Download
Share
Print this page
Tyco Simplex 4100U-S1 Installation & Maintenance
  1. Manuals
  2. Brands
  3. Tyco Manuals
  4. Control Panel
  5. Simplex 4100U-S1
  6. Installation & maintenance
Tyco Simplex 4100U-S1 Installation & Maintenance

Tyco Simplex 4100U-S1 Installation & Maintenance

Fire indicator panel
Hide thumbs

Advertisement

Quick Links

Download this manual
All manuals and user guides at all-guides.com
4100U-S1 Fire Indicator Panel
Installation & Maintenance
Fire
Australian
Installation
Australian
Manual
Installation &
Maintenance
Manual
LT0394

Advertisement

loading
Need help?

Need help?

Do you have a question about the Simplex 4100U-S1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Tyco Simplex 4100U-S1

Summary of Contents for Tyco Simplex 4100U-S1

  • Page 1 All manuals and user guides at all-guides.com Fire 4100U-S1 Fire Indicator Panel Installation & Maintenance Australian Installation Australian Manual Installation & Maintenance Manual LT0394...
  • Page 2 All manuals and user guides at all-guides.com...

  • Page 3: Approvals

    6,313,744 and 6,426,697. SmartSync horn/strobe control; 6,281,789. Approvals Australian Standard AS4428.1 SSL Listing Number afp1682 Manufacture The 4100U-S1 is a Fire Alarm manufactured by Tyco Safety Products for: Tyco Services Fire & Safety 47 Gilby Road Notting Hill VIC 3168...

  • Page 4: Non-Disclosure Agreement

    All manuals and user guides at all-guides.com Non-Disclosure Agreement Tyco (THE COMPANY) and the User of this/these document(s) desire to share proprietary technical information concerning electronic systems. For this reason the company is disclosing to the User information in the form of this/these document(s).

  • Page 5: Model Number & Firmware Revision

    All manuals and user guides at all-guides.com Model Number & Firmware Revision This manual applies to product with the following: Model number : 4100U-S1 Firmware revision : 11.10 and on Document Document Name : LT0394 4100U-S1 Installation & Maintenance Manual Issue : V1.0 5 July 2006 Amendment Log...

  • Page 6: Cautions, Warnings, And Regulatory Information

    All manuals and user guides at all-guides.com Cautions, Warnings, and Regulatory Information READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in this installation manual. These instructions must be followed to avoid damage to this product and associated equipment. Product operation and reliability depends upon proper installation.

  • Page 7: Table Of Contents

    All manuals and user guides at all-guides.com Table of Contents Copyrights and Trademarks .....................i Approvals..........................i Manufacture........................i Product / Site ........................i Non-Disclosure Agreement ..................... ii End User Liability Disclaimer................... ii Model Number & Firmware Revision................iii Document ........................iii Amendment Log ......................iii Cautions, Warnings, and Regulatory Information............
  • Page 8 All manuals and user guides at all-guides.com Overview ........................2-9 Step 2. Mounting Card Bays to Cabinets ..............2-9 Overview ........................2-9 Step 3. Configuring Cards ................... 2-9 Overview ........................2-9 CPU Motherboard Configuration ................2-9 CPU Daughter Card Configuration ................ 2-10 SPS Configuration ....................
  • Page 9 All manuals and user guides at all-guides.com Overview ........................3-7 CPU Motherboard Jumper Settings................ 3-7 NIC Card Address Setting ..................3-7 NIC Card Jumper Settings..................3-8 Wired Media Card Jumper Settings................ 3-8 Step 2. Mounting Media Cards to the NIC..............3-9 Overview ........................
  • Page 10 All manuals and user guides at all-guides.com AIU/PPU Wiring ..................... 4-10 ASE Mounting......................4-10 ASE Wiring......................4-10 Chapter 5 SPS Field Wiring (4100U-S1)..........5-1 Introduction ......................5-1 In this Chapter ......................5-1 General Field Wiring Guidelines.................. 5-2 General Guidelines ....................5-2 SPS NAC Field Wiring Guidelines................
  • Page 11 All manuals and user guides at all-guides.com Configuring the Card....................6-5 Overview ........................6-5 Setting the Shield Tie Point ..................6-5 Setting the Address ....................6-5 Wiring to IDNet Devices ....................6-6 Overview ........................6-6 Guidelines ........................ 6-6 Notes........................6-7 Class A Wiring ......................
  • Page 12 All manuals and user guides at all-guides.com Appendix D Earth Fault Detection.............D-1 Overview ........................D-1 General Guidelines ......................D-2 Earth Fault Searching from the Front Panel..............D-3 Overview ........................D-3 Access Level Selection....................D-3 Starting the Earth Fault Search ................D-3 Search Option A: Select Location................D-4 Search Option B: Select Channel................D-5 Search Option C: Last Search Result..............D-5 Completing the Search ....................D-5...

  • Page 13: List Of Figures

    All manuals and user guides at all-guides.com List of Figures Figure 1-1. Basic 4100U-S1 System ................1-2 Figure 2-1. CPU Motherboard (566-227) ............... 2-3 Figure 2-2. CPU Card (566-149) ..................2-4 Figure 2-3. Operator Interface ..................2-6 Figure 2-4. System Power Supply.................. 2-7 Figure 2-5.
  • Page 14 All manuals and user guides at all-guides.com List of Tables Table 2-1 Master Controller LEDs 1 through 4 ..........2-5 Table 2-2 Switch/LED Format..............2-22 Table 2-3 Switch Status ................2-22 Table 3-1 4100 NIC & Media Cards – Electrical and Environmental Specifications................3-7 Table 3-2 Wiring Distances.................3-11 Table 3-3...

  • Page 15: Chapter 1 Introduction To The 4100U-S1 Fire Alarm System

    All manuals and user guides at all-guides.com Chapter 1 Introduction to the 4100U-S1 Fire Alarm System Introduction The 4100U-S1 is a compact version of the 4100U fire alarm, which is intended for use in applications requiring only one or two loops of addressable devices. This chapter is an overview of basic system concepts.

