Sunricher SRPL-2309iN-150CCT200-1050H Manual

150w dali d4i dt8 nfc enabled led driver (constant current)

Advertisement

150W DALI D4i DT8 NFC Enabled LED Driver(Constant Current)
Industrial
2
Level
Important: Read All Instructions Prior to Installation
Function introduction
AC/DC power
input
GND
ACN/
DC-
DALI DIMMABLE DRIVER
ACL/
DC+
PUSH DIM
DA
N
DA
DA
L
DA
DALI signal input
AC Push input
Product Data
LED Channel
DC Voltage
Current
200-1050mA via NFC setting; Min.current gear lower to 0.1mA
Output
Current Accuracy
Rated Power
Voltage Range
Frequency Range
Power Factor (Typ.)
Total Harmonic
Distortion
Efficiency (Typ.)
Input
AC Current (Typ.)
Inrush Current (Typ.)
Leakage Current
Standby Power Consumption
Anti Surge
Dimming Interface
Dimming Range
Control
Dimming Method
Dimming Curve
+
2
50-300V
±3%@ full load
Max. 150W
220-240VAC/VDC
0/50/60Hz
> 0.98 @ 230VAC Full load
THD ≤ 10% (@ full load / 230VAC)
>90% @ 230VAC full load
0.64A @ 230VAC
Max. 26.8A at 230VAC; 369μs duration
< 5mA /230VAC
<0.5W
L-N:4KV/ L-N-G: 4KV
DALI Device Type 8 (DALI consumption < 2mA)/ AC Push
0.1%-100%@ Max current
Amplitude/CCR dimming
Linear/ Logarithmic optional
Short Circuit
Over Current
Protection
Over Temperature
Working Temp.
Max. Case Temp.
Environment
Working Humidity
Storage Temp.
Safety Standards
WW+
WW-
CW+
Withstand Voltage
CW-
Safety &
Isolation Resistance
EMC
LED Output
EMC Emission
EMC Immunity
Others
DALI Infos
Parameter
DALI Interface Standard
Dimming Range
DA1, DA2 High Level
DA1, DA2 Low Level
DA1, DA2 Current
Bus Power Supply Voltage
Bus Power Supply Current
• In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2, IEC 62386-209
• Built-in DALI-2 interface, DALI DT8 device
• Dimmable LED driver with linear metal housing. Max. output power 150W
• 200-1050mA current selectable via NFC program tool. Min.current gear lower to 0.1mA
• DALI Address/Group/Scene setting via NFC program tool
• For luminaires of protection class I and protection class II
• High power factor and efficiency. Non-SELV rated driver
• ON/OFF, Dimming,Tunable white
• Amplitude/CCR dimming, smooth and deep dimming
• Compatible with universal DALI masters that support DT8 commands
• DALI-250/251/252/253 Enabled,DALI data inside
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty
Yes, recovers automatically after fault condition is removed
Yes, recovers automatically after fault condition is removed
Yes, recovers automatically after temperature drop
10% ~ 95% RH non-condensing
-40°C ~ +80°C, 10% ~ 95% RH
& Humidity
EN61347-1, EN61347-2-13, GB/T 19510.1-2023, GB/T 19510.213-2023
I/P-FG: 1500VAC, I/P-DA: 1500VAC, O/P-DA: 1500VAC
I/P-FG: 100M Ohms / 500VDC / 25°C / 70% RH
EN55015, EN61000-3-2, EN61000-3-3, GB 17625.1-2022, GB/T 17743-2021
EN61547, EN61000-4-2,3,4,5,6,8,11
191350H, MIL-HDBK-217F @ 230VAC full load
MTBF
and 25℃ ambient temperature
Dimension
355x30x21mm (L*W*H)
Warranty
Min.
IEC62386-101, 102, 207, 250, 251, 252, 253
0.1%
Logarithmic (default)
9.5V
-6.5V
0
12Vdc
/
-25°C ~ +60°C
Tc=90°C
5 Years
Typ.
Max.
100%
16V
22.5V
0
6.5V
2mA
16Vdc
22Vdc
55mA
60mA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SRPL-2309iN-150CCT200-1050H and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sunricher SRPL-2309iN-150CCT200-1050H

  • Page 1 150W DALI D4i DT8 NFC Enabled LED Driver(Constant Current) Short Circuit Yes, recovers automatically after fault condition is removed Over Current Industrial Protection Yes, recovers automatically after fault condition is removed Level Over Temperature Yes, recovers automatically after temperature drop Important: Read All Instructions Prior to Installation -25°C ~ +60°C Working Temp.
  • Page 2: Operation

    Operation Step 3: Unlock device, enter parameters configuring page. With DALI master Locked Unlock it 1. DALI Address 1 DALI address for 1 channel output is assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations. With NFC Programming devices Note 1) Do wiring according to the wiring diagram and power on the DALI system .
  • Page 3: Additional Remarks

    2.Enter CLO Setting homepage Step 5: After setting, please save the selected configuration via NFC and power on the device. Tips Enable CLO function Click “1",and set its time and level Set your desired time and levels. 1. NFC function doesn’t require any power driver. Graphic display 2.
  • Page 4 Wiring Diagram Safety & Warnings • DO NOT install with power applied to the device. 1. As a D4i Driver • DO NOT expose the device to moisture. DALI-2 Sensor Product Dimension ACN/ Without End Cap DALI DIMMABLE DRIVER ACL/ PUSH DIM Note: Available with 4-Wire CCT LED luminaries as well.
  • Page 5: Operating Window

    MCB Load Quantity Ipeak Twidth Max.quantity of LED Driver per MCB Module Number (max), V (500mA,300V) C16 C20 C25 D10 D16 D20 SRPL-2305iN-150CC200-1050H 26.8A 369μs (min), V (1050mA,142V) SRPL-2309iN-150CCT200-1050H 26.8A 369μs 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10...

Table of Contents