Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Martin Manuals
  4. Projector
  5. Exterior Projection Pro Compact
  6. User manual

Martin Exterior Projection Pro Compact User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Exterior Projection
Pro Compact
User Manual
with Safety and Installation Manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the Exterior Projection Pro Compact and is the answer not in the manual?

Questions and answers

Related Manuals for Martin Exterior Projection Pro Compact

Summary of Contents for Martin Exterior Projection Pro Compact

  • Page 1 Exterior Projection Pro Compact User Manual with Safety and Installation Manual...

  • Page 2: Dimensions

    Martin is a registered trademark of HARMAN PROFESSIONAL DENMARK ApS registered in the United States and/or other countries.

  • Page 3: Dimensions With Glare Shield Accessory

    Dimensions with glare shield accessory Ø13...

  • Page 4: Table Of Contents

    Zoom ......................9 Framing ...................... 9 Fixture setup ....................... 10 Setup using RDM ..................10 Setup using Martin Companion ..............10 Setting a DMX address ................10 Dimming curves ..................11 Parameter shortcuts ................. 11 Cooling fan speed ..................11 Hibernation mode ..................

  • Page 5: Introduction

    It will require time to warm up before normal operation is available. Precautions to avoid damage Important! To get the best out of the Exterior Projection Pro Compact and avoid causing damage that is not covered by the product warranty, make sure that everyone who is involved in installing, working on or using the fixture has read and understood this User Manual and the Safety and Installation Manual included at the end of this User Manual.

  • Page 6: Effects

    Slot 5: Color Temperature Correction 4000 K Slot 3: Blue It is possible to have custom color filters made, if required. Martin can supply an empty color wheel and filter specifications. Please consult your Martin supplier if you are interested. ®...

  • Page 7: Rotating Gobos

    Gobos are user-replaceable. You can replace them with custom gobos made to your own design provided that the gobos meet the quality and specifications of the Martin gobos supplied with the fixture. See the Service and Maintenance chapter at the end of this User Manual for details of installing and replacing gobos.

  • Page 8: Animation Wheel

    To compensate for these mechanical tolerances the fixture always indexes from a clockwise direction (as seen when looking at the projection). No matter how carefully we engineer and manufacture Martin products, all lighting fixtures are subject to mechanical tolerances. These will often cause very small changes in the indexing angles (i.e.

  • Page 9: Focus

    It is possible to have a custom animation wheel or a static gobo wheel produced by an optical component supplier and install this in place of the original Martin animation wheel. Martin can supply the necessary details and specifications to allow a supplier to produce a wheel to your own design.

  • Page 10: Fixture Setup

    Windows application that is available for download free of charge from www.martin.com. To program and manage fixtures, connect a Martin Companion hardware interface to the DMX link, then use a USB cable to connect a PC running the Martin Companion application to the Martin Companion hardware interface.

  • Page 11: Dimming Curves

    Dimming curves Available using RDM, Martin Companion and the Control / Settings DMX channel Four dimming curves are available: • Optically linear– The increase in light intensity appears to be linear as DMX value is increased. • Square law – (default setting) Light intensity control is finer at low levels and coarser at high levels.

  • Page 12: Hibernation Mode

    3. Activate the Drying out function. The fixture LEDs will light up, the heating plate will activate, the LED cooling fan will shut down and the three internal cooling fans will operate at full speed. Drying out will continue until you turn it off using Martin Companion, RDM or the Control / Settings DMX channel.

  • Page 13: Standalone Programming

    Standalone programming Available using Martin Companion In standalone mode, the Exterior Projection Pro Compact can display a ‘scene’ or a ‘show’ with no DMX control required. A scene consists of a combination of effects such as gobo selection, gobo movement, color, intensity, etc. A show is a sequence of scenes that runs automatically.
  • Page 14 It is possible to create different scenes in different fixtures if you select them separately (not all fixtures in a Standalone show have to show the same scenes). Martin Companion will automatically elect one fixture to become the Sync Host. Scene changes in all the Client fixtures will be synchronized with the Host.
  • Page 15 8. Click on RUN SHOW to set the fixtures to run their programmed Standalone show. Once you disconnect the cable between the PC running Martin Companion and the DMX/RDM link, the fixtures will run their Standalone show whenever they are powered on and not receiving a control signal.

