16777215 Increment: 1 *RST: Example:...
Page 300 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Marker commands ACTive The marker masks the active part of the event/frame. At the start of each burst, the marker signal changes to high. It changes back to low after the end of each burst. PULSe A regular marker signal is generated.
Page 301 ® Remote control commands R&S SMBVB-K60/-K117/-K178 Marker commands <BitCount> integer Range: 1 to 64 *RST: Example: Example "To configure a marker signal" on page 298. Manual operation: "Mode" on page 156 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:PINDex <PIndex> For Bluetooth LE data packets higher than one, sets the packet index. The index corre- sponds to the transmitted Tx event during the connection interval.
Page 302: Clock Commands
® Remote control commands R&S SMBVB-K60/-K117/-K178 Clock commands [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:RESHift <Shift> Shifts the rising edge of the marker the specified number of samples. Negative values result in a shift back of the marker edge. Parameters: <Shift> float Range: dynamic to dynamic Increment: 1E-6 *RST: Example:...
Page 303: Glossary: Specifications
® Glossary: Specifications R&S SMBVB-K60/-K117/-K178 Glossary: Specifications Symbols [1]: Bluetooth SIG: Bluetooth Core Specification version 6.0 https://www.bluetooth.com/specifications/specs/ User Manual 1178.8120.02 ─ 09...
Page 304: List Of Commands
® List of commands R&S SMBVB-K60/-K117/-K178 List of commands [:SOURce<hw>]:BB:BTOoth:BCRole......................173 [:SOURce<hw>]:BB:BTOoth:BCText?......................162 [:SOURce<hw>]:BB:BTOoth:BMODe......................163 [:SOURce<hw>]:BB:BTOoth:CCRC:STATe....................174 [:SOURce<hw>]:BB:BTOoth:CLIPping:LEVel....................284 [:SOURce<hw>]:BB:BTOoth:CLIPping:MODE....................284 [:SOURce<hw>]:BB:BTOoth:CLIPping:STATe....................284 [:SOURce<hw>]:BB:BTOoth:CLOCk:SOURce....................302 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:ACI....................257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CCID:STATe...................257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CECount..................257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CID....................257 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSAThreec..................258 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSIGnal..................258 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:CSPCapability?................269 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:ECODe..................258 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:EOFFset..................258 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MAPath..................259 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MMASteps..................259 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:MMISteps..................
Page 305 ® List of commands R&S SMBVB-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SNUMber..................268 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:SPEStimate................... 269 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TFCS..................... 266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TIONe.................... 266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TITWo.................... 266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TPM....................266 [:SOURce<hw>]:BB:BTOoth:CS:CDATa:TSW....................267 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TFCapability.............255 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TIPO:CAPability..........255 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TIPT:CAPability..........256 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:BPOSition<ch0>]:TPCapability.............256 [:SOURce<hw>]:BB:BTOoth:CS:CDATa[:CHANnel<ch0>]:CFAE..............256 [:SOURce<hw>]:BB:BTOoth:CS:CFCHm?....................210 [:SOURce<hw>]:BB:BTOoth:CS:CINC......................209 [:SOURce<hw>]:BB:BTOoth:CS:CINP......................209 [:SOURce<hw>]:BB:BTOoth:CS:CINTerval....................191 [:SOURce<hw>]:BB:BTOoth:CS:CIVC......................208 [:SOURce<hw>]:BB:BTOoth:CS:CIVP......................208 [:SOURce<hw>]:BB:BTOoth:CS:CMRepetition..................... 211 [:SOURce<hw>]:BB:BTOoth:CS:CPVP......................210 [:SOURce<hw>]:BB:BTOoth:CS:CSEL......................211 [:SOURce<hw>]:BB:BTOoth:CS:CSPVc.......................
Page 306 ® List of commands R&S SMBVB-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTWO:TPM..............200 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MTWO:TSW?..............200 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MZERo:TIPO..............199 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:MZSTeps................196 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:NOSTep................195 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:PATTern................206 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SEQLength............... 201 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SMODe................198 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SMSTep?................199 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:SSPace?................196 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:STYPe................201 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:TFCS................196 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:UPAYload................202 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>]:UPPattern................. 202 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CAADdress..........204 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CINDex............204 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CSIGnal............205 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:CTEXtension..........206 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:MTYPe?............203 [:SOURce<hw>]:BB:BTOoth:CS[:SEVent<ch0>][:STEP<st0>]:SCONtent............ 204 [:SOURce<hw>]:BB:BTOoth:CTYPe......................174 [:SOURce<hw>]:BB:BTOoth:DCYCle......................175 [:SOURce<hw>]:BB:BTOoth:DTTest:DTTState.....................
Page 307 ® List of commands R&S SMBVB-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:APINterval................182 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:DCTable:CHANnel<ch0>:CFRequency?.......189 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:DCTable:CHANnel<ch0>:CINDex?........189 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:DCTable:CHANnel<ch0>:CTYPe?........189 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:DCTable:CHANnel<ch0>:STATe..........190 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:LCMode................. 182 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:LTKey..................183 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AADDress............219 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD............225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:APATtern.......... 225 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACAD:ASELection........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACASsigned..........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ACID............226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ADID............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALAP............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ALENgth............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AMODe............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ANUap............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AOFFset............229 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:AOUNits............229 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:APHY............229 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ASID............230 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ATYPe............
