Related Manuals for Warming Trends MATCH LIT CFB60 NG/LP as match lit
Summary of Contents for Warming Trends MATCH LIT CFB60 NG/LP as match lit
- Page 1 OWNER’S GUIDE AND INSTRUCTION MANUAL THANK YOU FOR YOUR PURCHASE! SCAN TO VISIT SCAN TO SEE AN UPDATED PATENTED WARMING-TRENDS.COM ICC-ES LIST www.warming-trends.com/patents Version 4.7...
-
Page 2: Important Product Warnings
IMPORTANT PRODUCT WARNINGS DANGER FIRE OR EXPLOSION HAZARD If you smell gas: • Shut off gas to the appliance. • Extinguish any open fl ame. • If odor continues, leave the area immediately. • After leaving the area, call your gas supplier or fi re department. •... -
Page 3: Avertissements Importants Concernant Les Produits
AVERTISSEMENTS IMPORTANTS CONCERNANT LES PRODUITS DANGER RISQUE D’INCENDIE OU D’EXPLOSION S’il y a une odeur de gaz: • Coupez l’admission de gaz de l’arrareil. • Éteindre toute fl amme nue. • Si l’odeur persiste, éloignez-vous de l’appareil et appelez immédiatement le fournisseur de gaz ou le service d’incendie. -
Page 4: Table Of Contents
TABLE OF CONTENTS Important Product Warnings............................... Avertissements Importants Concernant les Produits....................... Certified Units....................................General Information..................................Code Requirements..................................Minimum and Maximum Gas Inlet Pressures..........................Location Considerations................................Construction of Enclosure................................Fire Feature Clearance Diagram..............................Critical Dimensions - Construction & 24V Electronic Ignitions....................General Installation Instructions.............................. -
Page 5: Certified Units
CERTIFIED BURNER SYSTEM UNITS Compliance with the following codes: Compliance with the following standards: 1. 2021, 2018, 2015, 2012, and 2009 International Fire Code® (IFC) 1. ANSI Z21.97/CSA 2.41-2017 Outdoor Decorative 2. 2021, 2018, 2015, 2012, and 2009 International Fuel Gas Code® (IFGC) Gas Appliances 3. -
Page 6: General Information
Warming Trends is not responsible for damage due to improperly installed or operated units. Installers must leave this user guide with the end user. Instructions are updated as needed, and it is the installer or owners’ responsibility to periodically review Warming Trends website for applicable updates (www.Warming-Trends.com.) Please keep this with... -
Page 7: Code Requirements
C O D E R E Q U I R E M E N T S It is the responsibility of the installer to consult with the local municipality and to FOLLOW ALL LOCAL CODES concerning the installation and operation of the fire feature. For systems with Mercury Ignition Systems: When the appliance is for connection to a fixed piping system, the installation must conform with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1·NFPA54;... -
Page 8: Location Considerations
30” and for rectangular plates or pans over 40”. Warming Trends Burners, Ignitions, Media, and other Accessories may be installed in Outdoor Fire Places. The clearances, materials, venting, and construction standards for Outdoor Fire Places may be determined by Local or National Codes. -
Page 9: Construction Of Enclosure
Building capstone inner ledge over outer edge of plates or pans will impede access to system and result in the need to crack or remove capstones to gain access. Warming Trends is not responsible for damage to enclosure for any reason whatsoever. -
Page 10: Fire Feature Clearance Diagram
F I R E F E AT U R E C L E A R A N C E D I A G R A M Vertical clearance of 120” from burner to combustible structure or materials is required. Horizontal or lateral clearance of 36” between edge of burner and combustible structure or materials is required. -
Page 11: Fire Feature Clearances Diagram
F I R E F E AT U R E C L E A R A N C E D I A G R A M - M E R C U R Y I G N I T I O N S Y S T E M Vertical clearance of 120”... -
Page 12: Critical Dimensions - Construction & 24V Electronic Ignitions
C R I T I C A L D I M E N S I O N S - C O N S T R U C T I O N & 2 4 V E L E C T R O N I C I G N I T I O N S (303) 346 - 2224 | Orders@Warming-Trends.com... -
Page 13: General Installation Instructions
Never use tools. If the key valve will not turn by the fire feature. See Clearance Diagrams starting hand, don’t try to repair it. Force or attempted repair on page 10 for placement. Warming Trends® is not may cause a fire or explosion. responsible for any damages to the capstone. -
Page 14: Liquid Propane Guidelines
L I Q U I D P R O PA N E G U I D E L I N E S For safe operation of LP appliances, it is important to use LP cylinders that meet the following criteria: •... -
Page 15: Connection Diagrams Match Lit Ignition System
LEAVE THIS CONNECTION DIAGRAM WITH END USER. M AT C H L I T S Y S T E M : C O N N E C T I O N D I A G R A M S 249K BTU SYSTEMS AND BELOW 1. - Page 16 M AT C H L I T: 2 4 9 K B T U S Y S T E M S A N D B E L O W - C O N T I N U E D 4. CONNECT WHISTLE-FREE FLEX LINE (FK1) Connect the Whistle-Free Flex Line to the Flared Fitting previously attached to the coupling on the Coupling...
