Sioux Tools 5560 Operator Instructions

Operator Instructions
Includes
-
Foreseen Use,
Work
Stations, Putting Into Service,
Operating, Dismantling, Assembly and Safety Rules.
Manufacturertsupplier
Sioux
Tools
Inc.
2901 Floyd
Boulevard
P.O. Box 507
Sloux
Clty, IA 51 102
U.S.A.
Tel No. 71 2-252-0525 Fax No. 71 2-252-4267
Product
Net Weight
Recommended Use
Oi
6.8
Ibs
Balancer Or
Support
3.1 Kg N O
Air Pressure
Recommended Working 6.2 bar 90 PSI
Maximum 6.2
bar
90 PSI
SAFETY MESSAGES
1
A
Paisonal safety Equipment
Always Read Instructions
Use
-
Safety G ~ E I S S ~ S YES
1
0
Before
Using W i T o o t e
use
-
Safety Gloves
@
2zwsahw
Use
-
Safety
Boots
@
Wsar Hearing Protacttoi
Use
-
Breathing
Masks
void Prolonged -sure
use-
m
pmtmors YES
A
Towbmh
Safety rules when using a 5560 Sander
-
Do not use as
a grinder.
-
Do not use polystyrene pads.
-
Use accessories rated above 10,000 RPM.
-
Prolonged exposure to vibration may cause injury.
-Read all Instructions before using this tool. All
operators must be fully trained in its use and aware of
these safety rules.
-Do not exceed the maximum working air pressure.
-
Use personal protection equipment as recommended.
-Use compressed air only at the recommended
condi lions.
- I f the too! appears to malfunction, remove from use
immediately and arrange for service and repair. If it is
not practical to remove tool from service, then shut off
the air supply to the toot and wrie or
have written a warning note and 1 -
Form
# Z422
Important
Read these instructions carefully before installing, operating,
eervlclng
or
repalring
this
tool.
Keep
these Instructions
In
a safe
access1 ble place.
Product
Type
RPM
2,500
Stralght Line
Air
Sander
cF,esper
Mi,,,
I
I
Model No/Nos
Serial
No,
Recommended Hose
Bore
Recommended Max.
Size
-
Minimum
Hose Length
5/16
Ins
8MtM 30 Ft 10
M
Noise Leve!: Sound Pressure Level 87.0 dB(A)
Sound Power Level 98.0 dB(A)
Test
Method:
Tested in accordance with Pneurop
test code PN8NTC1
and
IS0 Standard 3744
Vibration Level
14.9 Meters
/ Sec2
Test Method:
Tested
In
accordance
with I S 0
standards 8662 Parts 1 & 8
Tested at 90
PS!G Air
Pressure
-Always when using the tool, adopt a firm footing andlor
position and grip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.
-Use only correct spare parts for maintenance
and
repair. Do not improvise or make temporary repairs.
Major servicing and repairs should only be carried out
by persons trained to do so.
-
Do not lock, tape,
wire, etc. the 'Ob/Off' valve
in
'On'
position. The throttle lever, etc. must always be free to
return to the ' O f f ' position when released.
-Always shut o f f the air supply to
the
tool
and
press the
'OnIOff' valve to exhaust the air from the feed hose
before fitting, removing or adjusting
the
working
attachment fitted to the tool.
attach it to the tool.
Au Pipe And Fittings -
H tool is to be used with
a balancer O r
Should Be 1/2- or
tar*
other suspension device, ensure that
the tool is firmiy attached to the
wilh sufficient Capacity
suspension/support device.
To Maintain
Recommended
Wortdng Pressure At
-When operating the tool, always keep
the
body
and particularly the hands
away from the working attachment
fixed to the tool.
-The tool is not electrically insulated.
Never use the tool i f there is any
chance of r n i f l g
ifitÂ
contact with live
Recommended Air Supply System
electricity. Figure 1
Page No 1