1. Manuals
  2. Brands
  3. Logosol Manuals
  4. Log Splitter
  5. E37 M3
  6. User manual

Logosol E37 M3 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER MANUAL
TRANSLATION OF ORIGINAL USER MANUAL.
ITEM NO: 0458-395-0552
LOGOSOL E37 M3
Read through the user manual carefully and make sure you understand its contents
before you use the machine.
This user manual contains important safety instructions.
WARNING! Incorrect use can result in serious or fatal injuries to the operator or others.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the E37 M3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Logosol E37 M3

Summary of Contents for Logosol E37 M3

  • Page 1 USER MANUAL TRANSLATION OF ORIGINAL USER MANUAL. ITEM NO: 0458-395-0552 LOGOSOL E37 M3 Read through the user manual carefully and make sure you understand its contents before you use the machine. This user manual contains important safety instructions. WARNING! Incorrect use can result in serious or fatal injuries to the operator or others.
  • Page 2 Logosol has been manufacturing wood processing machines since 1988, and in that time we have supplied approximately 30,000 machines to satisfied customers the world over.

  • Page 3: Table Of Contents

    LOGOSOL E37 Table of contents Safety instructions Description of machine Components Use of the machine Control panel Control lever functions Position of hands during operation Assmebly Feed pressure Setting of neutral mode Operation Backward feeding Maintenance Troubleshooting Circuit diagram Exploded view...

  • Page 4: Safety Instructions

    Only use original parts supplied by units that are to be used. In addition, the Logosol which are designed for the purpose. operator must be well-rested, in good physical health, and have good eyesight. Persons that do •...

  • Page 5: Description Of Machine

    LOGOSOL E37 SAFE DISTANCES GENERAL • Check the machine on receipt. Any transport No one other than the operator is to be damage is to be immediately reported to the present within 3 metres from the sides of transport company.

  • Page 6: Components

    NÖDVÄNDIGA VERKTYG COMPONENTS The product comes unassembled in these separate parts. On delivery, check that all components of the product are included. Item no. Wire tensioner DS-00182 Drilling template DR-01382 DR-01377 Wire attachment...
  • Page 7 LOGOSOL E37 COMPONENTS 6 pcs 9018-346-1320 Flange bolt M6x20 6 pcs 9018-346-1320 Flange nut M6 Bolt bag Support leg 9018-346-1320...

  • Page 8: Use Of The Machine

    USE OF THE MACHINE Danger: When starting the feed unit, the Risk of serious injury. control lever should always be in its neutral position. Read the safety instructions Functions: With the control panel buttons you choose the desired function. During all types of processing you need to keep the enabling switch pressed down to enable operation.

  • Page 9: Control Lever Functions

    LOGOSOL E37 CONTROL LEVER FUNCTIONS Control lever: With the control lever you Operation control the feeding speed. mode Slip mode Neutral mode Risk of damaging the feed unit and the control lever. Danger: When starting the feed unit, the control lever should always be in its neutral position.

  • Page 10: Position Of Hands During Operation

    POSITION OF HANDS DURING OPERATION Forward feeding Important: For forward feeding, the enabling switch has to be pressed down when starting the feed unit. Control lever Manöverspak Hålldon Enabling switch Danger: Risk of crushing and cutting injury when the saw unit / log moulder backs in over the loading ramp.
  • Page 11 LOGOSOL E37 POSITION OF HANDS DURING OPERATION Backward feeding: Manöverspak Control lever Important: When feeding backwards, the button (B4) must be pressed down.

  • Page 12: Tools Required

    ASSEMBLY Assembly Important: Read the assembly instrunctions Sawmill symbol: first, to get an understanding of the different steps before starting the assembly. This refers to the saw This refers to the location unit’s position on the of a specific step of the sawmill.
  • Page 13 LOGOSOL E37 ASSEMBLY These instructions include assembling of the following parts of the machine.
  • Page 14 ASSEMBLY Tip: The component box shows the components that are to be used for each step of the assembly. M6x20 2 pcs 2 pcs...
  • Page 15 LOGOSOL E37 ASSEMBLY M6x20 6 pcs 6 pcs...
  • Page 16 ASSEMBLY Tip: Use a clamp to secure the drilling template to the sawmill.
  • Page 17 LOGOSOL E37 ASSEMBLY M6x16 2 pcs...
  • Page 18 ASSEMBLY Tip: When installing the feed wire, it is easier if you start at the motor side. Follow the instructions. Important: Make sure that the wire is led below the guide bolt, which is located after the pulley.
  • Page 19 LOGOSOL E37 ASSEMBLY...
  • Page 20 ASSEMBLY Tip: Be sure to tighten the wire as much as possible before fixing it to the attachment plate.
  • Page 21 LOGOSOL E37 ASSEMBLY 6 pcs...