  • Page 16: Managing The Fixture

    • Software version currently installed in the fixture. Returning to factory defaults You can return the fixture to its factory default settings, erasing any settings, stand-alone scenes, etc. stored in the fixture’s memory. ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 17: Rdm

    The Exterior Projection Pro Compact features RDM (Remote Device Management) capability. RDM lets you get information from the fixture and change settings in the fixture remotely over the DMX data link using an RDM-compatible DMX controller. Parameter IDs RDM commands are normally referred to as Parameter IDs or PIDs. The Exterior Projection Pro...
  • Page 18 0x8101 SYNCHRONIZED Normal operation / Sync host / Sync client Behavior when no DMX signal present: ✓ ✓ 0x81xx OFFLINE_MODE Standalone / Blackout / Full output / Last DMX state ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 19: Fixture Discovery

    1. Check that the fixtures are correctly connected to the RDM controller on the data link and that power is applied to all fixtures. 2. Send a discovery command via RDM (Martin Companion does this automatically as soon as the cable is connected).

  • Page 20: Operation

    The procedure for doing this is described in the Safety and Installation Manual included at the end of this User Manual. ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 21: Dmx Protocols

    Stop (wheel stops at current position) Rotating CCW slow → fast 217 - 239 Random Colors Stop (wheel stops at current full color) Random color slow → fast 241 - 255 ® Martin Exterior Projection Pro Compact User Manual, Rev. A...
  • Page 22 53248 – 55295 Slot 3 55296 – 57343 Slot 4 57344 – 59391 Slot 5 59392 – 61439 Slot 6 61440 – 63487 Slot 7 63488 – 65535 Slot 8 ® Martin Exterior Projection Pro Compact User Manual, Rev. A...
  • Page 23 Zoom 0 – 65535 Wide → narrow Fade 32768 Focus 0 – 65535 Infinity → near Fade 32768 DMX Control / Settings channel – see page 27 ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 24: Extended Mode

    Stop (wheel stops at current position) Rotating CCW slow → fast 217 - 239 Random Colors Stop (wheel stops at current full color) Random color slow → fast 241 - 255 ® Martin Exterior Projection Pro Compact User Manual, Rev. A...
  • Page 25 53248 – 55295 Slot 3 55296 – 57343 Slot 4 57344 – 59391 Slot 5 59392 – 61439 Slot 6 61440 – 63487 Slot 7 63488 – 65535 Slot 8 ® Martin Exterior Projection Pro Compact User Manual, Rev. A...
  • Page 26 Zoom 0 – 65535 Wide → narrow Fade 32768 Focus 0 – 65535 Infinity → near Fade 32768 DMX Control / Settings channel – see page 27 ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 27: Control / Settings Dmx Channel

    No function Drying out – stop drying out function and return to normal operation (1 sec.) No function Drying out – activate drying out function (1 sec.) 213-255 No function ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 28: Warning And Error Messages

    Warning and error messages The Exterior Projection Pro Compact monitors its own operation and is capable of self-diagnosis. If an operating parameter is exceeded or if an error occurs, the fixture stores a warning or error message that you can view with an RDM controller.

  • Page 29: Service And Maintenance

    Refer any service or repair operation not described in this manual to an authorized Martin service technician. Do not try to carry out such an operation yourself, as doing so may present a health or safety risk.
  • Page 30 • Replace a valve with a new item if it shows any signs of contamination or is not in perfect condition. • Replace valves after an extended period of use. Intervals for valve replacement depend on the installation environment. • Consult your Martin dealer about a suitable valve replacement schedule. • Contact Martin Service if a valve requires replacement ®...

  • Page 31: Updating Firmware

    Martin Companion Cable, available from Martin suppliers by ordering P/N 91616091. The Martin Companion application automatically downloads all currently available firmware versions for the Exterior Projection Pro Compact when you run the application on a PC that is connected to the Internet.

  • Page 32: Installing An Animation Wheel In The Animation Wheel Module

    (the center point is marked with an arrow on the module) and then tighten the thumbscrews. This will ensure that the aperture is aligned so that you can select the open position via DMX. ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 33: Replacing Gobos

    Gobos are exposed to severe thermal stresses, so custom gobos must meet the specifications and quality standards of the Martin gobos supplied with the fixture: Suitable material ........Borosilicate glass, coatings heat-resistant to 450°C (842° F) Alternative material ........
  • Page 34 It is important to install gobos facing in the correct direction. The orientations shown below are generally correct, but consult your Martin dealer or gobo supplier if you are in any doubt about the orientation of a specific gobo type.
  • Page 35 The key fits into a keyway in the goboholder and prevents the gobo from moving in the goboholder and losing its correct orientation over time. You can order gobo mounting rings in sets of 10 rings as an accessory from your Martin supplier. Ask for P/N MAR-90560270.

