Advertisement
Advertisement
Related Manuals for Euro Appliances EIS900B
Summary of Contents for Euro Appliances EIS900B
- Page 1 Instructions for use and installation Induction cooktop EIS900B...
- Page 2 I The Manufacturer strives for continuous improvements. For this reason, the text and illustrations in this book are subject to change without notice.
-
Page 3: Table Of Contents
The built-in ceramic-glass cooktop is intended for household use only. Dear customer! Materials used for packaging are nature friendly and may be recycled, deposited or destroyed without any threats to the environment. In order to recognize these features, all packing materials are marked with relevant symbols. -
Page 4: Important Warnings
• The appliance may be built-in and connected to the power supply only by a IMPORTANT WARNINGS qualified technician. • Particular areas of the cooktop surface (adjacent to the hotplates) are hot during operation. Prevent the children to hang around the appliance and warn them properly against the danger of burns. -
Page 5: Mounting The Built-In Cooktop
MOUNTING THE BUILT-IN COOKTOP Caution ! • To avoid any possible hazard, the appliance may be installed by qualified personnel only. • Panels and furniture lining of the kitchen cabinet receiving the hob must be treated with temperature resistant adhesives 100°C (otherwise they might be discoloured or deformed because of inadequate temperature resistance). -
Page 6: Connection To The Power Supply
Installing the foam Before inserting the appliance into the opening in the kitchen worktop, the supplied foam gasket must be attached to the lower side of the glass ceramic gasket (glass) cooking hob. Do not install the appliance without the foam gasket! The gasket should be attached to the appliance in the following way: ▪... -
Page 7: Tecnical Information
If it is necessary to disconnect the appliance after installation the disconnection may be achieved by having a plug accessible or by incorporating a switch in the fixed wiring in accordance with the wiring rules. Type EIS900B Width Rated voltage 220-240 V~ or 380-415 V 3N~, 50/60 Hz... - Page 8 • Ceramic glass hob is fitted with three or four hotplates. Hob surface is Hotplate function principle completely flat and smooth, without edges to accumulate dirt. • The hob is fi tted with high power induction hotplates. Heat is generated directly at the bottom of the dish, where it is most needed, without any losses through the ceramic glass surface.
- Page 9 Heating power of the hotplates may be set at nine different levels. Power regulation The following chart indicates illustrative use of each power setting. Power Purpose Setting Off, using remaining heat Maintaining warm food, slow simmer of smaller quantities Slow simmer (continuation of cooking after a powerful start-up) Slow cooking (continuation) of larger quantities, roasting larger chunks Roasting, browning...
-
Page 10: Ceramic-Glass Cooktop
CERAMIC-GLASS COOKTOP 1.Induction hotplate rear left 2.Induction hotplate rear central 3.Induction hotplate rear right 4.Induction hotplate front right 5.Induction hotplate front central 6.Induction hotplate front left 7.Hob control panel Hob control elements A. ON/OFF sensor of cooking zones B. Safety lock on/off and child lock sensor C. - Page 11 Continuous pressing of »+» (E) or »-« (D) sensors the power level is automatically increased or reduced. Another procedure is to change power in steps is by intermediate touching of relevant sensors. Setting is always possible for one hotplate only at the time. Power display indicates »0«, or „H“, depending on the existing temperature of the hotplate (see Section Remaining Heat Indicator).
- Page 12 selected cooking level and limited power for a few seconds. Activating extra powerful setting • First select the hotplate by touching its relevant sensor (A), and immediately after press the sensor (D) then press (E) . Extra powerful setting is on, and power indicator displays symbol “P”.
- Page 13 Decimal dot is on. • Touch the timer ON/OFF sensors (E+D) to activate the timer. • By touching sensors »+« or »-« (E or D) set the new desired cooking time. Remaining cooking time You can display the remaining cooking time by touching the hotplate ON/OFF sensor (A) and then (E+D) or by activating at the same time again and again (D+E) keys, the time that will be showed is refered to to the zone that displays the dot blinking.
-
Page 14: Safety Functions And Error Display
Safety functions and error display. ERROR CODE ERROR DESCRIPTION INSTRUCTION MANUAL Temperature limits are excessed. System must cool down. If the problem persist CONTACT AUTHORIZED CENTER FOR TECHNICAL ASSISTANCE - SPECIFYING THE ERROR CODE Unsuitable pot. The error is automaticly cancelled after 8sec and the coking zone can be used again. -
Page 15: Cleaning And Maintenance Of Ceramic-Glass Hob
CLEANING AND MAINTENANCE OF CERAMIC-GLASS HOB Ceramic glass hob should be cleaned only when completely cooled down, preferably after each use, otherwise even the slightest stains remaining after cooking may burn into the hob surface with each following use. For regular maintenance of ceramic-glass hob use special cleansing agents, produced in such way to create protective film upon the surface. - Page 20 LIB30622...
Need help?
Do you have a question about the EIS900B and is the answer not in the manual?
Questions and answers