Product Description Drone Forward Motor Tilt Motor Camera (Correspond to Propeller A) (Correspond to Propeller B) Power Switch Propeller A Propeller B Propeller B Battery Propeller A Tips: The aircraft has two types of propellers (“A” and “B”) marked A and B. Please match the Mark “A”...
Remote Control Calibrate Power Right Left Joystick Joystick One-button Takeoff / Landing WASD Fine- Speed tuning Switch Emergency Stop Headless Mode 360° Rotation Light On / Off Short press Rotation / to take photo Long press 1s to Orbit Flight record video/photo Tips: For photos / videos taken with the remote control, you need to connect to the app first and...
Page 5
Mobile Phone Holder Installation Insert the mobile phone holder into the upper holder slot of the remote control as shown in the picture. Battery Installation of Remote control Open the battery cover of remote control and install 3 AAA batteries (not included in the packaging) as shown in picture below: Tips: 1.
Page 6
Battery Battery Installation and Charging 1. Place the battery in the drone and buckle it as shown in picture below: 2. Recharge the battery as shown in picture below: USB charger indicator turns red during charging. Once charging is done, the charger indicator turns off. Note: 1.
Download FLYCAM For smartphones with Android 5.0+. Search and download "FLYCAM" on Google Play, or scan the QR code below. For smartphones with iOS 9.0+. Search and download "FLYCAM" on the App Store, or scan the QR code below. FLYCAM APP Connect to your phone A23W can be controlled directly from your smartphone as follows: 1.
Intelligent Flight Mode Speed Adjustment Head-on Mode Horizontal Calibration Virtual Joystick Gravity-sensing Mode Trajectory Flight A23W drone has two remote control modes, mode 1 and mode 2. Mode 1 is set by default. Quick Start Frequency Match 1. Long press the power button on upper cover to turn on the drone and indicator flashes;...
Calibration Press “ ” (calibrate button) to start calibration. The indicator light flashes rapidly during calibration and after the calibration is completed, the indicator light is always on. When drone falls, please calibrate it again (place the drone on horizontal ground during calibration). Takeoff and Landing Method 1 As shown in picture below, press “...
Method 2 As shown in picture below, push both joysticks simultaneously to unlock the drone, then push the left one upwards to take off (after the drone takes off, push the right one downwards to land). Unlock Takeoff / Landing Emergency Stop In case of emergency, press and hold the "STOP"...
Front / Rear, Left / Right Use “right joystick” to control the left / right direction during flight. Headless Mode The drone flies at a fixed direction and does not change with the direction of the drone, as shown in picture below: Front Front Left...
Fine-tuning If the drone is tilted to certain direction, instead of a stable state, press the fine-tuning button after takeoff to the opposite flight direction to reach the stable state. Aerobatic Flight 3D Rotation Step 1: Press “ ” (rotate button) to enter the rotation mode and the remote control beeps continuously.
Rotation Mode As shown in picture below, shot press “ ” (rotation button) to enable / disable the rotation mode, and the remote control makes a "beep" sound. In this mode, the drone rotates at a fixed speed. Orbit Flight Mode As shown in picture below, long press 1s “...
Throw Mode The drone can take off automatically after being thrown manually. Please connect the drone to the remote control and calibrate it, then hold the drone in your hand and toss it into the air. As shown in picture below: Safety Low Battery Alarm When voltage is lower than 3.5V, the indicator of the drone flashes...
Page 15
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 16
A23-W Name Model Shenzhen Deepsea Excellence Technology Co., Ltd. Manufacturer 5th Floor, Building 7, Hongfa High-tech Park, Keji Address 4th Road, Shiyan Street, Baoan District, Shenzhen Battery Information 3.85V 380mAh Charging voltage/current FCC ID 2AYUO-A21 EC REP: E-CrossStu GmbH. Mainzer Landstr.69,60329 Frankfurt am Main UK REP: DST Co., Ltd.
Need help?
Do you have a question about the A23-W and is the answer not in the manual?
Questions and answers