  • Page 36: Replacing A Rotating Gobo

    Replacing a rotating gobo Rotating gobos in the Exterior Projection Pro Compact are installed in goboholders in the gobo modules. To replace a gobo: 1. Remove the effects compartment cover as described in the Safety and Installation Manual included at the end of this User Manual. If a gobo module is already installed in the fixture, remove it, using the Safety and Installation Manual as a guide and place the module on a clean, flat work surface with the goboholder teeth facing upwards.

  • Page 37: Gobo Care

    • Clean the coated side of gobos with dust-free and oil-free compressed air only. • Clean the uncoated side of gobos with photographic quality lens-cleaner and optics cleaning tissues. Use a repeated dabbing action rather than a rubbing action. ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 38: Calibrating The Fixture

    5. When you have finished adjusting calibration offsets, send value 0 on the Control/Settings channel and hold for 5 seconds to exit the DMX calibration procedure and return to normal DMX control. ® Martin Exterior Projection Pro Compact User Manual, Rev. A...

  • Page 39: Troubleshooting

    For perfect standalone show synchronization, operation different fixtures do not check that all fixtures have the same number contain the same number of scenes in their standalone shows. of scenes ® Martin Exterior Projection Pro Compact User Manual, Rev. A...
  • Page 40 www.martin.com...
  • Page 41 Exterior Projection Pro Compact Safety and Installation Manual...
  • Page 42 Martin is a registered trademark of HARMAN PROFESSIONAL DENMARK ApS registered in the United States and/or other countries.
  • Page 43 Table of contents Dimensions ......................2 Safety information ....................4 Introduction ......................11 Before using the product for the first time ..........11 Precautions to avoid damage ..............11 Fixture overview ....................12 Physical installation .................... 13 Protection from the sun ................13 Cooling .....................

  • Page 44: Safety Information

    User Manual must be referred to an authorized Martin service agent. The light source contained in the fixture may be replaced by Martin or an authorized Martin service agent only.
  • Page 45 The latest version of this manual is available for download from the Exterior Projection Compact Pro pages of www.martin.com. Before you install, operate or service an Exterior Projection Pro Compact fixture, check the Martin website and make sure that you have the latest user documentation for the fixture. Document revisions are indicated at the bottom of page 2.
  • Page 46 The fixture is supplied without power and data cables. To connect the fixture to mains power you must use either a PD hybrid (power and data) cable available from Martin for the fixture, or separate power cable that is minimum 16 AWG or 1.5 mm and rated minimum 11 A.
  • Page 47 Do not modify the fixture in any way not described in this manual or install other than genuine Martin parts. Do not stick filters, masks or other materials onto any lens or other optical component. Use only accessories approved by Martin to modify the light beam.
  • Page 48 Do not attempt to use a fixture that is obviously damaged. Do not modify the fixture or install other than genuine Martin parts. The fixture has an Effective Projected Area (EPA) of 0.1 m Exterior Projection Pro Compact Safety and Installation Manual...
  • Page 49 El peso del dispositivo varía según la configuración, pero pesa un máximo de 14,1 kg, incluido el yugo de montaje y con un máximo de accesorios (protector antideslumbrante, módulo de encuadre, rueda de 4 gobos y rueda de animación) instalados. Exterior Projection Pro Compact Safety and Installation Manual...
  • Page 50 No intente utilizar un aparato que presente daños visibles. No modifique el dispositivo ni instale piezas que no sean originales de Martin. El accesorio tiene un Área Proyectada Efectiva (Effective Projected Area, EPA) de...

  • Page 51: Introduction

    The Exterior Projection Pro Compact can also function without DMX control as a stand-alone projector and run a show with up to twenty dynamic lighting effects that you can program using the free Martin Companion fixture management Windows software suite.

  • Page 52: Fixture Overview

    G – Pressure relief valve C – Effects compartment cover (service H – Cable gland for DMX/RDM data lid) input cable or PD cable D – Glare shield (optional accessory) E – Cooling vent Exterior Projection Pro Compact Safety and Installation Manual...

  • Page 53: Physical Installation

    Cooling The Exterior Projection Pro Compact has a thermal protection system. If temperatures inside the fixture exceed safe levels, it regulates LED output to protect components. The fixture has internal forced air cooling and an external IP-rated cooling fan. Ensure sufficient ventilation and free airflow around the fixture, especially around the grill on the back of the fixture, to minimize any reduction in LED output due to high temperatures.
  • Page 54 Once pan is correct, fasten two 12 mm (1/2 inch) shaft diameter bolts to the surface with one bolt passing through each of the holes B. Once bolts have been installed in holes B, pan adjustment is no longer possible. Mounting yoke base Exterior Projection Pro Compact Safety and Installation Manual...