- Page 17 M AT C H L I T: C O N N E C T I O N D I A G R A M S 250K - 300K+ BTU SYSTEMS 1. LOCATE FK2 Parts include two Whistle-Free Flex Lines, Key Valve, Escutcheon Plate, and Keys.
- Page 18 M AT C H L I T: I N S TA L L AT I O N 2 5 0 K - 3 0 0 K + B T U - C O N T I N U E D 4.
-
Page 19: Volt Ignition System
2 4 V O LT: C O N N E C T I O N D I A G R A M S 1. LOCATE FK1 Parts include Whistle-Free Flex Line, Key Valve, Escutcheon Plate, and Keys. STEP 1 - FIT180 3”... -
Page 20: Connect Electricity
2 4 V O LT: I N S TA L L AT I O N U P T O 2 4 9 K B T U S Y S T E M S - C O N T I N U E D STEP 5 4. - Page 21 2 4 V O LT: C O N N E C T I O N D I A G R A M S 250K - 300K+ BTU SYSTEMS 1. LOCATE FK2 Parts include two Whistle-Free Flex Lines, Key Valve, Escutcheon Plate, and Keys.
- Page 22 2 4 V O LT 2 5 0 K - 3 0 0 K + B T U S Y S T E M S : I N S TA L L AT I O N C O N T I N U E D 4.
- Page 23 2 4 V O LT 2 5 0 K - 3 0 0 K + B T U S Y S T E M S : I N S TA L L AT I O N - C O N T I N U E D 6.
-
Page 24: Push Button Ignition System
P U S H B U T T O N I G N I T I O N S Y S T E M C O N N E C T I O N D I A G R A M S - U P T O 3 0 0 K B T U S Y S T E M S 1. -
Page 25: Mercury Ignition System
INSTALLATION OF THE MERCURY IGNITION PILOT ASSEMBLY TO THE PLATE USING PRE CUT KNOCKOUTS The Warming Trends plate/pan that was included with your Order should have pre-cut pilot assembly knockouts for vari- ous burners. The burner type and size are etched into the plate/pan next to the knockout for that burner’s pilot assembly location. - Page 26 M E R C U R Y I G N I T I O N S Y S T E M : I N S TA L L AT I O N C O N T I N U E D 2.4 Rotate the Pilot Assembly in the knockout opening until the circular opening on the Pilot Hood and Thermocouple are adjacent to the nearest jet with the Thermocouple nearest to the jet.
- Page 27 4. CONNECTING THE FLEX LINE TO THE VALVE ASSEMBLY Please Note: Warming Trends sells two Flex Line Kits for the Mercury Ignition System, depending on the BTU supply of the burner. The FKM1 has one (1) fl ex line and fi ts burners up to 249K BTUs {See Photo 6}. The FKM2 has two (2) fl ex lines and fi ts burners 250K BTUs or more {See Photo 7}.
- Page 28 M E R C U R Y I G N I T I O N S Y S T E M : I N S TA L L AT I O N C O N T I N U E D 4.2 The Flex Line is provided with a male fl are hose adapter loosely attached.
- Page 29 M E R C U R Y I G N I T I O N S Y S T E M : I N S TA L L AT I O N C O N T I N U E D FKM2 INSTRUCTIONS: 4.5 Identify the “outlet”...
- Page 30 M E R C U R Y I G N I T I O N S Y S T E M : I N S TA L L AT I O N C O N T I N U E D 4.7 Apply joint compound, thread sealant, or plumbing tape to the ¾’’...
