Related Manuals for PSA Products LIFWMB2
Summary of Contents for PSA Products LIFWMB2
- Page 1 All manuals and user guides at all-guides.com Quick Start Guide LIFWMB2 Interlink Network Setup Please Read All Instructions First!
- Page 2 all-gui des.co...
- Page 3 All manuals and user guides at all-guides.com Section 1 Quick Start RF Interlink Network Setup Section 2 Adding a Device to an Existing RF Interlink Network Section 3 Resetting a Device...
- Page 4 All manuals and user guides at all-guides.com LINK button Power Up ONE Device Connect one smoke alarm to the LIFWMB2 RF baseplate. Baseplate LINK button Red LED will ash on/o every second.
- Page 5 All manuals and user guides at all-guides.com Push button twice On the First Powered Device Push the LINK button two times on the rst powered device. 2 Red LED ashes every 2 seconds . This is the network coordinator. Join Mode is open.
- Page 6 All manuals and user guides at all-guides.com Power up Remaining Devices Power up all of the remaining RF baseplates by connecting them completely on the smoke alarm. Red LED ashes 3 times every 2 seconds after joining the network.
- Page 7 All manuals and user guides at all-guides.com Push button twice Pick Any Device Push the LINK button twice on any unit after all the smoke alarms have joined the network. Red LED stops ashing on each unit as network is closed.
- Page 8 all-gui des.co...
-
Page 9: Setup Complete
All manuals and user guides at all-guides.com Setup Complete! If all devices are no longer ashing the Red LED, the devices are now connected. Congratulations! Refer to user guide for detailed installation instructions. - Page 10 All manuals and user guides at all-guides.com Section 2 Adding a Device to an Existing RF Interlink Network...
- Page 11 All manuals and user guides at all-guides.com Push button twice Push LINK Button Twice on any installed unit. To open the RF Interlink Network, push the LINK button twice on any previously connected smoke alarm Red LED ashes every 2 seconds. Join Mode is open.
- Page 12 All manuals and user guides at all-guides.com Power On the New Device(s) Connect the smoke alarm to the new RF baseplate. Red LED ashes 3 times every 2 seconds after joining the network.
- Page 13 All manuals and user guides at all-guides.com Push button twice Choose ANY Connected Device Push LINK button twice on any connected device to close the network. Red LED stops ashing on each unit as network is closed.
- Page 14 all-gui des.co...
- Page 15 All manuals and user guides at all-guides.com Setup Complete! If all devices are no longer ashing the Red LED, the devices are now connected. Congratulations! Refer to user guide for detailed installation instructions.
-
Page 16: Resetting Your Device
All manuals and user guides at all-guides.com Section 3 Resetting Your Device If you encounter an issue at any point during the RF Interlink network setup process, or if you need to remove a device from a network, you may reset the device by following the subsequent directions. -
Page 17: Resetting The Device
All manuals and user guides at all-guides.com Push button twice Resetting the Device Push LINK button twice to open Join Mode. Unit will respond with 2 or 3 ashes, indicating Coordinator or RFD respectively. - Page 18 All manuals and user guides at all-guides.com Push and hold button Resetting the Device Press and Hold button for 4 to 5 seconds. Unit will respond with 4 quick ashes indicating that the wireless settings have been reset and the unit is now a standalone alarm.
- Page 19 All manuals and user guides at all-guides.com Need more help getting started? Visit www.psaproducts.com.au to view video tutorials. Consult the User Guide for more detailed instructions on product installation and use.
- Page 20 all-gui des.co...
Need help?
Do you have a question about the LIFWMB2 and is the answer not in the manual?
Questions and answers