Record 8000 Series Installation Instructions Manual

Swing door operator
Hide thumbs Also See for 8000 Series:

Advertisement

Quick Links

8000/8100 Series Swing Door Operator
The manufacturer's specifications for this product require the
installation to be approved by an AAADM certified inspector.
-USA
Installation Instructions
4324 Phil Hargett Court
Monroe, NC USA 28110
Http://www.record-usa.com
Toll Free: 800-438 1937
704-289-9212
Fax: 704-289-2024
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 8000 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Record 8000 Series

  • Page 1 8000/8100 Series Swing Door Operator Installation Instructions The manufacturer’s specifications for this product require the installation to be approved by an AAADM certified inspector. -USA 4324 Phil Hargett Court Toll Free: 800-438 1937 Monroe, NC USA 28110 704-289-9212 Http://www.record-usa.com Fax: 704-289-2024...
  • Page 2: Table Of Contents

    / installation dealer must perform all measurements for forces, speeds, and times to insure proper and safe operation. record-usa is not responsible for improperly adjusted or maintained aut omatic doors or activation / safety systems and assumes no responsibility for damages caused by automatic door systems that have not been properly installed, tested, and adjusted.
  • Page 3: Product Identification

    OPERATOR HANDING IDENTIFICATION Product Description The record Series 8100 Swing Door Operator is a power-open, spring-close unit providing full functionality conforming to either ANSI 156.10 or ANSI A156.19 requirements. The self- monitoring microprocessor-based control maintains precise regulation throughout the door open / close cycle.
  • Page 4: Instructions To The Installer

    This unit is to be installed and commissioned by a trained technician with knowledge of ANSI A156.19 Standards for Power Operated Doors, applicable local codes, and record-USA installation recommendations. After installation, verify the door can be opened without power applied, and the force required to open the door does not exceed 50 pounds-force (222 N).
  • Page 5: Mechanical Installation

    8000/8100 Series Swing Door Operator Installation Instructions Mechanical Installation The door panel must move freely throughout its entire opening and closing rotation. The door frame must provide a stable base, structurally sufficient to support automatic operation. Typi- cally the operator baseplate will overlap the door jambs by 1-1/2". Verify the installation conditions and select the arm configuration that most closely matches the installation.
  • Page 6: Open Stop Adjustment

    8000/8100 Series Swing Door Operator Installation Instructions Shaft Stop Open Stop Fixed Stop The unit is provided with an adjustable full open stop. Rotate the door to the full open position; mount the Shaft Stop onto the upper output shaft and against the Fixed Stop.
  • Page 7: Exploded View And Control Panel

    8000/8100 Series Swing Door Operator Installation Instructions Exploded view of a typical single swing unit The Series 8000 Standard Rocker Switch Control Panel includes: 3 Position Rocker Switch - ON / OFF / OPEN Pushbutton - To reset the operator, press and hold 8 seconds LED (red) - Normally off;...
  • Page 8: Signage

    AUTOMATIC CAUTION DOOR ACTIVATE SWITCH TO OPERATE Full Power & Low Energy Daily Safety “Knowing Act” doors Check locate below control panel AUTOMATIC CAUTION DOOR AUTOMATIC CAUTION DOOR Full Power Swing ACTIVATE SWITCH TO OPERATE Side, 2-Way Traffic; Low Energy - Sensor Activation 58”...
  • Page 9: Control Terminal Block Connections

    KeyTab Remove Jumper when connecting to a remote Fire Alarm system...
  • Page 10 Control-LED +35V +24V CANH CANL +24V +24V +24V AUX 1-IN AUX 1-OUT +24V NOT-AUS +24V +24V...

This manual is also suitable for:

8100 series

Table of Contents