- Page 31 M E R C U R Y I G N I T I O N S Y S T E M : I N S TA L L AT I O N C O N T I N U E D 5.2 The pilot tube connects directly above the thermocouple.
- Page 32 M E R C U R Y I G N I T I O N S Y S T E M : I N S TA L L AT I O N C O N T I N U E D 6.
- Page 33 M E R C U R Y I G N I T I O N S Y S T E M : I N S TA L L AT I O N C O N T I N U E D 6.4 WITHOUT ANY THREAD SEALANT take the other end of the fl ex line attached to the valve assembly from Step 4 and attach the female fl ared end to the male fl ared end that is attached to the plate from Step 6.3.
- Page 34 M E R C U R Y I G N I T I O N S Y S T E M : I N S TA L L AT I O N C O N T I N U E D 6.9 WITHOUT ANY THREAD SEALANT, take the female flared ends of the flex lines attached to the valve assembly from Step 4 and attach to the male flared end of each of the flared fittings extending from the ¾”...
-
Page 35: Warning Label
W A R N I N G L A B E L The following label has been provided with the appliance. Affix the label in a conspicuous location adjacent to the appliance. WARNING: Improper installation, adjustment AVERTISSEMENT: Une installation, un alteration, service, or maintenance can cause ajustement, une modification, une réparation property damage, personal injury, or loss of life. -
Page 36: Lighting Instructions Match Lit Ignition
O P E R AT I N G I N S T R U C T I O N S Keep the area clear and free from combustible materials, gasoline, and other flammable vapors and liquids. Solid fuels shall not be burned in the fire feature. Leaves, sticks, wood, paper, clothing, food material, etc. should be kept away from the fire feature. -
Page 37: Lighting Instructions
L I G H T I N G I N S T R U C T I O N S : M E R C U R Y I G N I T I O N S Y S T E M ™ C O N T I N U E S REPLACING THE BATTERY If your Push Button Ignition System is not lighting, you may need to replace the battery. -
Page 38: Firestorm Owner Information And Installation
F I R E S T O R M S T E E L G A S L O G O W N E R I N F O R M AT I O N A N D I N S TA L L AT I O N Thank you for your purchase of a FireStorm® Steel Gas Log from Warming Trends. We appreciate your business and hope that... -
Page 39: Semi-Annually
G E N E R A L M A I N T E N A N C E CLEANING STEEL LOG Soot may build up along the openings in the log or on its surface in general. Annual cleaning is recommended. However, if soot restricts or reduces normal flame performance, clean openings immediately. -
Page 40: Warranty
1) make it do so or 2) replace it with one that is at least functionally equivalent, you may return it to Warming Trends and your money will be refunded. The warranty stated above will not apply to the extent that there has been misuse or use contrary to specifications or the appropriate user or operating manual, installation defect, accident, modification, unsuitable physical or operating environment, operation in other than the specified operating environment (e.g., outdoor... -
Page 41: Disclaimer Of Additional Warranties
Manual or as otherwise approved by Warming Trends, in writing, prior to sale. In the event a Mercury Ignition system must be replaced due to a defect or malfunction of the system, Warming Trends will repair or replace the system at no cost for the first year. -
Page 42: Return Policy
R E T U R N P O L I C Y RETURNS We hope that you truly enjoy your Warming Trends purchase. If you are not satisfied, we accept product returns for thirty (30) days of date of purchase, subject to the conditions below. -
Page 43: California Residents: Prop 65 Warning
Replacement Parts, Questions, or Need Assistance? Our team is happy to help. Call our Flame Specialists at (303) 346-2224 or email us at Orders@Warming-Trends.com. For more information about Warming Trends products, please visit us at www.Warming-Trends.com. SCAN QR CODE FOR AVAILABLE RESOURCES ON WARMING-TRENDS.COM... -
Page 44: Congratulations On Your Purchase
CONGRATULATIONS ON YOUR PURCHASE! We appreciate your business and look forward to seeing your fi nished project. Tag us on Instagram! @WarmingTrends SCAN TO VIEW OUR INSTAGRAM (303) 346 - 2224 | Orders@Warming-Trends.com...
Need help?
Do you have a question about the MATCH LIT CFB60 NG/LP as match lit and is the answer not in the manual?
Questions and answers