Table of Contents
Advertisement
Quick Links
BATTERY POWERED ALL WEATHER ELECTRONIC IGNITION SYSTEM
Models Covered in this Instruction Set
Product Certifications
This QR Code will always take you to the most recent certifications for the entire Fire by Design
product line.
You can also type in the URL directly: http://fbdqr.com/product-certs
WARNING: For Outdoor Use Only
STOP:
IF YOU SMELL GAS
- Shut off gas to the appliance
- Extinguish any open flame
- If odor continues, keep away from the appliance and immediately
call your gas supplier or fire department
Proposition 65 Warning
Operating, servicing and maintaining this appliance can expose you to chemicals including
Carbon Monoxide and Lead which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more
information go to www.Prop65Warnings.ca.gov
WARNING
Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Read the installation, operating
and maintenance instructions thoroughly before installing or servicing
this equipment
WARNING
Do not store or use gasoline or other flammable vapors and liquids in vicinity of this or any other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
FBD-0004
|
BP AWEIS Ignition System
Battery Models
BPAWEISNG
290k BTU
|
Battery
|
Natural Gas
BPAWEISLP
290k BTU
|
Battery
|
Liquid Propane
BPAWEIS
Ignition System
If you cannot read or understand these instructions,
STOP:
do NOT attempt to install or operate this appliance.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING
For use with NATURAL or LP GAS Only
NO SOLID FUELS TO BE USED WITH THIS SYSTEM
- 1 -
INSTRUCTIONS
REV
|
050925
Advertisement
Table of Contents
Related Manuals for Fire By Design BPAWEIS
Summary of Contents for Fire By Design BPAWEIS
- Page 1 Battery Liquid Propane Product Certifications This QR Code will always take you to the most recent certifications for the entire Fire by Design product line. You can also type in the URL directly: http://fbdqr.com/product-certs If you cannot read or understand these instructions,...
-
Page 2: Table Of Contents
Clearance to Combustibles Ventilation BPAWEIS Installation BPAWEIS Completed Diagrams Remote Positioning of the BPAWEIS Operation of the BPAWEIS Burner System Firetronix App Set Up & Management Maintenance of the BPAWEIS Burner System Troubleshooting the Indicator Light Replacement Parts Media Information & Installation Return Policy &... -
Page 3: What's In The Bpaweis System
What’s in the BP AWEIS System? Below is a list of the contents that each Battery Powered AWEIS system contains. If you purchased a different model that includes a type of enclosure, please refer to that specific model number instruction set. SENSOR IGNITER LED/Bt... - Page 4 Venting the Enclosure for Natural Gas (NG) Natural Gas is lighter than air, therefore any unburned or leaking natural gas will drift up and away from the feature if it has a way out. The illustrations below show how gas ( ) will pool towards the top of the burner pan if there is not proper ventilation for the gas to escape.
-
Page 5: Ventilation
AWEIS Installation STOP: The installation should be done by a Qualified Service Technician that is Locally Licensed Step 1 - Preparing the Enclosure In this set up & instruction set, we will be using a generic non-combustible square enclosure. Center of Burner System Gas &... - Page 6 Step 2 - Attaching the BP AWEIS Ignition Control Module to the Incoming Gas Line There are several different methods to connect the BP AWEIS Ignition Control Module to the incoming gas line. For the remainder of this installation guide, we are going to use the method of attaching the Control Box directly to the Gas Line / Stub. Attaching directly to the Gas Stub Attached directly to the Gas Line / Stub Attached to Gas Line / Stub with Flex Line...
- Page 7 Step 4 - Connecting the AWEIS Pilot Burner Assembly Pilot Burner Assembly LED/bt 1/4” Flare MANUAL Molex Fitting BATTERY STATUS SENSOR IGNITER Switch Igniter LED/Bt Molex Terminals Sensor BATTERY SWITCH Battery Molex Molex Battery powered models may look completely different from their Hardwired counterpart, but they function the same way. Start with the Switch Molex &...
- Page 8 Attaching to the Burner Pan You will need to line up the Opening for the Pilot Burner with the Pilot Burner. You will notice that the hole in the center of the pan (for the pipe nipple coming from the Ignition Control Box) and the opening for the Pilot Burner are much larger than needed.
-
Page 9: Remote Positioning Of The Bpaweis
Remote Positioning of the BP AWEIS The BP AWEIS Box can be only be installed up to 10ft away from the burner. This can be beneficial for scenarios where excess heat could compromise the BP AWEIS box. Up To 10ft Operation of the BP AWEIS Burner System Do NOT use this appliance if any part has been HOT! - DO NOT TOUCH - SEVERE BURNS MAY... -
Page 10: Set Up & Management
You will be presented with the “Find Devices” screen. On the faceplate of your BPAWEIS Switch Panel there is a 3 position rocker switch. Move the rocker to the position marked BT. Once you do, the Battery Status LED will start blinking Blue. This let’s you know that your device is discoverable. - Page 11 Tap “Create New Password” and you will be taken to the “Set Password” page. Type your desired password into the two fields and tap “Save Password”. You will get a dialog box that says your password was saved successfully. Press the X in the top right hand corner of the dialog box. Your new password has been saved. Tap “Create New Password”...
- Page 12 Using the Firetronix App to Control Your Fire Feature To turn on your fire feature: Press the “On” button located on the right side of the fire feature display area. The fire feature display area will illuminate red, and the Switch Panel on the fire feature will blink green 3 times indicating ignition has started.
- Page 13 Re-Ignition Shortly After Turning Off If you try to turn the feature on shortly after turning it off you will see a message pop up saying “FBD Fire Feature in cool down state to clear gas”. There will also be a yellow triangle “caution” Icon that appears. If you try to turn the feature on when you see the yellow caution Icon the LED indicator light will blink yellow.
-
Page 14: Maintenance Of The Bpaweis Burner System
Maintenance of the BP AWEIS Burner System Maintenance should be done by a Qualified Ensure gas & power are shut off and the appliance is cool WARNING! Service Technician. The appliance should be before servicing. Any guard or protective device removed inspected before use and at least annually. -
Page 15: Replacement Parts
Replacement Parts for the Battery Powered AWEIS Burner System Identifier Part # Description BPBA Pilot Burner Assembly BPack Battery Pack Assembly Rocker Switch Assembly LED Light Assembly BICB Ignition Control Module Media Information & Installation WARNING! Do not use any other material as filler/topping media inside fire features other than those listed below. Using improper media inside a fire feature could result in damage to property or injury to persons nearby due to media “popping”... -
Page 16: Return Policy
Return Policy All orders from Fire by Design (FBD) may be returned within 30 days for a full refund. In order to return or exchange (under the warranty guidelines described in the Fire by Design Limited Warranty section of this instruction set) all or part of your order, you must contact us for a Return Merchandise Authorization number (RMA#).
Need help?
Do you have a question about the BPAWEIS and is the answer not in the manual?
Questions and answers