Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Euro Appliances EMJGC60SX
Summary of Contents for Euro Appliances EMJGC60SX
- Page 1 EMJGC60SX EMJGC900SX EMJG30WSX COD. 04041MS - 07.07.2016 REV3...
- Page 2 USE, INSTALLATION AND MAINTENANCE INSTRUCTIONS FOR BUILT-IN HOTPLATE Dear Customer Thank you for purchasing a Eurostyle Hotplate. Before we continue telling you about this hotplate, we cordially invite you to become part of the Eurostyle family by subscribing to ongoing information and invitations. You will find that the clean lines and modern look of your Eurostyle Hotplate blends perfectly with your kitchen décor.
- Page 3 DESCRIPTION OF THE HOTPLATE EMJGC60SX EMJGC900SX Overall measurement (mm) Overall measurement (mm) Width 600 x Depth 510 x Height 40 Width 860 x Depth 510 x Height 40 EMJG30WSX Overall measurement (mm) Width 300 x Depth 510 x Height 40...
- Page 4 1) BURNERS Power ratings Burners Pan Ø in cm A diagram is screen-printed above each knob on the NATURAL U-LPG front panel. This diagram indicates to which burner the knob in question corresponds. After having Double crown 22 - 24 opened the gas mains or gas bottle tap, light the 13.7 MJ/h 12.6 MJ/h (item 1 on page 3)
- Page 5 WARNINGS AND ADVICE FOR THE USER: - use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating the mechanical aeration device (suction hood or electric fan fig.
-
Page 6: Care And Maintenance
CLEANING IMPORTANT: - Do not force the taps if they are difficult to open or close. Contact the technical always disconnect the appliance from the gas assistance service for repairs. and electricity mains before carrying out any - Don’t use steam jets for cleaning the hotplate. cleaning operation. -
Page 7: Installation
INSTALLATION TECHNICAL INFORMATION FOR top of the worktop surface must be provided for the INSTALLATION PERSONNEL appliance. 3) INSTALLING THE HOT PLATE This appliance shall be installed only by authorised Check that the appliance is in a good condition after personnel and in accordance with the manufacturer’s having removed the outer packaging and internal installation instructions, local gas fitting regulations,... - Page 8 INSTALLATION 4) FIXING THE HOTPLATE turn the screw “F” until the bracket “S” stick on the top (fig. 10). The hot plate has a special seal which prevents - When the appliance is installed so that the base liquid from infiltrating into the cabinet. Strictly can be touched, we recommend fitting a comply with the following instructions in order to protecting shield.
-
Page 9: Gas Connection
Natural Gas installations require the connection of a the right hand underside of these appliances: gas regulator at the appliance. 90 mm (mod: EMJGC60SX ), Assemble the regulator (noting the gas flow 80 mm (mod: EMJGC900SX ), direction) and transition piece, in accordance with 30 mm (mod: EMJG30WSX). - Page 10 FIG.13 Side Control knob FIG. 12/a FIG.13/A Frontal Control knob FIG.13/B FIG. 12...
-
Page 11: Electrical Connection
INSTALLATION Letter L (live) = brown wire; 6) ELECTRICAL CONNECTION Letter N (neutral) = blue wire; Earth symbol = green - yellow wire. IMPORTANT: the appliance must be installed following the manufacturer's instructions. The - The power supply cable must be positioned so that no manufacturer will not be liable for injury to part of it is able to reach an overtemperature of 90 °C. - Page 12 ADJUSTMENTS Always disconnect the appliance from the electricity main before making any adjustments. 7) TAPS All seals must be replaced by the technician at Our taps are suitable for all the gas, they are male the end of any adjustments or regulations. conical type at one way.
- Page 13 Appliance models: Gas stainless steel hotplate Appliance models: Gas stainless steel hotplate models: models: 6 Burners 6 Burners EMJGC900SX EMJGC900SX EMJGC60SX 4 Burners EMJGC60SX 4 Burners EMJG30WSX 1 Burners EMJG30WSX 1 Burners 1. Remove each burner cap and burner skirt.
-
Page 14: Replacing The Injectors
CONVERSIONS paragraphs 7. The technician must reset any 10) REPLACING THE INJECTORS seals on the regulating or pre-regulating The burners can be adapted to different types of devices. gas by mounting injectors suited to the type of gas The envelope with the injectors and the labels in question. - Page 15 SERVICING CABLE TYPES AND SECTIONS TYPE OF TYPE OF SINGLE - PHASE HOT PLATE CABLE POWER SUPPLY H05 RR - F Section 3 X 0.75 mm Gas hot plate ATTENTION!!! If the power supply cable is replaced, the installer should leave the ground wire (B) longer than the phase conductors (fig.
-
Page 16: Technical Assistance And Spare Parts
TECHNICAL ASSISTANCE AND SPARE PARTS Before leaving the factory, this appliance will have been tested and regulated by expert and specialised personnel in order to guarantee the best performances. Any repairs or adjustments which may be subsequently required may only be carried out by qualified personnel with the utmost care and attention.
Need help?
Do you have a question about the EMJGC60SX and is the answer not in the manual?
Questions and answers