Fire By Design All Weather Electronic Ignition Owner's Manual

Battery powered 3 aa

Advertisement

Quick Links

www.FirebyDesign.com
Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Read the installation, operating and maintenance
instructions thoroughly before installing or servicing this equipment.
Do not store or use gasoline or other flammable vapors and liquids in vicinity of
this or any other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or
any other appliance.
FOR OUTDOOR
USE ONLY
If you smell gas:
Installation must conform with local codes or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1 / NFPA 54, or International Fuel Gas Code.
The appliance, when installed, must be electrically grounded in accordance with local codes or, in
the absence of local codes, with the National Electric Code, ANSI/NFPA 70, if applicable.
ON
OFF
Waterproof
Battery Pack
WARNING
For Use with NATURAL or LP GAS Only
NO SOLID FUELS TO BE USED WITH THIS SYSTEM
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from appliance and immediately call your
gas supplier or fire department.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Battery Powered
All Weather Electronic
Ignition System
WARNING
WARNING
WARNING
DANGER
1
Battery Powered (3 AA)
All Weather Electronic Ignition
Owner's Manual
Installation and Operation
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which
has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such
as a camper, tent car or home.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the All Weather Electronic Ignition and is the answer not in the manual?

Questions and answers

Summary of Contents for Fire By Design All Weather Electronic Ignition

  • Page 1 Battery Powered (3 AA) All Weather Electronic Ignition Owner’s Manual Installation and Operation www.FirebyDesign.com Battery Powered Waterproof All Weather Electronic Battery Pack Ignition System WARNING Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
  • Page 2: Proposition 65 Warning

    Proposition 65 Warning Operating, servicing and maintaining this appliance can expose you to chemicals including Carbon Monoxide and Lead which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to www.Prop65Warnings.ca.gov AVERTISSEMENT Une installation, un ajustement, une modification, une réparation ou un entretien inapproprié...
  • Page 3 Table of Contents Gas and Electrical Requirements Page 4 Pilot Burner Clearances Page 4 Assembly Battery AWEIS System Components Page 5 Installation Page 5 Acceptable Media for Fire Features Page 8 Installation of Media in Fire Features Page 8 Operation Page 9 LP Air Mixer (LP applications only)
  • Page 4 14.0” W.C. / ½ psi Maximum Electrical Requirements The Battery Powered All Weather Electronic Ignition System operates on 3 AA batteries which are installed inside a Weatherproof Battery Pack that is included with the system. Recommended Replacement Batteries: Energizer AA Ultimate Lithium Clearances WARNING –...
  • Page 5 Battery Powered All Weather Electronic Ignition System Components Standard Control Panel Low Profile Control Panel Control Dimensions: 4.5” x 4.5” Dimensions: 2” x 2.5” Panel Ignition Control Box Waterproof Battery Pack Pilot Burner Assembly Installation Installation Note: Installation should be done by a qualified service technician that is locally licensed.
  • Page 6 3. Electrical Connections: The illustration at right shows Pilot Burner where the various components plug into the front panel of Assembly the Ignition Control Box. NO two connectors are the same. This should prevent plugging a component into the SENSOR IGNITER wrong connector.
  • Page 7 5. Install the Burner Pan, bring the Pilot Burner Cage up through the Pilot Burner opening in the pan and secure to the pan using the stainless steel screws supplied. See photo at right. 6. Install the Cover Plates. At right you see two plates that came with the burner pan.
  • Page 8: Installation Note

    Acceptable Media for Fire Features 1” above ring WARNING Do not use any other material as filler/topping media inside fire features other than those listed below. Using improper media inside a fire feature could result in damage to property or injury to persons nearby due to media ‘popping’...
  • Page 9: Operation

    Illustrations showing Completed Installations Illustration of Properly Installed AWEIS Illustration of Properly Installed AWEIS (Natural Gas) (Propane) Pilot Burner Pilot Burner Fire Ring / Burner Fire Ring / Burner Assembly Assembly (Holes Facing Up) (Holes Facing Up) Natural Gas Orifice Burner Pan Burner Pan Coupling...
  • Page 10 2. Turn fire feature on by turning the ON/OFF Switch to the ON position. Sequence of Operation during Ignition - Switch On: LED light begins flashing green indicating ignition is about to begin - Gas Valve opens and spark ignition begins - Ignition occurs almost immediately (assuming gas is present) Fire Feature Shutdown Turn fire feature off by turning the ON/OFF Switch to the OFF position.
  • Page 11: Replacement Parts

    Replacement Parts Part Name Part # Item Letter Pilot Burner Assembly BPBA Battery Pack Assembly BPack Rocker Switch Assembly LED Light Assembly Ignition Control Box BICB Troubleshooting The LED light incorporated in the ON/OFF Switch is programmed to indicate failure modes within the Battery Powered AWEIS System.

Table of Contents