  • Page 55: Adjusting Aiming (Pan And Tilt)

    Safety Cable Attachment Bracket accessory from Martin by ordering P/N MAR-90590050 and install it on the fixture, then install a safety cable that is approved for the weight of the fixture using the bracket: 1.

  • Page 56: Magnetic Switch For Testing And Status

    Swipe 5 or cycle power off/on to exit the status/test sequence. If the fixture is not connected to DMX when you begin swiping but you connect it to DMX while swiping is active, the fixture immediately starts normal DMX operation. Exterior Projection Pro Compact Safety and Installation Manual...

  • Page 57: Connecting To Power And Data

    Do not try to connect the fixture to a three-phase, three-wire (three phases, no Neutral) system. There is no power on/off switch. Power is applied to an Exterior Projection Pro Compact fixture as soon as it is connected to power. Provide a means to disconnect or shut down power to fixtures that is easily accessible and is located close to the fixtures.

  • Page 58: Installation Layout Options

    PD cable connectors PD cable Hybrid link PD cable tails that are suitable for the Exterior Projection Pro Compact are available from Martin as accessories: • PD Cable Tails Set, 0.5 m, Black, EU, P/N MAR-91700020 • PD Cable Tails Set, 0.5 m, White, EU, P/N MAR-91700022 Each set consists of 1 x IN and 1 x THRU cable tail with PD connectors installed on one end of each cable.

  • Page 59: Connecting Via Separate Power And Data Cables

    Martin can also supply loose PD connectors and lengths of PD cable. For instructions on connecting fixtures in this configuration, see ‘Connecting via PD-type hybrid cables’ on page 21. Connecting via separate power and data cables Connecting to power To connect the fixture to AC mains power you must use correctly dimensioned cable that is suitable for the installation environment (with regard to UV resistance, weatherproofing, temperature rating etc.)
  • Page 60 A DMX512 data link is required in order to control the fixture via DMX and manage fixtures via RDM. If you need advice or assistance in planning the link, your Martin supplier will be happy to help. To connect the fixture to control data you must use DMX512-compatible data cable that is suitable for the installation environment (with regard to UV resistance, weatherproofing, temperature rating etc.)

  • Page 61: Connecting Via Pd-Type Hybrid Cables

    You can connect the fixture to power and data using the PD cable accessories available from Martin (consult your Martin supplier or see the Exterior Projection Pro Compact area of the Martin website for ordering details). PD cable tails are supplied with a PD connector at one end and bare ends at the other end.
  • Page 62 Check that all installation work is completed and carry out appropriate tests and safety checks before applying power. Exterior Projection Pro Compact Safety and Installation Manual...
  • Page 63 The fixture with two PD cable tails installed should look as shown in the photo on the right. Exterior Projection Pro Compact Safety and Installation Manual...

  • Page 64: Service And Maintenance

    Refer any service or repair operation not described in this manual to an authorized Martin service technician. Do not try to carry out such an operation yourself, as doing so may present a health or safety risk.
  • Page 65 • Do not use liquid gasket or any other type of sealant on sealing surfaces or seals. Exterior Projection Pro Compact Safety and Installation Manual...
  • Page 66 Installing a glare shield accessory To install the glare shield that is available as an optional accessory from Martin, see photo on right. Hold the glare shield up to the front of the fixture and fasten it in position using the four supplied screws.
  • Page 67 B first; install the animation wheel A second. • Remove the animation wheel A first; remove the gobo module B second. • No special installation and disassembly order is necessary for the framing module. Exterior Projection Pro Compact Safety and Installation Manual...
  • Page 68 2. When the module is correctly located in the head, fasten it into position with its two Allen (hex) head mounting screws. Use a torque driver to tighten the screws to a torque of 2 Nm. Installing an animation wheel module Exterior Projection Pro Compact Safety and Installation Manual...
  • Page 69 • The two red thumbwheels adjust the angle and insertion of the left-hand blade in the projection. • The two gold thumbwheels adjust the angle and insertion of the right-hand blade in the projection. Exterior Projection Pro Compact Safety and Installation Manual...

  • Page 70: Specifications And Compliance

    Specifications and compliance For product specifications, please see the Exterior Projection Pro Compact area of www.martin.com. FCC compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 71 www.martin.com...