  • Page 16: Basic Configuration

    All manuals and user guides at all-guides.com Basic Configuration Overview The basic version of the 4100U-S1 is used for smaller or single-building applications. It is ideally placed in a small building that requires a limited number of notification appliances and initiating devices. If a small building is being expanded, or if other buildings are being constructed in the same general area (as in a campus application), the basic 4100U-S1 can be expanded via networking into one of the larger systems described in Chapter 3.

  • Page 17: 4100U-S1 Part Codes

    All manuals and user guides at all-guides.com 4100U-S1 Part Codes Overview This section lists the parts that are supported by the 4100U-S1 Fire Alarm System. Assemblies, Cards & The following is a list of assemblies, cards and modules used in 4100U-S1: &...

  • Page 18: Labels (Expansion/Spares)

    All manuals and user guides at all-guides.com 4100U-S1 Part Codes, Continued • LB0602 Operator I/F ISO/Test Card Labels • (expansion/spares) LB0605 Fan Control Zone Insert Card • 526-873 Slide In Label, LED Switch Module, 1 Sheet of 6 • 4100-1294 LED Module Slide In Labels, Panel Set •...

  • Page 19: Introduction

    All manuals and user guides at all-guides.com Chapter 2 Installing 4100U-S1 Components This chapter describes how to mount the 4100U-S1 cabinet to a wall, and how to mount Introduction system card bays into the cabinets, modules to bays, etc. Most of a 4100U-S1 is already assembled within the factory. Steps 2 to 6 below are therefore not typically required in the field, but are included for reference.

  • Page 20: Introduction To 4100U-S1 Cabinet

    All manuals and user guides at all-guides.com Introduction to 4100U-S1 Cabinet Overview The 4100U-S1 cabinet contains the CPU, operator interface, system power supply (SPS), backup batteries, and any additional modules that the panel requires. Bays These items are organized into sub-assemblies called bays or card frames, each with a swing-down front door.

  • Page 21: Cpu Motherboard

    All manuals and user guides at all-guides.com Introduction to 4100U-S1 Cabinet, Continued CPU Motherboard The 4100U CPU motherboard holds the CPU card, which is central to the 4100U-S1 system. It is mounted in the CPU bay, occupying two slots of space immediately beside the power supply.

  • Page 22: Cpu Card

    All manuals and user guides at all-guides.com Introduction to 4100U-S1 Cabinet, Continued CPU Card The CPU card mounts onto the CPU motherboard. The CPU card contains a service port, a direct drive user interface connection, and a port for a service modem. MODEM SERVICE MODEM SERVICE PORT...

  • Page 23: Cpu Card Leds

    All manuals and user guides at all-guides.com Introduction to 4100U-S1 Cabinet, Continued CPU Card LEDs The CPU card LEDs indicate Bootloader status as shown in the table below. Table 2-1. CPU Card LEDs 1 through 4 Status LED4 LED3 LED2 LED1 Condition Bootloader...

  • Page 24: Operator Interface

    All manuals and user guides at all-guides.com Introduction to 4100U-S1 Cabinet, Continued Operator Interface The operator interface lets a user operate the panel. It provides alarm, fault, and isolate status alerts, and lets the user review historical logs and perform diagnostics. Figure 2-3.

  • Page 25: Figure 2-4. System Power Supply

    All manuals and user guides at all-guides.com Introduction to 4100U-S1 Cabinet, Continued The basic 4100U-S1 has a Fuse Distribution Board mounted on the SPS chassis and connected to the Auxiliary Power terminals. This provides four sets of supply terminals, each individually fused at 1A, but the collective capacity is still limited to 2A from the Auxiliary Power supply.

  • Page 26: The Power Distribution Interface (Pdi)

    All manuals and user guides at all-guides.com Introduction to 4100U-S1 Cabinet, Continued The Power In the expansion bay, power and data are distributed via the power distribution interface Distribution (PDI). The PDI is a wiring board with eight card slots, each of which can accommodate a Interface (PDI) 4-inch (102 mm) x 5-inch (127 mm) slave card.

  • Page 27: Step 1. Mounting Cabinets

    All manuals and user guides at all-guides.com Step 1. Mounting Cabinets Overview The important aspects of mounting the cabinet are: • Access for the operator; • Height of displays and controls; • Free space for door opening; • Cable entry for field wiring. Refer to AS1670.1 for the height requirement and minimum access requirements.

  • Page 28: Cpu Daughter Card Configuration

    All manuals and user guides at all-guides.com Step 3. Configuring Cards, Continued Note: Some devices that connect to RUI have inherently grounded shield terminals, in which case 24 C cannot be used. If 24 C is used, a Negative Ground Fault will occur. P10/P11: P10 is associated with Port 1 and P11 is associated with Port 2.

  • Page 29: Step 4. Interconnecting Modules And Bays

    All manuals and user guides at all-guides.com Step 4. Interconnecting Modules and Bays Overview Each card has to be interconnected with every other card in its bay. At the same time, bays in the 4100U-S1 also have to be connected together. Read this section to ensure that cards and bays are interconnected correctly.

  • Page 30: Connecting To Motherboards

    All manuals and user guides at all-guides.com Step 4. Interconnecting Modules and Bays, Continued Connecting to Panels with legacy motherboards in the expansion bay require some non-PDI Motherboards connections. If you need to connect a harness to a motherboard, refer to Figure 2-6 and follow these steps.

  • Page 31: Step 5. Installing Modules Into Expansion Bays

    All manuals and user guides at all-guides.com Step 5. Installing Modules into Expansion Bays Overview This section contains guidelines and instructions on installing 4”x 5” cards and traditional motherboards into the 4100U-S1 expansion bay. IMPORTANT: This section applies to aftermarket modules for expansion bays only. If you do not need to install any aftermarket modules at all, you have completed the panel installation and can apply AC power.