  • Page 22: Feed Pressure

    FEED PRESSURE Important: It is important that the electric feed unit has the right feed pressure to work satidfactorily. Tighten the wire until it stops slipping in the pulley. The feeding may need to be readjusted after a period of use. Tighten the feed wire until it does not slip in the pully at the motor side.

  • Page 23: Setting Of Neutral Mode

    LOGOSOL E37 SETTING OF NEUTRAL MODE Important: The purpose of this adjustment is to ensure that the position of the control lever corresponds with the clutch. Be careful and follow the instructions. Neutral mode of the feed unit: Position the saw unit on the guide rail’s centre. Check that the control lever is in its neutral position.
  • Page 24 SETTING OF NEUTRAL MODE B4: Backward feeding Setting: When you start backward feeding (B4) the saw unit will stand still. To adjust the neutral mode, tighten the pressure bolt until the saw unit just begins to move. When this happens, you loosen the bolt slightly until the saw unit stops again.

  • Page 25: Operation

    Important: When using the saw unit and forward feeding, the enabling switch has to be pressed down. Place the material that is to be sawn on the sawmill according to the instructions in the LOGOSOL Sawmill manual. B3: Start the B4: Start the B3: Starta...
  • Page 26 OPERATION Operation mode Drift Slip mode Neutral Friläge mode Risk of damaging the feed unit and the control lever. Important: To lower the stress on the equipment, it is important that the saw unit slowly enters the wood that is to be cut.

  • Page 27: Backward Feeding

    LOGOSOL E37 BACKWARD FEEDING Important: When feeding backwards, the button (B4) is kept pressed down. The enabling switch does not have to be pressed down. The saw unit has to be turned off during this operation B4: Backward feeding Operation...

  • Page 28: Maintenance

    ’Trouble make complaints. shooting’ or contact Logosol. Normally, the power adjusting lever has to be Other maintenance adjusted a couple of times during the first working day.

  • Page 29: Lubrication Points

    LOGOSOL E37 MAINTENANCE Lubrication points Check that the ball bearings always are lubricated. Use adhesive oil in the ball bearing of the clutch. Be careful not to use too much oil. One press on the adhesive oil can nozzle gives enough lubrication (ref.

  • Page 30: Troubleshooting

    TROUBLESHOOTING Troubleshooting The feeding does not start: Do you press the enabling switch button (B5) down whi- Important: Always stop the machine if you le you are trying to feed forward? The enabling switch suspect that something is wrong with button must always be pressed down during feeding and forward machining to make the electric drive work.

  • Page 31: Circuit Diagram

    LOGOSOL E37 WIRING DIAGRAM Circuit diagram, enabling switch button with one connector block: Stop Stop Stopp Stopp H.D. Forward / back Fram/retur Drift Drive Start Start Start Start Saw unit feeding SågMatare M 3fas M 3fas Saw blade Sågklinga T.VG...

  • Page 32: Exploded View

    EXPLODED VIEW 4 x Allen bolt M6x25mm 4 x Flat washer M6 Spacer ring 12 mm Worm gear E37 Primary clutch disc Spindle m3 Friction disc: 6600-001-3024 Bearing Secondary clutch disc 2 x Angular contact ball bearing: 6600-001-3017 Hardened lock pin 30 mm m6: 6600-001-3018 Hardened lock pin 16 mm m6: 6600-001-3020 Electric motor 2 x Flat washer M6...
  • Page 33 LOGOSOL E37 EXPLODED VIEW Attachment block Flange bolt M6x16 Pulley cover Guide block Flange nut M5 Flange bolt M5 Pulley E37 6600-001-3023 Allen bolt M8x55 Hex nut M8 Guide rail Flat washer M8 FZB Locking handle Threaded rod M8x135 Ball...

  • Page 35: Ce Declaration Of Conformity

    Logosol’s products E3000 / E4000 / E5000 / E8000 / Log House Moulder 3kW. E37 Friction may not be taken into use before the Logosol sawmill and the machinery conform to the EU machine directive, which is the case if all the safety rules and instructions that come with the respective included components are followed.
  • Page 36 LOGOSOL SWEDEN Fiskaregatan 2, S-871 33 Härnösand, Sweden Phone +46 611 18285 | Fax +46 611 18289 info@logosol.se | www.logosol.se...

Table of Contents