Page 308 ® List of commands R&S SMBVB-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:EHFLags:TPOWer:STATe......236 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:FSBit<ch0>:STATe........237 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:FSLength.............237 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:HLENgth............237 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ICASsigned..........226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ICID............. 226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ID..............250 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:ILAP.............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:INUap............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:LCTimeout........... 238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:LPECounter..........250 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MCLReq............250 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MIVector............238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MNINterval..........183 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MROCtets............239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MRTime............240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MSKD............239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTOCtets............ 239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:L1M:STATe........240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:L2M:STATe........240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:MTSPhy:LCOD:STATe........
Page 309 ® List of commands R&S SMBVB-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SCECounter..........251 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SCID............226 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SID.............. 252 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SIVector............238 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SLAP............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SLATency............ 246 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SNUap............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SOUNits............246 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPBit............270 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SPOFfset.............247 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SSKD............239 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SSValue............220 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:L1M:STATe........240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:L2M:STATe........240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:STMPhy:LCOD:STATe........ 240 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SVNumber...........247 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:SYNCword...........271 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TATYpe............243 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TLAP............227 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TNUap............228 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L1M:STATe........244 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:L2M:STATe........245 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPHYs:LCOD:STATe........245 [:SOURce<hw>]:BB:BTOoth:ECONfiguration:PCONfiguration:TPOWer............
Page 310 ® List of commands R&S SMBVB-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:FILTer:TYPE....................285 [:SOURce<hw>]:BB:BTOoth:MFORmat......................178 [:SOURce<hw>]:BB:BTOoth:MSETtings:FDEViation..................287 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:ACKNowledgement............... 275 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:BDALap................. 275 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:BDANap.................275 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:BDAUap.................276 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:CODevice................276 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA..................277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:DPATtern..............277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:DSELection..............277 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:VDPAttern..............278 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DATA:VDSElection..............278 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DLENgth................278 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DSFPacket................279 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:DWHitening................279 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:EIRPacketfollows..............279 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:HFControl................280 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:LFSWord................280 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:LTADdress................280 [:SOURce<hw>]:BB:BTOoth:PCONfiguration:PFControl................
Page 311 ® List of commands R&S SMBVB-K60/-K117/-K178 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:PINDex................301 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:PULSe:DIVider............301 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:PULSe:FREQuency?..........301 [:SOURce<hw>]:BB:BTOoth:TRIGger:OUTPut<ch>:RESHift............... 302 [:SOURce<hw>]:BB:BTOoth:TRIGger:RMODe..................... 294 [:SOURce<hw>]:BB:BTOoth:TRIGger:SLENgth....................296 [:SOURce<hw>]:BB:BTOoth:TRIGger:SLUNit....................296 [:SOURce<hw>]:BB:BTOoth:TRIGger:SOURce....................294 [:SOURce<hw>]:BB:BTOoth:TRIGger:TIME:DATE..................295 [:SOURce<hw>]:BB:BTOoth:TRIGger:TIME:TIME..................295 [:SOURce<hw>]:BB:BTOoth:TRIGger:TIME[:STATe]..................295 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:DELay................297 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:INHibit................297 [:SOURce<hw>]:BB:BTOoth:TRIGger[:EXTernal]:SYNChronize:OUTPut.............297 [:SOURce<hw>]:BB:BTOoth:UNIT:TIME....................... 165 [:SOURce<hw>]:BB:BTOoth:UPTYpe......................176 [:SOURce<hw>]:BB:BTOoth:USLength......................177 [:SOURce<hw>]:BB:BTOoth:VERSion?......................165 [:SOURce<hw>]:BB:BTOoth:WAVeform:CREate..................166 [:SOURce<hw>]:BB:BTOoth[:TRIGger]:SEQuence..................293 User Manual 1178.8120.02 ─ 09...
Page 312: Index
® Index R&S SMBVB-K60/-K117/-K178 Index Angle of arrival ............21 Angle of departure ............22 Access address ..............58 Data packet configuration ........... 57 ACK ................. 138 Direction finding ............21 Acknowledgment ............. 138 Settings ............... 43 ACL+EDR ................36 Test packet configuration .......... 129 Advertiser's device address ..........
Page 313 ® Index R&S SMBVB-K60/-K117/-K178 CS channel selection CS access address ........... 110 Ch3cJump ..............99 CS tone extension ............. 112 Ch3cShape ..............99 Mode type ..............109 ChM_Repetition ..........98, 120 Random sequence content ........110 ChSel ................99 Sounding sequence content ........110 CSFilteredChM ............
Page 314 ® Index R&S SMBVB-K60/-K117/-K178 FeatureSet length ..............83 Low energy Filter ................ 144, 146 Bluetooth ..............36 DPSK filter settings ........... 145 Settings ..............144 Filter parameter Marker Roll off ............... 144, 146 Delay ................. 158 Filter/clipping Mode ................. 156 Bluetooth ..............36 MIC (message authentication code) .........
Page 315 ® Index R&S SMBVB-K60/-K117/-K178 LL connection timeout ..........78 Scan window ..............52 Logical transport address ......... 137 Scanners device address ..........74 NAP ................137 SCO .................. 36 NESN start value ............60 Security procedures ............11 Packet Length ............142 Select data channel index ..........
Page 316 ® Index R&S SMBVB-K60/-K117/-K178 Symbol rate variation ............148 Symbol timing error (DTT) ..........42 Synchronize LAP with sync word ........136 Test packet configuration Bluetooth LE ............. 129 Header ..............131 Packet configuration ..........130 Packet interval ............130 Payload ..............

This manual is also suitable for:

R&s smbvb-k117 R&s smbvb-k118

Rohde & Schwarz R&S SMBVB-K60 User Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Rohde & Schwarz R&S SMBVB-K60

Summary of Contents for Rohde & Schwarz R&S SMBVB-K60

This manual is also suitable for:

Table of Contents