  • Page 32: Figure 2-8. Expansion Bay Motherboard Placement

    All manuals and user guides at all-guides.com Step 5. Installing Modules into Expansion Bays, Continued • Placement Motherboards can be installed on top of the PDI in expansion bays. The data and Guidelines power that would normally be bussed via the PDI are routed across the motherboards (continued) via their left and right connectors (J1 and P1).

  • Page 33: Figure 2-9. Slave Card/Pdi Connection

    All manuals and user guides at all-guides.com Step 5. Installing Modules into Expansion Bays, Continued Installing 4” X 5” The power distribution interface (PDI) is mounted to the back of the expansion bay. The Cards PDI contains slots for up to eight 4”x 5” slave cards. Since the PDI carries power and data across the entire bay, it solves most interconnection issues, especially between 4”x 5”...

  • Page 34: Installing Motherboards

    All manuals and user guides at all-guides.com Step 5. Installing Modules into Expansion Bays, Continued Installing Use the following procedure when installing motherboards in an expansion bay. Start Motherboards with the third slot from the left and fill to the right. The mounting items are available as kit 4100-KT0468.

  • Page 35: Step 6. Installing Led/Switch Modules Into Expansion Bays

    All manuals and user guides at all-guides.com Step 6. Installing LED/Switch Modules into Expansion Bays Overview The LED/switch user interface consists of a variety of modules, mounted to the front of an expansion bay, which are configured via the 4100U Programmer. Each display module contains between 8 and 24 switches and LEDs, each one separately configurable.

  • Page 36: The Led/Switch User Interface

    All manuals and user guides at all-guides.com Step 6. Installing LED/Switch Modules into Expansion Bays, Continued Below is an illustration of a LED/switch bay from the user’s perspective. The LED/Switch User Interface Figure 2-11. LED/Switch Modules LED/Switch The LED/switch controller card is a 4100 slave that mounts behind two LED/switch Controller Card modules.

  • Page 37: Configuring The Led/Switch Controller Card

    All manuals and user guides at all-guides.com Step 6. Installing LED/Switch Modules into Expansion Bays, Continued LED/Switch If more than 32 zones are required, a second controller (4100-1289) will be required. Controller Card, (continued) Note that an ME0456 fan control module counts as 8 zones when adding up the controller requirements.

  • Page 38: Figure 2-14. Controller Card Mounting

    All manuals and user guides at all-guides.com Step 6. Installing LED/Switch Modules into Expansion Bays, Continued Mounting the Refer to the figures and instructions below to mount the LED/switch controller card Additional LED/ assembly to the back of one of the LED/switch cards. Switch Controller Card 1.

  • Page 39: Wiring Instructions

    All manuals and user guides at all-guides.com Step 6. Installing LED/Switch Modules into Expansion Bays, Continued LED/Switch Modules All types of modules are mounted to the front of a bay, and are connected to each other via a ribbon cable. Each module operates by the same rules: when a button is pressed, the controller card sends the CPU the information, and the action programmed for that button occurs.

  • Page 40: 4100U Fan Control Module

    All manuals and user guides at all-guides.com 4100U Fan Control Module Overview The ME0456 is a 4100U style Switch/LED display module designed specifically for fan control. It complies with the requirements of AS 1668.1:1998. It has rotary switches and LEDs for 4 sets of fans. In order to accommodate the required rotary switches, the front plate is joggled forward so that it protrudes through the trim.

  • Page 41: Figure 2-16. Me0456 Fan Control Module

    All manuals and user guides at all-guides.com Figure 2-16. ME0456 Fan Control Module 2-23...
  • Page 42 All manuals and user guides at all-guides.com 2-24...

  • Page 43: Introduction

    All manuals and user guides at all-guides.com Chapter 3 Networking Introduction A basic 4100U-S1 system becomes a network node when a Network Interface Card (NIC) or other compatible network card is installed and connected to another network node. How network cards connect to each other depends on the type of media cards being used. In this Chapter Refer to the page number listed in this table for information on a specific topic.

  • Page 44: Network Configuration

    All manuals and user guides at all-guides.com Network Configuration Overview Multiple 4100U-S1 panels can be connected together into a network system by using network interface cards (NICs). When a NIC is installed into a 4100U-S1, it is used to connect to other network nodes. Nodes may consist of other 4100U-S1 or larger 4100U panels, or they may be other types of node such as Graphical Command Centers (GCCs), or Visual Command Centers (VCCs).

  • Page 45: Connecting Loops

    All manuals and user guides at all-guides.com Network Configuration, Continued Connecting Loops Network rings or loops can be joined via physical bridge cards. There may be no more than two network loops connected in tandem. For every two loops that are interconnected (using one physical bridge), there can be a maximum of three other physical bridges used in a star configuration.

  • Page 46: Getting Started

    All manuals and user guides at all-guides.com Getting Started Overview This chapter describes how to turn a basic 4100U-S1 into a network node. This process consists of the following: Step 1. Mounting media cards to the network interface card (NIC) Step 2.

  • Page 47: Network Module Illustrations

    All manuals and user guides at all-guides.com Introduction to the 4100 Network Interface Card (NIC), Continued Network Module Illustrations DATA TRANSMIT/ RECEIVE LEDs (LED2 THROUGH LED5) MEDIA CARD 40-PIN CONNECTORS (P5, P6) DATA RATE JUMPER PORT (P3) DATA PROTOCOL JUMPER PORT (P3) MOTHERBOARD ADDRESS DIP...

  • Page 48: Nic Media Cards

    All manuals and user guides at all-guides.com Introduction to the 4100 Network Interface Card (NIC), Continued NIC Media Cards There are two approved modules that can be plugged into the 4100-6014 NIC: • 4100-6057 Fiber-Optic Media Card (565-261) • 4100-6056 Wired Media Card (565-413) Each module is shown below.

