Related Manuals for VIA Technologies EBC-3610
Summary of Contents for VIA Technologies EBC-3610
- Page 1 Quick Installation Guide EBC-3610/3610L All-in-One VIA C3 667/733/800MHz Single Board with LCD, LVDS, AC97 Audio, & Dual 10/100Base-Tx Ethernet Ed. – 13 May 2002...
- Page 2 ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE. EBC-3610/3610L Quick Installation Guide...
- Page 3 Packing List Before you begin installing your single board, please make sure that the following materials have been shipped: 1 EBC-3610/3610L All-in-One VIA Eden Computing Module 1 Quick Installation Guide 1 Audio jacks and USB connector daughter board 1 CD-ROM contains the followings: —...
- Page 4 CPU card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static-shielded bag when they are not in the chassis. EBC-3610/3610L Quick Installation Guide...
- Page 5 Quick Installation Guide 2. Jumper & Connector Jumper & Connector Layout EBC-3610/3610L Quick Installation Guide 5...
- Page 6 3 x 1 header, pitch 2.0mm COM2 RS-232/422/485 select 3 x 2 header, pitch 2.0mm J5, J6 4 x 3 header, pitch 2.0mm (J6) AT / ATX power select 3 x 1 header, pitch 2.0mm ATATX1 EBC-3610/3610L Quick Installation Guide...
- Page 7 5 x 2 header, pitch 2.0mm USB1 CRT connector DB-15 female connector VGA1 LCD backlight brightness adjustment 3 x 1 header, pitch 2.54mm connector STN LCD contrast adjustment connector 3 x 1 header, pitch 2.54mm EBC-3610/3610L Quick Installation Guide 7...
- Page 8 Clear CMOS (J4) Clear CMOS Protect* * default 3.1.2 COM2 RS-232/422/485 Select (J5, J6) The EBC-3610 COM2 serial port can be selected as RS-232, RS-422, or RS-485 by setting J5 & J6. COM2 RS-232/422/485 Select (J5, J6) RS-232* RS-422 RS-485...
- Page 9 (and J1 to 2-3 closed), if ATX power supply is to be used. AT/ATX Power Select (ATATX1) AT P/S ATX P/S* ATATX1 * default Note: Set J1 to 2-3 closed, if AT power supply is to be used. EBC-3610/3610L Quick Installation Guide 9...
- Page 10 EBC-3610/3610L Connector Definitions 3.2.1 Secondary LCD Panel Connector (CN1) Signal Signal 3.3V 3.3V Vcon EBC-3610/3610L Quick Installation Guide...
- Page 11 Enable backlight signal. This signal is controlled as a part of the panel power sequencing ENVEE Enable VEE. Signal to control the panel power-on/off sequencing. A high level may turn on the VEE (LCD bias voltage) supply to the panel EBC-3610/3610L Quick Installation Guide 11...
- Page 12 LA20 IRQ12 IOW# B13 A13 SA18 LA21 IRQ11 SMEMR# B12 A12 SA19 LA22 IRQ10 SMEMW# LA23 IOCS16# B10 A10 IOCHRDY SBHE# MEMCS16# + 12 V OWS# - 12 V DRQ2 - 5 V IRQ9 RESETDRV IOCHCHK# EBC-3610/3610L Quick Installation Guide...
- Page 13 Quick Installation Guide 3.2.4 System Fan Connector (CN6) Signal 3.2.5 Audio Connector (CN7) Signal Signal Mic Bias Mic-In Line-In L Line-In R Line-Out L Line-Out R EBC-3610/3610L Quick Installation Guide 13...
- Page 14 EBC-3610/3610L 3.2.6 CD-ROM Audio Input Connector (CN8) Signal CD_R CD_GND CD_L CD_GND 3.2.7 IrDA Connector (CN9) Signal IRRX IRTX EBC-3610/3610L Quick Installation Guide...
- Page 15 Pin Header Serial Port 2 Connector in RS-232 Mode (CM1) Signal Signal 3.2.9 Pin Header Serial Port 2 Connector in RS-422 Mode (CM1) Signal Signal 3.2.10 Pin Header Serial Port 2 Connector in RS-485 Mode (CM1) Signal Signal DATA- DATA+ EBC-3610/3610L Quick Installation Guide 15...
- Page 16 EBC-3610/3610L 3.2.11 Serial Port 1 with External DB9 Connector (CM2) Signal Signal 3.2.12 Floppy Connector (FLP1) Signal Signal DSKCHG# SIDE1# RDATA# WPT# TRAK0# STEP# DIR# MOB# DSA# DSB# MOA# INDEX# DRVDEN1# DRVDEN0# EBC-3610/3610L Quick Installation Guide...
- Page 17 ENBKL +12V Note: For inverters with adjustable Backlight function, it is possible to control the LCD brightness through the VR signal (pin 4) controlled by VR1. Please see the VR1 section for detailed circuitry information. EBC-3610/3610L Quick Installation Guide 17...
- Page 18 EBC-3610/3610L 3.2.15 Auxiliary Power Connector (PWR1) Signal -12V 3.2.16 Power Connector (PWR2) Signal 3.2.17 USB Connector (USB1) Signal Signal VCC2 VCC1 EBC-3610/3610L Quick Installation Guide...
- Page 19 Quick Installation Guide 3.2.18 LCD Backlight Brightness Adjustment Connector (VR1) Signal CN5 pin 4 Variation Resistor (Recommended: 4.7KΩ, >1/16W) 3.2.19 STN LCD Contrast Adjustment Connector (VR2) Signal VCON EBC-3610/3610L Quick Installation Guide 19...
- Page 20 EBC-3610/3610L EBC-3610/3610L Quick Installation Guide...
Need help?
Do you have a question about the EBC-3610 and is the answer not in the manual?
Questions and answers