Sunricher SRPL-2305N-100CC250-1000H Manual

100w dali dt6 nfc enabled led driver (constant current)

Advertisement

100W DALI DT6 NFC Enabled LED Driver(Constant Current)
2
Important: Read All Instructions Prior to Installation
Function introduction
AC/DC power
input
GND
ACN/
DC-
DALI DIMMABLE DRIVER
ACL/
DC+
PUSH DIM
DA
N
DA
DA
L
DA
DALI signal input
AC Push input
Product Data
LED Channel
DC Voltage
Current
250-1000mA via NFC setting; Min.current gear lower to 0.1mA
Output
Current Accuracy
Rated Power
Voltage Range
Frequency Range
Power Factor (Typ.)
Total Harmonic
Distortion
Efficiency (Typ.)
Input
AC Current (Typ.)
Inrush Current (Typ.)
Leakage Current
Standby Power Consumption
Anti Surge
Dimming Interface
Dimming Range
Control
Dimming Method
Dimming Curve
1
50-220V
±3%@ full load
Max. 100W
220-240VAC/VDC
0/50/60Hz
> 0.98 @ 230VAC Full load
THD ≤ 10% (@ full load / 230VAC)
>90% @ 230VAC full load
0.5A @ 230VAC
Max. 24.2A at 230VAC; 286μs duration
< 5mA /230VAC
<0.5W
L-N:1KV/ L-N-G: 2KV
DALI Device Type 6 (DALI consumption < 2mA)/ AC Push
0.01%-100%@ Max current
Amplitude/CCR dimming
Linear/ Logarithmic optional
Short Circuit
Over Current
Protection
Over Temperature
Working Temp.
Max. Case Temp.
Environment
Working Humidity
Storage Temp.
& Humidity
Safety Standards
+
-
Withstand Voltage
Safety &
Isolation Resistance
EMC
EMC Emission
LED Output
EMC Immunity
Others
Dimension
• In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2
• Built-in DALI-2 interface, DALI DT6 device
• Dimmable LED driver with linear metal housing. Max. output power 100W
• 250-1000mA current selectable via NFC program tool. Min.current gear lower to 0.1mA
• DALI Address/Group/Scene setting via NFC program tool
• For luminaires of protection class I and protection class II
• High power factor and efficiency. Non-SELV rated driver
• To switch and dim LED lighting luminaries
• Amplitude/CCR dimming, smooth and deep dimming
• Compatible with universal DALI masters that support DT6 commands
• DALI-251/252/253 Enabled,DALI data inside
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty
Safety & Warnings
• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.
Operation
With DALI master
1. DALI Address
1 DALI address for 1 channel output are assigned by DALI Master controller automatically, please refer to user
manuals of compatible DALI Masters for specific operations.
Yes, recovers automatically after fault condition is removed
Yes, recovers automatically after fault condition is removed
Yes, recovers automatically after temperature drop
-25°C ~ +60°C
10% ~ 95% RH non-condensing
-40°C ~ +80°C, 10% ~ 95% RH
EN61347-1, EN61347-2-13, GB/T 19510.1-2023, GB/T 19510.213-2023
I/P-FG: 1500VAC, I/P-DA: 1500VAC, O/P-DA: 1500VAC
I/P-FG: 100M Ohms / 500VDC / 25°C / 70% RH
EN55015, EN61000-3-2, EN61000-3-3, GB 17625.1-2022, GB/T 17743-2021
EN61547, EN61000-4-2,3,4,5,6,8,11
191350H, MIL-HDBK-217F @ 230VAC full load
MTBF
and 25℃ ambient temperature
285x30x21mm (L*W*H)
Warranty
Tc=90°C
5 Years

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SRPL-2305N-100CC250-1000H and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sunricher SRPL-2305N-100CC250-1000H

  • Page 1 100W DALI DT6 NFC Enabled LED Driver(Constant Current) Short Circuit Yes, recovers automatically after fault condition is removed Over Current Protection Yes, recovers automatically after fault condition is removed Over Temperature Yes, recovers automatically after temperature drop Important: Read All Instructions Prior to Installation -25°C ~ +60°C Working Temp.
  • Page 2 Step 3: Unlock device, enter parameters configuring page. With NFC Programming devices Note Locked Unlock it 1) Do wiring according to the wiring diagram and power on the DALI system . 2) Recommend setting parameters without power-on the DALI devices . 2) Please make sure your mobile phone has NFC function and enable it .
  • Page 3 2.Enter CLO Setting homepage Step 5: After setting, please save the selected configuration via NFC and power on the device. Tips Enable CLO function Click “1",and set its time and level Set your desired time and levels. 1. NFC function doesn’t require any power driver. Graphic display 2.
  • Page 4 Wiring Diagram 4.Enter CD Setting homepage 1. With DALI bus 1) With single color LED luminaire ACN/ DALI DIMMABLE DRIVER ACL/ PUSH DIM DALI Bus 2. With PUSH dimmer N L G Enter CD mode Set your desired time and levels. Graphic display ACN/ DALI DIMMABLE DRIVER...
  • Page 5: Driver Performance

    With End Cap Driver Performance 313.6 Note: Test data under 350mA gear *: Due to its default current setting, the Max.load is 75W. It is not full-load in this case, we want to deliver 100% realistic data for your reference. 312.2 322.6 20%/ 32%/ 34%/ 38%/ 41%/ 46%/ 51%/ 56%/61%/67%/72%/76%...
  • Page 6: Expected Lifetime

    Expected Lifetime Output current 30 °C 40 °C 45 °C Module Number 60 °C 250 – 1000 mA SRPL-2305N-100CC250-1000H 42 °C 53 °C 60 °C 90 °C(max) SRPL-2309N-100CCT250-1000H 250 – 1000 mA Lifetime > 100,000 h > 100,000 h > 45,000 h >...

This manual is also suitable for:

Srpl-2309n-100cct250-1000h

Table of Contents