  • Page 49: Requirements And Limitations

    All manuals and user guides at all-guides.com Introduction to the 4100 Network Interface Card (NIC), Continued Requirements and Limitations Table 3-1. 4100 NIC & Media Cards - Electrical and Environmental Specifications Electrical Specifications Network Startup, no media cards: 8 VDC @ 110 mA Interface Card Nominal, no media cards: 20 to 32 VDC @ 0 mA Using 24 V power supply: 20 VDC @ 140 mA max.

  • Page 50: Nic Card Jumper Settings

    All manuals and user guides at all-guides.com Step 1. Configuring Network Cards, Continued NIC Card There are two jumper settings on the NIC card: P3 and P4. Jumper Settings P3: Determines the NIC data transmission rate, 57.6 kbits/second or 9600 bits/second. •...

  • Page 51: Step 2. Mounting Media Cards To The Nic

    All manuals and user guides at all-guides.com Step 2. Mounting Media Cards to the NIC Overview The 4100-6014 Network Interface Card (NIC) uses media cards to connect to other NICs. This section describes how the media cards are mounted onto NICs. Media Card NICs connect to each other via the two types of media cards.

  • Page 52: Step 4. Wiring Network Cards

    All manuals and user guides at all-guides.com Step 4. Wiring Network Cards Overview The nodes in the network now have to be wired together, so that the NIC in one host panel connects to the NIC in the next panel. Wiring Guidelines Refer to the following guidelines field wiring General...

  • Page 53: Wiring Distances

    All manuals and user guides at all-guides.com Step 4. Wiring Network Cards, Continued Wiring Distances Maximum wiring distances are shown in the table below. Table 3-2. Wiring Distances Media Type Size Data Rate Max Distance 0.2 mm 57.6 kbps 2,100m unscreened 9.6 kbps 3,600m...

  • Page 54: Fiber-Optic Wiring

    All manuals and user guides at all-guides.com Step 4. Wiring Network Cards, Continued Fiber-Optic Wiring Connectors U1 (transmitter) and U2 (receiver) on the 4100-6057 Fiber-Optic Media Card are used to connect 4100-6014 NICs across parts of a network. Note: ST connectors with long strain relief boots must be used with the fiber optic cable.

  • Page 55: 4190-9010 Coupler Requirements

    All manuals and user guides at all-guides.com Step 4. Wiring Network Cards, Continued 4190-9010 Coupler The 4190-9010 Coupler is used with the 4100-6057 Fiber Optic Media Board, revision Requirements “C” or higher. Two 4190-9010 Bi-Directional Couplers are required per connection, one at each node.

  • Page 56: Figure 3-7. Coupler Wiring

    All manuals and user guides at all-guides.com Step 4. Wiring Network Cards, Continued 4190-9010 Coupler The illustration below shows coupler wiring. Requirements (continued) Figure 3-7. Coupler Wiring Wiring with the Refer to the guidelines and figures in this topic to use wired media cards. Wired Media Card IMPORTANT: TB1 on the wired media card must not be used when it is connected to the 4100-6014 NIC.

  • Page 57: Wiring With The Wired Media Card

    All manuals and user guides at all-guides.com Step 4. Wiring Network Cards, Continued Wiring with the Figure 3-8, below, shows how CPU motherboards in two 4100U-S1s with wired media Wired Media Card network cards connect to each other. The right port terminals (TB3) on one 4100U-S1 (continued) are connected to the left port terminals (TB1) of the other 4100U-S1.

  • Page 58: Loop Wiring, Mixed Fiber And Cable

    All manuals and user guides at all-guides.com Step 4. Wiring Network Cards, Continued Loop Wiring, mixed Figure 3-9 shows an example of loop network cabling using a mixture of fibreoptical Fiber and Cable cable and twisted pair. Note that the left port of any network card is connected to the right port of the next network card regardless of whether the connection is fiber or copper.

  • Page 59: Chapter 4 The System Power Supply & Alarm Relay Card

    All manuals and user guides at all-guides.com Chapter 4 The System Power Supply & Alarm Relay Card Introduction The system power supply (SPS) is described in Chapter 2. A picture of it is shown in Figure 2-4. This chapter has the current and voltage ratings of the SPS and describes how it is installed and configured by the factory.

  • Page 60: Sps Specifications

    All manuals and user guides at all-guides.com SPS Specifications Input/Output/Battery The following table summarizes the specifications for the SPS. Specifications Table 4-1. SPS Input and Output Specifications AC Input Specifications SPS in Basic 4100U- 240 VAC + 6% -10% @ 50 Hz S1 (4100-9848AU) 2 A Maximum DC Output Specifications...

  • Page 61: Sps Current Consumption

    All manuals and user guides at all-guides.com SPS Specifications, Continued • The bulk supply (rated at 9A max) which feeds 24V Sig, 24V Card, 24V Aux also supplies the SPS Card including the on board IDNet, and the battery charger. The charger is disabled during alarms so as to make the 9A available on the other busses.

  • Page 62: Sps Adjustments

    All manuals and user guides at all-guides.com SPS Specifications, Continued • Additional alarm conditions: Trouble relay activated, power trouble LED on, IDNet LED on, battery charger off, auxiliary power load = 0 mA, NAC alarm load = 0 mA, IDNet = 35 V SPS Adjustments Adjusting Voltages There are two 4mm (i.e.

  • Page 63: Sps Led Indications

    All manuals and user guides at all-guides.com SPS LED Indications Status LEDs The SPS has the following LEDs: LED1 (yellow). Illuminates when NAC 1 is ON or in Fault. LED2 (yellow). Illuminates when NAC 2 is ON or in Fault. LED3 (yellow).

