Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SIGLENT TECHNOLOGIES SDL1000X Series
Summary of Contents for SIGLENT TECHNOLOGIES SDL1000X Series
- Page 1 SDL1000X Programmable DC Electronic Load Quick Start EN01E...
-
Page 3: Copyright Information
Information in this publication replaces all previously corresponding material. Any method of copying, extracting, or translating the contents of this manual is not allowed without the permission of SIGLENT. Note: SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD. SDL1000X Quick Start... -
Page 4: Table Of Contents
Contents Copyright Information ......................1 General Safety Summary ...................... 3 Safety Terms and Symbols ....................4 Allgemeine Sicherheitsübersicht.................... 5 Sicherheitsbegriffe und symbole .................... 7 General Care and Cleaning ....................8 General Inspection ........................ 8 SDL1000X Brief Introduction ....................9 Panel Introduction ........................ 10 User Interface ........................ -
Page 5: General Safety Summary
General Safety Summary Carefully read the following safety precautions to avoid any personal injury or damage to the instrument and any products connected to it. To avoid potential hazards, please use the instrument as specified. Use the Proper Power Cord Only the power cord designed for the instrument and authorized by local government regulations should be used. -
Page 6: Safety Terms And Symbols
To avoid personal injury or damage to instrument, please do not operate in an explosive atmosphere. Keep surface of the product clean and dry To avoid dust or moisture in the air influence the performance of the instrument, please keep surface of the product clean and dry. -
Page 7: Allgemeine Sicherheitsübersicht
Allgemeine Sicherheitsübersicht Lesen Sie die folgenden Sicherheitshinweise sorgfältig durch, um Verletzungen oder Schäden am Gerät und an den daran angeschlossenen Produkten zu vermeiden. Um mögliche Gefahren zu vermeiden, verwenden Sie das Gerät bitte wie angegeben. Verwenden Sie ein geeignetes Netzkabel Verwenden Sie nur das fü... - Page 8 Betreiben Sie das Gerät nicht ohne Abdeckungen Betreiben Sie das Gerät nicht, wenn Abdeckungen oder Verkleidungen entfernt sind. Betreiben Sie das Gerät nicht bei vermuteten Defekten Wenn Sie vermuten, dass das Gerät beschä digt ist, lassen Sie es vor dem weiteren Betrieb von qualifiziertem Servicepersonal überprü...
-
Page 9: Sicherheitsbegriffe Und Symbole
Sicherheitsbegriffe und symbole Begriffe in diesem Handbuch. Diese Begriffe kö nnen in diesem Handbuch vorkommen: WARNUNG Warnhinweise weisen auf Bedingungen oder Praktiken hin, die zu Verletzungen oder zum Verlust des Lebens führen können. VORSICHT Vorsichtshinweise weisen auf Bedingungen oder Praktiken hin, die zu Schäden an diesem Produkt oder anderen Gegenstä... -
Page 10: General Care And Cleaning
General Care and Cleaning Care: Do not store or leave the instrument in direct sunshine for extended periods. To avoid damage to the instrument or probes, please do not expose them to fog, liquid, or solvents. Cleaning: Please perform the following steps to clean the instrument and probes. Disconnect the instrument from all power sources and then clean it with a soft damp cloth. -
Page 11: Sdl1000X Brief Introduction
SDL1020X-E comes with an input range of 150 V/30 A @ 200 W. The SDL1030X/ SDL1030X-E comes with an input range of 150 V/30 A @ 300 W. The SDL1000X series leads with measurement resolution of 0.1mV/0.1mA and the base SDL1000X-E series resolution is 1mV/1mA. Adjustable current slew rate range is 0.001 A/μs~2.5 A/μs, and it comes with built-in RS232/USB/LAN communication interfaces. -
Page 12: Panel Introduction
Panel Introduction Front Panel USB interface Knob Power Key Function button and power key Function Key Input Terminal The 3.5 inch TFT-LCD display is used to display system parameter settings, system output state, wave forms, menu options, prompt messages, etc. Knob When setting parameters, rotate the knob to increase or decrease the value of the digit at the cursor. - Page 13 Press the button to enter the constant power mode. Enter Utility mode by pressing the shift button at the same time. Press the button to enter the constant resistor mode. Enter LED mode by pressing the shift button at the same time. Press the button to enter Display mode.
- Page 14 Rear Panel Warning message RS232 interface AC input voltage description Analog current monitor output AC power socket 10. Analog voltage monitor output Fuse 11. FAN AC line power selection switch 12. Sense terminal, External control LAN interface terminal, PWM output terminal USB device Warning message Note reminding user to ground the instrument and that non-professional personnel should not...
- Page 15 LAN interface Use to connect to the local network by RJ45 interface. USB device Connects the instrument (as “slave” device) to external USB device (such as, USB storage device or external computer). RS232 interface Connect to the computer via 9-pin RS232 cable. Analog current monitor output User can observe the DUT output current level by connecting to an oscilloscope to monitor the current level.
- Page 16 Connect Power The SDL1000X load supports a variety of AC line power input values. For each line voltage, the rear panel voltage selector settings are to be set according to the table below: Table 1: AC input line power specifications AC Power Input Voltage selector configure 110 Vac ±...
-
Page 17: User Interface
User Interface Displays the load’s mode USB connection icon Displays the load’s state Keyboard lock Displays a Short state Setting value Remote sense mode Measured output values LAN connection icon 10. Voltage slew rate To Power on the instrument After the instrument is connected to the power source, press the Power key at the left bottom of the front panel to power on the instrument. - Page 18 Fuse Replacement The specifications of the fuse are relative to the actual input line voltage, shown in the table below. You can also refer to the rear panel “input power requirement” Input voltage Fuse specification 110 Vac T315 mA / 250V 220 Vac T315 mA / 250V To replace the fuse, please follow the steps below:...
-
Page 19: Troubleshooting
Troubleshooting The following are some common failures and their solutions. If the problem persists after following the listed steps, please contact SIGLENT. The instrument cannot power up. Check whether the power source is correctly connected. Check whether the power switch at the front panel is on. Remove the power cord and check whether the voltage selector is at the proper setting, whether the specification of the fuse is correct and whether the fuse is intact. - Page 20 Headquarters: SIGLENT Technologies Co., Ltd Add: Bldg No.4 & No.5, Antongda Industrial Zone, 3rd Liuxian Road, Bao'an District, Shenzhen, 518101, China Tel: + 86 755 3688 7876 Fax: + 86 755 3359 1582 Email: sales@siglent.com Website: int.siglent.com North America: SIGLENT Technologies America, Inc...
Need help?
Do you have a question about the SDL1000X Series and is the answer not in the manual?
Questions and answers