Related Manuals for Euro Appliances ECT600GS
Summary of Contents for Euro Appliances ECT600GS
- Page 1 U S A G E A N D C A R E G U I D E PRODUCT CODE: PRODUCT CODE: ECT600GS ECT60WCX ECT60GX ECT900GX...
-
Page 2: General Safety
This manual explains the proper installation and use of your appliance, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference. In case of failure, only the Authorized Technical Service may repair this hob. -
Page 3: Children's Safety
Children’s Safety ⚫ The cooking zones will become hot when you cook. Therefore, always keep small children away from the appliance. ⚫ The appliance is not intended for use by young children or infirm persons without supervision. ⚫ Young children should be supervised to ensure that they do not play with the appliance. Safety During Use ⚫... -
Page 4: How To Avoid Damage To The Appliance
AS/NZS 3000 – Electrical Installations (Wiring Rules) Building codes Any other relevant statutory regulations. ⚫ Check the gas type label on the underside of the hotplate, adjacent to the gas connection to ensure it corresponds to the installation gas supply. If in doubt contact the supply authority. - Page 5 Product Description Burner ECT600GS Pan support Panel knobs Model Burner* Knob Total gas Over view supports position consuption ECT600GS 1W+2SR+1A With Front LPG: Enamel 27.5MJ/h 26.0MJ/h ECT60WCX 1W+2SR+1A With Cast iron Front LPG: 30.5MJ/h 29.5MJ/h ECT60GS 1R+2SR+1A With Cast iron...
-
Page 6: Technical Specifications
Model Dimensions Size Connection Power (h x w x d) mm ( w x d)mm 85x580x500 552 x 470 220-240V/50Hz 0.5W ECT60WCX ECT600GS 85x580x500 552 x 470 220-240V/50Hz 0.5W ECT60GX 85x580x500 552 x 470 220-240V/50Hz 0.5W ECT900GX 85x860x500 827 x 470 220-240V/50Hz 0.5W... -
Page 7: Before Installation
TO BE INSTALLED ONLY BY AN AUTHORIZED PERSON. 1. Cupboard Cutting Bench top thickness, 30– 40 mm (3 – 4 cm). Model: ECT60WCX,ECT600GS, ECT60GX Model: ECT900GX... -
Page 8: Electrical Connection
2. Place Burner Box Apply the adhesive sealing tape to the underside lip of the burner box. Shown at G opposite. Place burner box into cutout hole and fit clamping brackets to clamp the hotplate to the bench. 3. Fit Burners And Trivet. Replace burners and ensure they are correctly repositioned over the ignitor (S) and thermocouple (T). - Page 9 After having installed the hotplate, the GPO must always be in an accessible position. ECT60WCX , ECT600GS, ECT60GX ECT900GX Wiring diagram 4. Gas Connection Install in accordance with relevant gas standards and/or codes of practice applicable. Connect the elbow fitting to the appliance gas manifold connection, and check that seals between the elbow and manifold connection are in place and in good condition.
- Page 11 The manufacturers servicing instructions detail how authorised personnel may convert the hotplate from Natural gas to Universal LPG or from Universal LPG to Natural gas. Contact the manufacturer or agent as required. For model ECT60WCX，ECT600GS，ECT60GX ADJUSTED FOR NATURAL GAS 1.0kPa ADJUSTED FOR ULPG 2.75KPa...
- Page 12 Start Using Your Appliance ECT60WCX，ECT600GS， ECT60GX ECT900GX Description Explanation These show which zone is under control. Zone indicators Flame power Flame power of the zones, is the lowest and is the highest. The hotplates are fitted with mains powered electronic spark ignitors, so must be connected to mains power supply (i.e.
- Page 13 Depressing the gas control knob of any burner will activate the spark ignition for all burners. To light the burner, turn the gas control knob to the High Flame setting of the burner to be lit, while at the same time depressing the gas control knob to activate the spark ignition. Once the burner is alight continue to depress the gas control knob for 5 –...
-
Page 14: Maintenance
Maintenance & Troubleshooting Cleaning and maintenance should be carried out with the appliance cold especially when cleaning the enameled parts. Avoid leaving alkaline or acid substances(lemon juice, vinegar etc.) on the surfaces. STAINLESS STEEL The stainless steel hob of the hotplate must be cleaned regularly (e.g. - Page 15 TROUBLESHOOTING Servicing of the hotplates must only be done by an authorised service representative, and the hotplate must not be modified. Power must be disconnected before any servicing or maintenance is conducted. DO NOT MODIFY THIS APPLIANCE. It is recommended the hotplate serviced by an authorized person at least every 2 years. This service is not covered by warranty.
- Page 17 Pronto Service + Support: 1800 440 335 Email: service@eurostylegroup.com.au HEAD OFFICE 65 Glynburn Road, Glynde SA 5070 Ph: 08 8165 1012 www.euroappliances.com.au...
Need help?
Do you have a question about the ECT600GS and is the answer not in the manual?
Questions and answers