  • Page 64: Troubleshooting An Sps

    All manuals and user guides at all-guides.com Troubleshooting an SPS Overview This section contains explanations of fault messages associated with the SPS that may appear on the 4100U-S1 display. Heading text in the left margin shows the error message, while the paragraph next to it describes the likely cause of the message. “IDNet Power There is no output voltage from the power supply.

  • Page 65: The Alarm Relay Card

    All manuals and user guides at all-guides.com The Alarm Relay Card Overview The Alarm Relay Card mounts on, and is driven by, the SPS. It has 3 relays, each providing one set of voltage-free contacts. It is fitted to the basic 4100U-S1 as standard. The relays are able to be configured under custom control, but the default operation is for system status, i.e.

  • Page 66: Configuration

    All manuals and user guides at all-guides.com The Alarm Relay Card, Continued Configuration The relays have one set of voltage-free contacts (see note below) connected to one pair of terminals via a header. The two terminals are configured for normally closed or normally open by positioning a jumper on the relay card.

  • Page 67: Brigade Interfaces

    All manuals and user guides at all-guides.com Brigade Interfaces Overview The Alarm Relay Card is typically used to provide a Brigade Interface. The default configuration is for the three relays to operate on Fault (Trouble), Isolate (Supervisory) and Alarm, respectively. Format These relays are normally de-energised and energise on the respective status.

  • Page 68: General Wiring

    All manuals and user guides at all-guides.com General Wiring The ASE or AIU/PPU should be powered from the fused DC distribution board on the power supply. It is recommended that the brigade device does not share its fuse protection with any other equipment, for reliability. The wiring between the brigade device and the 4100U-S1 should be routed neatly as shown in the following drawings, and secured in place with the cable ties and adhesive tie holders supplied with the kits.

  • Page 69: Introduction

    All manuals and user guides at all-guides.com Chapter 5 SPS Field Wiring (4100U-S1) Introduction This chapter shows how various devices are wired to an SPS. It includes connection to NACs, IDNet, relays, and power circuits. In this Chapter Refer to the page number listed in this table for information on a specific topic. Topic See Page # General Field Wiring Guidelines...

  • Page 70: General Field Wiring Guidelines

    All manuals and user guides at all-guides.com General Field Wiring Guidelines General Guidelines • All field wires must be 0.75 mm or greater cross section and comply with AS1670.1 and the wiring code. • Conductors must test free of all earth leakage. •...

  • Page 71: Sps Nac Field Wiring Guidelines

    All manuals and user guides at all-guides.com SPS NAC Field Wiring Guidelines Overview Each of the three NACs on the SPS has two pairs of driven outputs (A+/A-, B+/B-) which operate together. NAC B outputs have polarity reversal supervision and expect a 10k EOLR. Each connected device must have a suitably rated blocking diode.

  • Page 72: Class A (Loop) Nac Wiring

    All manuals and user guides at all-guides.com SPS NAC Field Wiring Guidelines, Continued Some or all of these output functions could be implemented using addressable devices or other relay modules instead, in which case the corresponding NAC output could be reassigned to other uses. The new configuration would require full testing of these functions to ensure compliance with AS 4428.1.

  • Page 73: Class B (String) Nac Wiring

    All manuals and user guides at all-guides.com SPS NAC Field Wiring Guidelines, Continued Class B (string) NAC To connect the SPS to appliances using Class B wiring, read the following instructions Wiring and refer to the figure below. 1. Route wire from the B+, B- outputs on TB2 of the SPS to the appropriate inputs on a peripheral notification appliance.

  • Page 74: Power Supply Wiring Distances

    All manuals and user guides at all-guides.com Power Supply Wiring Distances Overview Before wiring from any type of power supply to notification appliances, check Tables 5-1 and 5-2 for wiring distances. Class A NAC Table 5-1 lists the maximum distances from the NAC terminal block to the last appliance Wiring Table in a Class A (loop) configuration, depending on wire gauge and current.

  • Page 75: Class B Nac Wiring Table

    All manuals and user guides at all-guides.com Power Supply Wiring Distances, Continued Class B NAC Table 5-2 lists the maximum distances from the NAC terminal block to the last appliance Wiring Table in a Class B (string) configuration, depending on wire gauge and current. Use Table 5-2 to calculate wire distances for your application if you are using Class B wiring.
  • Page 76 All manuals and user guides at all-guides.com Using T-Gen 50 with 4100U-S1 Overview AS 1670.1 requires fire alarm warning systems to produce sounds complying with AS 2220 or ISO 8201. One way of meeting this requirement in a 4100U system is to use a T-GEN 50 tone generator, which is capable of driving up to 50W of load on a 100V speaker line.

  • Page 77: Using T-Gen 50 With 4100U-S1

    All manuals and user guides at all-guides.com Using T-Gen 50 with 4100U-S1, Continued Controlling a T-Gen 50 with a Relay Module 4100-3003 Relay Module DEF- 10 k ohm A/I/E- resistor ALM- To AUX POWER +24V +24V Auto 150 (1.0 mm or heavier EARTH LINE -...

  • Page 78: T-Gen 50 Setting For Relay Operation

    All manuals and user guides at all-guides.com Using T-Gen 50 with 4100U-S1, Continued T-Gen 50 Setting for Relay Operation These switch and link settings should be used. These apply to T-GEN 50 software version 1.7. Alert to Evacuate Change-Over Time SW2 (T1) Setting on T-GEN 50 (T0)

  • Page 79: Controlling A T-Gen 50 From A Nac Output

    All manuals and user guides at all-guides.com Using T-Gen 50 with 4100U-S1, Continued Controlling a A T-GEN 50 can be controlled and supervised using a NAC output. The NAC is used to T-Gen 50 from a NAC control the ALM- input to the T-GEN 50 and to supervise its Fault relay output. The T- Output GEN 50 is configured to supervise the 100V wiring to the loudspeakers.

