Related Manuals for Monport MEGA
Summary of Contents for Monport MEGA
- Page 1 MEGA Laser Engraver User Manual Please read this manual carefully before using Mega. Following the instructions will help you complete the setup efficiently. The entire setup process takes approximately 120 minutes.
-
Page 2: Table Of Contents
3.3 Verify Laser Output ....................10 3.4 Remove the Camera Cover ................12 3.5 Camera Canvas Calibration ................12 3.6 Familiarize with Mega’s Touch Screen Icons ............ 10 3.7 Distance Sensor Calibration ................14 4. Using MDH to Complete Your First Project ............15 4.1 Place the Honeycomb Board ................15... -
Page 3: Preparations
1. Preparations 1.1 Inspect for Visible Damage Before using Mega, check for any visible damage: Damage to the packaging Deformation of the machine’s outer shell Below are the front and rear views of Mega:... -
Page 4: Accessories Checklist
1.3 Add Coolant (Water Pump Must Be Turned On First, Then the Machine Turned Off) Mega requires coolant (water or antifreeze) before use. Turn on the water pump first to allow circulation and prevent air from entering the system. Use different coolant ratios depending on the temperature. Refer to the table below for... - Page 5 Steps to Add Coolant: Step 1: The machine’s back cover is not screwed in by default. Remove it as shown: Important: If you accidentally disconnect the power cord while removing the cover, reconnect it as shown: Step 2: Unscrew the water tank cap. Step 3: Fill the tank until it’s at least two-thirds full.
-
Page 6: Remove The X-Axis Fixing Bracket
1.5 Connect the Air Duct Hose To ensure proper ventilation, we recommend installing the exhaust duct before using Mega. Step 1: Gather the required parts: duct adapter, duct hose, and hose clamp. Step 2: Insert the duct adapter into the machine. -
Page 8: Configuring Mega's Network Via Mdh
USB is slower and not recommended for long-term use. Step 1: Open M-Design Hub Step 2: Connect the Device via USB Connect Mega to your computer via a USB-Type-C cable (USB-A for the computer, Type-C for the machine), then turn on the device. - Page 9 Step 3: Connect the Device via WiFi After a successful USB connection, your device name will appear at the top right of MDH. Click the settings icon beside it to go to "Device Settings" - "Network Settings". Choose your Wi-Fi network from the list and enter the password to complete the WiFi setup.
-
Page 10: Upgrade Mega's Firmware
2.3 Upgrade Mega’s Firmware Firmware V1.0.0.9 updates automatically via M-Design Hub. Before proceeding, ensure your MDH software is updated to version V1.1.0. If using an older version, you will be prompted to update. Step 1: Click "Yes" to update when prompted. -
Page 11: Preparing Mdh Before Your First Project
Important Notes: Flame Detection Sensitivity: The flame sensor is highly sensitive and may trigger false alarms. If the Mega device sounds an alarm without an actual flame inside, there is no need for concern. The flame detection software is still undergoing sensitivity optimization. -
Page 12: Adjust The Light Source & Focus The Beam
Step 2: Import the device files into LightBurn: Open LightBurn - "Devices" (a) - "Import" (b) Step 3: In LightBurn, click on the "Console" tab. Step 4: Enter the following commands in sequence to set the optimal acceleration and deceleration parameters: \$120 = 3000, \$121 = 3000, \$122 = 500 3.2 Adjust the Light Source &... -
Page 13: Verify Laser Output
Move the X-axis up and down to verify the optical path alignment between the first and second mirrors. If misaligned, use a hex wrench to adjust the first mirror holder. Step 4: Adjust the Second Mirror Place the light target into the laser head. ... -
Page 14: Remove The Camera Cover
Hardware Check: Step 1: While engraving, observe the laser tube to ensure it emits light. Step 2: If the laser tube does not emit light, check the side laser emitter. Ensure the side laser emitter’s green light illuminated (the yellow light should automatically turn on when the machine starts). -
Page 15: Familiarize With Mega's Touch Screen Icons
You can also refer to our complete camera calibration video tutorial: https://drive.google.com/file/d/1bSUxcotalmM20TxAzQ4-d8PSI6onLXo6/view?usp=dr ive_link 3.6 Familiarize with Mega’s Touch Screen Icons The Mega’s front smart button screen displays various statuses of the cutting machine. Refer to the images below for a visual representation of each icon and its corresponding status. -
Page 16: Distance Sensor Calibration
Important: Currently, the device can be controlled by swiping and pressing; rotating the knob is not supported. 3.7 Distance Sensor Calibration If you experience inaccurate material thickness measurements, calibrate the distance sensor to enhance accuracy. Step 1: Go to "Device Settings" - "Correction Tool" - "Rangefinder Adjustment" Step 2: Place the provided 3mm Linden wood inside the device and click the measurement button. -
Page 17: Using Mdh To Complete Your First Project
Place the 3mm plywood sheet at the center of the honeycomb board. 4.3 Refresh the Camera & Import File Step 1: If your Mega device is already connected to the network, you can locate it within the MDH software interface shown below. -
Page 18: Upload File And Start Engraving
Step 2: After clicking, both the MDH software and the machine’s display will prompt "Press it unlock". Press the indicated area to start the engraving process. The final work is as shown. Congratulations on completing your first project with Mega! We look forward to seeing your future creations. -
Page 19: Explore Other Features
5. Explore Other Features MDH Software Operation Manual Mega Batch Filling Guide Mega Curved Surface Engraving Guide Mega Conveyor Belt Batch Operation Guide Mega Common Troubleshooting Mega Daily Maintenance 6. Contact Us Facebook Group: https://www.facebook.com/groups/monportlaserofficial...
Need help?
Do you have a question about the MEGA and is the answer not in the manual?
Questions and answers