Related Manuals for Euro Appliances ECT900GX2
Summary of Contents for Euro Appliances ECT900GX2
- Page 1 USAGE AND CARE GUIDE PRODUCT CODE: ECT600GS ECT60WCX ECT60GX ECT900GX ECT900GX2...
- Page 2 This manual explains the proper installation and use of your appliance, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference. In case of failure, only the Authorized Technical Service may repair this hob.
-
Page 3: Safety Instructions
Children’s Safety ⚫ The cooking zones will become hot when you cook. Therefore, always keep small children away from the appliance. ⚫ The appliance is not intended for use by young children or infirm persons without supervision. ⚫ Young children should be supervised to ensure that they do not play with the appliance. Safety During Use ⚫... - Page 4 AS/NZS 3000 – Electrical Installations (Wiring Rules) Building codes Any other relevant statutory regulations. ⚫ Check the gas type label on the underside of the hotplate, adjacent to the gas connection to ensure it corresponds to the installation gas supply. If in doubt contact the supply authority.
-
Page 5: Product Description
Front LPG: 45mm 30.5MJ/h 29.5MJ/h ECT60GX With Cast iron Right LPG: 45mm 1W+2SR+1A 30.5MJ/h 29.5MJ/h LPG: ECT900GX 1W+1R +2SR With Cast iron Front 45mm 39.6MJ/h ECT900GX2 39.0MJ/h *Note: For burner: W=Triple Ring Wok burner, R=Rapid burner, SR=Semi-Rapid burner, A=Auxiliary burner... - Page 6 (h x w x d) mm ( w x d)mm ECT60WCX 85x580x500 552 x 470 220-240V/50Hz 0.5W ECT600GS 85x580x500 552 x 470 220-240V/50Hz 0.5W ECT60GX 85x580x500 552 x 470 220-240V/50Hz 0.5W ECT900GX 85x860x500 827 x 470 220-240V/50Hz 0.5W ECT900GX2 85x860x500 827 x 470 220-240V/50Hz 0.5W...
-
Page 7: Installation
TO BE INSTALLED ONLY BY AN AUTHORIZED PERSON. 1. Cupboard Cutting Bench top thickness, 30– 40 mm (3 – 4 cm). Model: ECT60WCX,ECT600GS, ECT60GX Model: ECT900GX. ECT900GX2... - Page 8 2. Place Burner Box Apply the adhesive sealing tape to the underside lip of the burner box. Shown at G opposite. Place burner box into cutout hole and fit clamping brackets to clamp the hotplate to the bench. 3. Fit Burners And Trivet. Replace burners and ensure they are correctly repositioned over the ignitor (S) and thermocouple (T).
-
Page 9: Setting The Gas Pressure
After having installed the hotplate, the GPO must always be in an accessible position. ECT60WCX , ECT600GS, ECT60GX ECT900GX.ECT900GX2 Wiring diagram 4. Gas Connection Install in accordance with relevant gas standards and/or codes of practice applicable. Connect the elbow fitting to the appliance gas manifold connection, and check that seals between the elbow and manifold connection are in place and in good condition. -
Page 11: Gas Conversion Instructions
Change the NG regulator to LPG by a qualified Natural Gas regulator is to be fitted and adjusted person. For model ECT900GX. ECT900GX2 ADJUSTED FOR NATURAL GAS 1.0kPa ADJUSTED FOR ULPG 2.75KPa NOZZLES Gas consumption,... -
Page 12: Start Using Your Appliance
Start Using Your Appliance ECT60WCX，ECT600GS， ECT60GX ECT900GX, ECT900GX2 Description Explanation These show which zone is under control. Zone indicators Flame power Flame power of the zones, is the lowest and is the highest. The hotplates are fitted with mains powered electronic spark ignitors, so must be connected to mains power supply (i.e. - Page 13 Depressing the gas control knob of any burner will activate the spark ignition for all burners. To light the burner, turn the gas control knob to the High Flame setting of the burner to be lit, while at the same time depressing the gas control knob to activate the spark ignition.
-
Page 14: Maintenance And Troubleshooting
Maintenance & Troubleshooting Cleaning and maintenance should be carried out with the appliance cold especially when cleaning the enameled parts. Avoid leaving alkaline or acid substances(lemon juice, vinegar etc.) on the surfaces. STAINLESS STEEL The stainless steel hob of the hotplate must be cleaned regularly (e.g. -
Page 15: Troubleshooting
TROUBLESHOOTING Servicing of the hotplates must only be done by an authorised service representative, and the hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted. DO NOT MODIFY THIS APPLIANCE. It is recommended the hotplate serviced by an authorized person at least every 2 years. This service is not covered by warranty. - Page 16 Pronto Service + Support: 1800 440 335 Email: service@eurostylegroup.com.au HEAD OFFICE 65 Glynburn Road, Glynde SA 5070 Ph: 08 8165 1012 www.euroappliances.com.au...
Need help?
Do you have a question about the ECT900GX2 and is the answer not in the manual?
Questions and answers