  • Page 80: T-Gen 50 Settings For Nac Operation

    All manuals and user guides at all-guides.com Using T-Gen 50 with 4100U-S1, Continued T-Gen 50 Settings for These switch and link settings should be used. These apply to T-GEN 50 software NAC Operation version 1.7. Alert to Evacuate Change-Over Time SW2 (T1) Setting on T-GEN 50 (T0)

  • Page 81: Fitting An Evacuationcontrol

    All manuals and user guides at all-guides.com Using T-Gen 50 with 4100U-S1, Continued An optional three-position control ME0460 (see part numbers in Chapter 1) allows T- Fitting an GEN 50s to be switched from the front panel between automatic operation, being EvacuationControl Isolated, or producing Evacuation tone, regardless of the state of other control inputs.

  • Page 82: Speaker Wiring

    All manuals and user guides at all-guides.com Using T-Gen 50 with 4100U-S1, Continued Refer to the T-GEN 50 Installation and Operating Guide (LT0186) for details about the 100V Speaker wiring of speakers and end-of-line resistor requirements for the T-GEN 50. Wiring ME0460 Evac ME0490...

  • Page 83: Sps Auxiliary Power Wiring

    All manuals and user guides at all-guides.com SPS Auxiliary Power Wiring Overview The panel, battery-backed, unregulated dc bulk power is available from the SPS via the NAC and the 24V Aux power terminals. NACs can be configured as auxiliary power point type in the 4100U Programmer.

  • Page 84: Wiring

    All manuals and user guides at all-guides.com SPS Auxiliary Power Wiring, Continued Wiring The SPS can connect to auxiliary power appliances via the dedicated auxiliary power tap (TB3). If more power is needed, any of the three NAC outputs can be used for auxiliary power.

  • Page 85: Sps Relay Wiring

    All manuals and user guides at all-guides.com SPS Relay Wiring Overview The SPS has one programmable relay, Aux 1, with one set of voltage-free contacts (see below). The Alarm Relay 4100-6033 is fitted as standard to 4100U-S1. This has 3 relays, each with one set of normally open (or normally closed) contacts available on a screw terminal block (see Chapter 4).

  • Page 86: Sps Idnet Wiring

    All manuals and user guides at all-guides.com SPS IDNet Wiring Overview This section describes how the IDNet Channel on the SPS connects to addressable devices/detectors. The guidelines governing IDNet wiring guidelines are covered in Chapter 6, IDNet Installation. IDNet Wiring Up to 250 IDNet initiating devices are supported on the SPS IDNet channel.

  • Page 87: Class A (Loop) Wiring

    All manuals and user guides at all-guides.com SPS IDNet Wiring, Continued Class A (loop) To connect addressable devices/detectors to the SPS IDNet using Class A wiring, read the Wiring following instructions. 1. Ferrite beads are required on the SPS IDNet cables (refer Figure 5.1). 2.

  • Page 88: Class B (String) Wiring

    All manuals and user guides at all-guides.com SPS IDNet Wiring, Continued Class B (string) To connect addressable devices/detectors to the SPS IDNet using Class B wiring, read the Wiring following instructions. 1. Under AS1670.1 Class B wiring is allowed only for a maximum of 40 addressable devices.

  • Page 89: Chapter 6 Installing A 4100U Idnet Card

    All manuals and user guides at all-guides.com Chapter 6 Installing a 4100U IDNet Card Introduction The 4100U-S1 can support one IDNet card in the expansion bay, to provide a second addressable loop. The IDNet Card uses Mapnet Protocol and communicates with existing Mapnet detectors/devices plus the new IDNet devices.

  • Page 90: The Idnet Card

    All manuals and user guides at all-guides.com The IDNet Card The 4100U IDNet card receives 24V power (+24V Card Supply bus) and communication Overview with the CPU via the PDI. There are several versions of IDNet Card, configured by links soldered on the PCB.

  • Page 91: Leds

    All manuals and user guides at all-guides.com The IDNet Card, Continued LEDs The IDNet card has the following LEDs: LED1. Normally off. Turns on steady if the IDNet card is not communicating with the 4100U CPU. LED2. Normally off. Illuminates to indicate a problem with the IDNet lines. •...

  • Page 92: Installing The Idnet Card Onto The Pdi

    All manuals and user guides at all-guides.com Installing the IDNet Card onto the PDI Overview Use connector P2, labelled on the back side of the IDNet card, to connect to any of the four left-most PDI connectors as shown in the figure below. Note that the right-most two PDI connectors are obscured by the mains output bracket, and a T-Gen 50 bracket (if fitted).

  • Page 93: Configuring The Card

    All manuals and user guides at all-guides.com Configuring the Card Overview Configuring the card consists of selecting the shield tie point, and setting the card address. Setting the Shield If a shielded cable is used, connect the cable shield to the dedicated terminal on TB1 and Tie Point use jumper port (P1) to select where the shield will be tied.

  • Page 94: Wiring To Idnet Devices

    All manuals and user guides at all-guides.com Wiring to IDNet Devices Overview Up to 250 IDNet slave devices, such as smoke detectors and manual call points, can be connected to the IDNet card using Class A (loop) or Class B (line) wiring, with the following restrictions.

  • Page 95: Notes

    All manuals and user guides at all-guides.com Wiring to IDNet Devices, Continued Table 6-2 Cable Run Lengths Notes Wire Size 0.75 mm 1 mm 1.5 mm 2.5 mm 4 mm Resistance Distance 385 m 513 m 769 m 1,282 m 2,052 m 20Ω...

  • Page 96: Class B Wiring

    All manuals and user guides at all-guides.com Wiring to IDNet Devices, Continued Class B Wiring To connect the IDNet card to devices using Class B wiring, read the following instructions. 1. On TB1, jumper IDNetB+ to IDNet A+, and jumper IDNetB- to IDNetA-. If the jumper is absent, a Class A Trouble will be indicated on LED 2.

