Haier Sea Elephant PJF2-150W User Manual page 6

Technical parameter Packing list
Technical parameter
Water-proof
Model
Volume
Grade
BRF2-150W Drip-proof
150L
Drip-proof
PJF2-150W
150L
Model Rated voltage
Frequency
230V~
BRF2-150W
50Hz
50Hz
PJF2-150W 230V~
Note: the above parameter errors ( except power value) of the lighting area are
volume errors are 3%, and the allowed error scope of other sizes is 10%.
Packing list
Packing method Name of components
Water-storing tank
Temperature and pressure valve*
Affusing liquid valve*
Small expanding bolt
Large expanding bolt
Packing container Users manual
o f w a t e r t a n k
Tee joint*
Opposite wires S1/2F-3/4M
3/4 fiber spacer
Single-direction valve*
Solar stage pothook
Expanging tank fixity
Expanding tank
Packing of solar stage
Solar stage
Packing of collector Collector equipment
Note: accessories of BRF2-150W and PJF2-150W products are suitable only for oblique
installment. For flat installment, prop stand of different angles should be made according
to requirements, which is not included in the packing accessories.The part of after which
have * will be carried by server when installation.
¼ ¯ È È Æ ÷ ° ü × ° Ï ä
Rated internal
Size
Pressure
0.7MPa
492 530 1380(mm)
0.7MPa
492 530 1380(mm)
Rated Power
Grass Collector area
Input
2
2200W 3.0m
2
4.0m
2200W
Model
BRF2-150W PJF2-150W
1
1
1
4
4
1
1
2
2
2
1
1
1
1
1
3
Use method
numbers.when set the parameter up to the
highest,press the setting key again,the
number will increase
the minimal number.to continually press
more than one second, the adjusted
parameter will increase progressively 3
numbers every second setting of each
parameter can be done by pressing the
setting key or by not pressing the setting
key about 6 seconds. Then the system will
automatically confirm and automatically
enter the next parameter setting, until the
system finally withdraws from the set
3%,
conditions and returns to the conditions of
the previous clock. The set order of
parameter in specific modes is as follows:
Solar energy heating mode:
Indicating clock condition---to check the
hour of clock---to check the minute of
clock---to set temperature difference of
water pump running--- indicating clock
c o n d i t i o n . F o r e x a m p l e : t e m p e r a t u r e
difference value setting of water pump
running: to press the setting key to enter
t h e s e t t i n g c o n d i t i o n o f t e m p e r a t u r e
difference of water pump running. The
indication board indicates the present set
value (the first place on the left of the clock
number tube indicates
following two places indicate the tacitly
approved set value, which is 15
press the setting key to select between 15
and 10 . For the indication interface,
see Fig.11.
Simultaneous heating mode:
I n d i c a t i o n c l o c k c o n d i t i o n - - - t h e
temperature of heating---indication clock
condition.
Preset heating mode:
Indicating clock condition---to set hour of
SOL H PRE
progressivelyfrom
T-DISP
ON/OFF SET
Fig.9 solar heating interface
SOL H PRE
T-DISP
ON/OFF
SET
Fig.10 turning off interface
SOL H PRE
T-DISP
SET
ON/OFF
Fig.11 temperature difference
setting interface for water pump
L , and the
). To
SOL H PRE INT
T-DISP
ON/OFF SET
Fig.12 Temperature setting interface for
The first time preset heating
12
INT WT HC
REG MODE
INT WT HC
MODE
REG
INT WT HC
Ì «
Ñ ô
Ä Ü
REG MODE
WT HC
REG MODE