Greenlee 1813 Operation, Service And Parts Instruction Manual
  1. Manuals
  2. Brands
  3. Greenlee Manuals
  4. Industrial Equipment
  5. 1813
  6. Operation, service and parts instruction manual
Greenlee 1813 Operation, Service And Parts Instruction Manual

Greenlee 1813 Operation, Service And Parts Instruction Manual

Bending table for 881 hydraulic bender
Hide thumbs Also See for 1813:
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION, SERVICE AND PARTS
INSTRUCTION MANUAL
1813 BENDING TABLE
FOR 881 HYDRAULIC BENDER
Read and understand this material before operating or
servicing this bender. Failure to understand how to
safely operate this bender could result in an accident
causing serious injury or death. This tool should only
be operated by qualified personnel.
999 6389.2
© 1996 Greenlee Textron Inc.
IM 955 REV 8 8/96
https://manual-hub.com/

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1813 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Greenlee 1813

Summary of Contents for Greenlee 1813

  • Page 1 Failure to understand how to safely operate this bender could result in an accident causing serious injury or death. This tool should only be operated by qualified personnel. 999 6389.2 © 1996 Greenlee Textron Inc. IM 955 REV 8 8/96 https://manual-hub.com/...

  • Page 2: Table Of Contents

    Parts List ....................... 9 Introduction The Greenlee No. 1813 Bending Table is designed to make your Greenlee No. 881 Hydraulic Bender easier to use. Loading is faster and easier. The vertical, bench-high bending means greater control and freedom of movement for the operator and less fatigue, too.
  • Page 3 • Operate power equipment in uncluttered areas providing good footing and support. • Keep others a safe distance from the work area. • Use only original equipment or Greenlee specified replacement parts and accessories. Failure to observe these warnings could result in severe injury or death.

  • Page 4: Setup

    1. Refer to Bulletin IM-881 to assembly the 881 ram required for the table bed. These are not connecting bars and roller with the proper pins and furnished with the No. 1813 Bending Table. spring clips. 1. Insert each of the four legs (7) into the sockets of the 2.

  • Page 5: Adjusting Ram Position

    4" conduit. the yoke. Then attach the ram positioner to the yoke with the yoke pin as shown in Fig. 2. Figure 1 Figure 2 Greenlee Textron Inc. / Subsidiary of Textron Inc. 4455 Boeing Dr., Rockford, IL 61109-2988 815/379-7070 https://manual-hub.com/...
  • Page 6 1813 Bending Table Figure 4 Figure 3 Figure 5 Figure 6 4455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070 Greenlee Textron Inc. / Subsidiary of Textron Inc. https://manual-hub.com/...

  • Page 7: Bending

    Note: Pipe vise assembly is designed to allow only a 1 ° maximum variation between bends of various 3. Attach the Greenlee No. 1805 Bending Degree conduit sizes from 2-1/2 to 4". Protractor (11) to the portion of the conduit project- ing in front of the saddle.

  • Page 8: Exploded View

    1813 Bending Table 1813 Bending Table 4455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070 Greenlee Textron Inc. / Subsidiary of Textron Inc. https://manual-hub.com/...

  • Page 9: Parts List

    Carriage Unit ..................1 905 1788.1 Screw, Shoulder .750" x 2.75" x 5/8–11 ..........6 502 4720.4 Roller .767" x 2.50" x 2.12" 2" Pipe (1813) ........2 502 1351.2 Spacer .824" x 1.05" x .38" ..............2 905 0507.7 Washer, Lock .516"...
  • Page 10 GREENLEE Greenlee Textron Inc. / Subsidiary of Textron Inc. 4455 Boeing Drive, Rockford, IL 61109-2988 USA General Offices: 815/397-7070 Customer Center and Field Service: 800/435-0786 Fax (24 Hour) Customer Center: 800/451-2632 • 815/397-1865 Canada Fax (24 Hour) Customer Center: 800/524-2853 Printed in U.S.A.

Table of Contents