  • Page 97: Troubleshooting On Idnet

    All manuals and user guides at all-guides.com Troubleshooting on IDNet Overview This section describes the messages that may appear on the 4100U-S1 display when using the IDNet card. Trouble messages appear on the left as titles, and possible causes are listed to the right in the text.
  • Page 98 All manuals and user guides at all-guides.com 6-10...

  • Page 99: Chapter 7 Pc Software Connections

    All manuals and user guides at all-guides.com Chapter 7 PC Software Connections Introduction The service port on the door with the Operator Interface enables the 4100U-S1 to connect to a PC running important utilities, such as diagnostics, programming, CPU firmware downloading, and channel monitoring.

  • Page 100: Software Modes

    All manuals and user guides at all-guides.com Software Modes Overview The 4100U-S1 can connect to PC running important utilities, such as diagnostics, programming, CPU firmware downloading, and channel monitoring. It connects to the PC running all of these utilities via the service port on the CPU card. Software Modes There are three basic software modes that the service port or service modem can be used to connect to:...

  • Page 101: Software Modes

    All manuals and user guides at all-guides.com Software Modes, Continued Continued on next page Software Modes Master Bootloader Interface Mode. This mode is used to download the Master CPU (continued) Exec firmware and the CFG.TXT file to the CPU via the serial port. serial download cable Laptop/PC running...
  • Page 102 All manuals and user guides at all-guides.com...

  • Page 103: Chapter 8 Installation Checklist, Commissioning & Maintenance

    All manuals and user guides at all-guides.com Chapter 8 Installation Checklist, Commissioning & Maintenance Introduction The 4100U-S1 is tested in the factory and is loaded with a basic configuration. When the panel arrives on site the installer must unpack and check the panel, mount the cabinet, any additional cards, and check the configuration before applying power.

  • Page 104: Alignment & Adjustment

    All manuals and user guides at all-guides.com Alignment & Adjustment All the 4100U-S1 cards and modules in the base panel are tested and aligned in the Overview factory before being supplied to the customer. The only field adjustment that may be necessary is to set the battery charger voltage.

  • Page 105: Power Up & Placing Into Operation

    All manuals and user guides at all-guides.com Power Up & Placing into Operation To place the 4100U-S1 into operation, perform the following steps: STEP 1 Ensure that the Mains Switch is OFF. STEP 2 Ensure that 240 VAC is connected to the panel from the mains distribution switchboard.

  • Page 106: Maintenance

    All manuals and user guides at all-guides.com Maintenance The 4100U-S1 system must be kept free from faults and tested on a weekly, monthly and annual basis to verify that it is operating correctly. The tests required by part 8 of the standard AS1851 Maintenance of Fire Protection Equipment are detailed in the 4100U-S1 Operator’s Manual, LT0395.

  • Page 107: Appendix A Card Address Dip Switch

    All manuals and user guides at all-guides.com Appendix A Card Address DIP Switch Overview Addressable cards include a bank of eight DIP switches. From left to right (see Figure A- 1, below) these switches are designated as SWx-1 through SWx-8. The function of these switches is as follows: •...

  • Page 108: Table A-1 Card Addresses

    All manuals and user guides at all-guides.com Overview, (continued) Table A-1. Card Addresses Address SW 1-2 SW 1-3 SW 1-4 SW 1-5 SW 1-6 SW 1-7 SW 1-8 Address SW 1-2 SW 1-3 SW 1-4 SW 1-5 SW 1-6 SW 1-7 SW 1-8...

  • Page 109: Appendix B Programming Requirements

    All manuals and user guides at all-guides.com Appendix B Programming Requirements Introduction This appendix briefly summarises the programming that is required to comply with AS4428.1. It does not provide equations or detail of programming. Refer to LT0400 4100U-S1 Programming & Configuration Reference for descriptions of the AS 4428.1 programming.
  • Page 110 All manuals and user guides at all-guides.com...

  • Page 111: Notes

    All manuals and user guides at all-guides.com Appendix C Checking System Wiring Overview This appendix contains instructions on how to use a volt/ohm meter to check system wiring. Using the Volt/ When using the volt/ohm meter to check each circuit, make sure to adhere to the notes Ohm Meter and instructions below.

  • Page 112: Meter Readings

    All manuals and user guides at all-guides.com Appendix C: Checking System Wiring, Continued Meter Readings Table C-1 lists the correct meter readings for indicating appliances and initiating devices. Table C-1. Acceptable Zone and Signal Circuit Meter Readings Circuit Type Meter Reading Class B/Style B Initiating Device (Zone) Circuit From zone + to zone –...

  • Page 113: Appendix D Earth Fault Detection

    All manuals and user guides at all-guides.com Appendix D Earth Fault Detection Overview This appendix contains instructions on how to use the Earth Fault Search feature of the 4100U-S1 diagnostics menus. Earth Fault Search is a diagnostic search of external field wiring that assists in locating circuits with earth faults.

  • Page 114: General Guidelines

    All manuals and user guides at all-guides.com General Guidelines Review the guidelines below before initiating an Earth Fault Search. • The Detect Earth Fault jumper must be installed at the SPS for earth fault detection to occur. • Only one power supply per location is configured to detect earth faults. •...

  • Page 115: Earth Fault Searching From The Front Panel

    All manuals and user guides at all-guides.com Earth Fault Searching from the Front Panel Overview This section describes how to conduct an Earth Fault Search, from selecting the appropriate access code to correcting the fault. Access Level The panel must be at the appropriate access level (1, 2, 3, or 4) in order to run diagnostics. Selection To get to the correct access level, 1.

  • Page 116: Search Option A: Select Location

    All manuals and user guides at all-guides.com Earth Fault Searching from the Front Panel, Continued 10. Press the Enter button. The following options become available when you press Starting the Earth the Next and Previous buttons: Fault Search, Continued Press <NEXT> or <PREVIOUS> to scroll Location Search Press <NEXT>...

