Advertisement
Available languages
Available languages
Quick Links
HEAVY-DUTY 12 TOTE STORAGE RACK
TOOLS REQUIRED
1. Drill with #2
Phillips-Head Tip
2. Screwdriver
PARTS LIST
1. 8 x Horizontal crossbars
2. 4 x Center verticals
3. 2 x Left & right rear corner verticals
4. 1 x Left front corner vertical
5. 1 x Right front corner vertical
6. 4 x Wall mount flanges
7. 4 x Wall mount extensions tubes
8. 24 x Horizontal slide rails
FASTENER LIST
1. 110 x #08 x 3/4 in. Fastening screws
2. 8 x #08 x 1-½ in. Wall mount
Extension tube fastening screws
3. 12 x #10 x 1-½ in. Wall mount
flange screws
4. 12 x Plastic wall anchors
NOTE
HARDWARE IS LOCATED
IN THE TUBES.
Separate all parts into groups
(as shown) and familiarize.
Read all instructions before
beginning assembly.
Solutions Murales PROSLAT inc.
1 888 691-2944
Model # 65012
Assembly instructions
#7
#1
#2
#3
#4
#5
#8
#1
#3
#6
#2
#4
Advertisement
Related Manuals for BIN WAREHOUSE 65012
Summary of Contents for BIN WAREHOUSE 65012
- Page 1 Solutions Murales PROSLAT inc. 1 888 691-2944 Model # 65012 HEAVY-DUTY 12 TOTE STORAGE RACK Assembly instructions TOOLS REQUIRED 1. Drill with #2 Phillips-Head Tip 2. Screwdriver PARTS LIST 1. 8 x Horizontal crossbars 2. 4 x Center verticals 3. 2 x Left & right rear corner verticals 4.
- Page 2 FRONT GRID ASSEMBLY Point all dimples down Alignment dimples Holes down Holes down Short side to floor Other side PARTS NEEDED: STEP 1 STEP 2 4 of #1 2 of #2 4 Horizontal crossbars (#1) inserted through 2 Center Vertical 1 Left front corner vertical (#4) and 1 right front (#2) Tip : When installing second center vertical, stand corner vertical (#5) Placed on horizontal crossbar.
- Page 3 Make sure unit remains in position front side only front side only. at all 4 locations while marking holes. FASTENING BIN WAREHOUSE TO WALL Unit must be attached to wall Move unit away from wall and remove wall Slide unit back against wall while inserting all 4 wall mount extension tubes (#7) into flange from tube and mount flange to wall using...
-
Page 4: Disclaimer Of Liability
Solutions Murales PROSLAT inc. (hereafter Proslat) warrants its Bin Warehouse Rack against defects in material or workmanship for a lifetime period. Proslat will replace any defective Rack as long as it was installed and maintained according to the printed instructions. Any Proslat Bin Warehouse Rack replaced under the terms of the Lifetime Warranty inherits the remaining warranty period from the original purchase. - Page 5 Solutions Murales PROSLAT inc. 1 888 691-2944 Modèle N° 65012 INSTRUCTIONS D’ASSEMBLAGE – SUPPORT ULTRA-ROBUSTE POUR 12 BACS OUTILS REQUIS 1. Tournevis électrique avec tête Phillips # 2 2. Tournevis LISTE DES PIÈCES 1. 8 x Barres horizontales 2. 4 x Barres centrales verticales 3.
- Page 6 ASSEMBLAGE DE LA GRILLE AVANT Autre côté Dessus Pointez les alvéoles vers la bas Encoches d’alignement Trous vers le bas Trous vers le bas Côté court au sol PIÈCES NÉCESSAIRES : ÉTAPE 1 ÉTAPE 2 4 x n°1 2 x n°2 Insérez les quatre barres horizontales (n°...
- Page 7 JOINDRE LA GRILLE AVANT À LA GRILLE ARRIÈRE Côté court au sol ÉTAPE 1 ÉTAPE 2 ÉTAPE 3 Insérez les glissières inférieures (n ° 8) dans la grille Insérez et fixez les 3 prochaines rangées de Tournez l’unité verticalement et placez-la avant et fixez-les (en vous assurant qu’elles sont glissières à...
- Page 8 Cette garantie est valide seulement si la capacité maximale est respectée. Le client, distributeur et/ou l’installateur s’engage à ne pas tenir PROSLAT responsable en cas d’une réclamation concernant un produit Bin Warehouse, si le poids a dépassé la capacité maximale de celui-ci ou que l’installation n’a pas été effectuée selon les instructions du fabricant.
Need help?
Do you have a question about the 65012 and is the answer not in the manual?
Questions and answers