  • Page 117: Search Option B: Select Channel

    All manuals and user guides at all-guides.com Earth Fault Searching from the Front Panel, Continued Search Option B: If you select the IDNet Channel Search menu item, a list of IDNet channels to search Select Channel becomes available. Use the Next and Previous buttons to scroll through the list. When the IDNet channel you want to search is shown and "Press <ENTER>...

  • Page 118: Search Results

    All manuals and user guides at all-guides.com Search Results Overview There are several types of results that can display at the end of an Earth Fault Search. This section covers all types of results. IMPORTANT: Once you have been directed to an earth fault and corrected it, it is recommended that you restart the system (warm- or cold-start).

  • Page 119: Fault Not Found

    All manuals and user guides at all-guides.com Search Results, Continued IDNet isolator fault. The message below shows a fault detected after the IDNet isolator Point Faults, was turned on: Continued CARD 2, IDNET CARD (250 POINTS) M1-3, IDNET ISOLATOR EARTH FAULT Fault Not Found If the message in the lower right corner of the LCD reads FAULT NOT FOUND (for a Location Earth Fault Search) or FAULT CLEAR FAIL (for an IDNet Channel Earth Fault...
  • Page 120 All manuals and user guides at all-guides.com...

  • Page 121: Appendix E Related Documentation

    All manuals and user guides at all-guides.com Appendix E Related Documentation The following manuals are relevant. Other Australian 4100U manuals may be found on the TSP website. Book Part Title Number LT0395 4100U-S1 AS4428 FIP OPERATOR'S MANUAL A5 LT0393 4100U-S1 ASE & AIU/PPU DOOR INSTALL INSTRUCTIONS LT0400 4100U-S1 PROGRAMMING AND CONFIGURATION REFERENCE LT0307...
  • Page 122 All manuals and user guides at all-guides.com Book Part Number Title (cont.) (cont.) 4100/4120-Series NIC and Media Modules 579-182 Installation Instructions 4100/4120-Series Physical Bridges and 4100/4120-Series Media Modules 579-184 Installation Instructions 4100/4120-Series Class A / Class B Zone Modules 579-205 Installation Instructions 4100/4120-Series Relay Modules 579-220...

  • Page 123: Appendix F Compatible Actuating Devices

    8 Zone Module Monitor ZAM Monitor ZAM 885WP-B Weatherproof Heat Detector Type B @ Remote indicator output cannot be wired in common with Tyco 614 series or the Minerva M614 series (and most other Tyco/Olsen) detectors. Continued on next page...
  • Page 124 All manuals and user guides at all-guides.com List of Approved Devices, Continued Hochiki Range - Conventional Detectors DCA-B-60R MK V Type A heat detector DCC-A Heat Type A DCC-C Heat Type C DCD-A Heat Type A DCD-C Heat Type C DFE-60B Type B heat detector DCA-B-90R MK 1...
  • Page 125 All manuals and user guides at all-guides.com List of Approved Devices, Continued Brooks Range - Conventional Detectors PFS-A Heat detector Type A PFS-B Heat detector Type B PFS-C Heat detector Type C PFS-D Heat detector Type D PFS-P Photoelectric smoke detector PFS-P MK II Photoelectric smoke detector PFS-I...

  • Page 126: Compatible Detectors, Idnet

    All manuals and user guides at all-guides.com Compatible Detectors, IDNET The following lists the detectors approved for use with IDNet and shows current rating and numbers allowed per loop. Device Type Operating Maximum Maximum Current mA Number Allowed Number Per Loop Allowed Per Line 4098-9714E...

  • Page 127: Compatible Addressable Field Devices, Idnet

    All manuals and user guides at all-guides.com Compatible Addressable Field Devices, IDNet The following lists the addressable devices approved for use with IDNet and shows current rating and numbers allowed per loop. Device Type Operating Maximum Maximum Current mA Addressable Addressable Point On Points on...
  • Page 128 All manuals and user guides at all-guides.com...

  • Page 129: Appendix G 4100U-S1 Specifications

    All manuals and user guides at all-guides.com Appendix G 4100U-S1 Specifications General System Capacity 500 points of addressable devices, plus 500 points of annunciation. Expansion up to 4 x 4100 legacy cards up to 4 x 4” x 5” PDI cards Cabinet Size 1050H x 550W x 280D (mm) Cabinet Material...

  • Page 130: Voltage & Current Ratings Of Modules & Assemblies

    All manuals and user guides at all-guides.com Voltage & Current Ratings of Modules & Assemblies The DC input voltage range of the following modules is 18-33Vdc. The current listed is nominal for 24Vdc, and may be used for battery capacity calculations. Module Name Quiescent...

  • Page 131: Appendix H Power Supply & Battery Capacity Calculations

    All manuals and user guides at all-guides.com Appendix H Power Supply & Battery Capacity Calculations Power Supply Part of the system design includes calculating that the quiescent load and the alarm load are each less than the rating of the power supply. Note that the quiescent load includes devices such as door holders that are normally energized, but get switched off during alarm.
  • Page 132 All manuals and user guides at all-guides.com...

  • Page 133: Appendix I List Of Drawings

    All manuals and user guides at all-guides.com Appendix I List of Drawings The following drawings are included since they are referred to in the manual or are relevant. 1901-267 Sheet 2, 4100U AIU/PSU Wiring Assembly Drawing 1976-176 4100U-S1 Presentation Drawing 1976-174 4100U-S1 Brigade Door Assembly Sheet 1 ASE, Sheet 3 PPU/AIU...
  • Page 134 All manuals and user guides at all-guides.com...
  • Page 135 All manuals and user guides at all-guides.com...
  • Page 136 All manuals and user guides at all-guides.com...
  • Page 137 All manuals and user guides at all-guides.com...
  • Page 138 All manuals and user guides at all-guides.com ©2004 Tyco Safety Products Westminster, Westminster, MA 01441-001 USA. Specifications and other information shown were current as of publication, and are subject to change without notice.