Related Manuals for Draper 83811
Summary of Contents for Draper 83811
- Page 1 Original Instructions Version 3 - February 2025 DRILL 83811/84121 Stock No: 83811 Stock No: 84121...
-
Page 2: Preface
All photographs and drawings within this manual are document is part of the product; retain it for the life supplied by Draper Tools to help illustrate correct of the product, passing it on to subsequent holders. operation of the product. -
Page 3: Table Of Contents
2. Contents 1. Preface 1.1 Product Reference 1.2 Revisions 1.3 Understanding the Safety Content of This Manual 1.4 Copyright © Notice 2. Contents 3. Product Introduction 3.1 Intended Use 3.2 Specification 4. Health and Safety Information 4.1 General Health and Safety Precautions 4.2 Additional Safety instructions for Compressed Air 4.3 Additional Safety Instructions for Air Drills 4.4 Residual Risk 5. -
Page 4: Product Introduction
10mm (83811) and 13mm (84121). Any other application beyond the conditions established for use will be considered misuse. Draper Tools accepts no responsibility for improper use of this product. -
Page 5: Health And Safety Information
4. Health and Safety Information Important: Read all the Health and Safety instructions • Ensure that the product is compatible with the air before attempting to operate, change accessories, supply before use. maintain or repair this product. Failure to follow these •... -
Page 6: Residual Risk
4. Health and Safety Information • Where dust or fumes are created, the priority shall be 4.4 Residual Risk to control them at the point of emission to avoid a hazard. The safety instructions in this manual cannot account for all •... -
Page 7: Identification And Unpacking
Please examine it for any signs of damage that may have contact the Draper Helpline; contact details can be occurred during shipment. If any part is damaged or found at the back of this manual. -
Page 8: Assembly Instructions
• When using an air tool with a hose over 25ft long, moisture filter. This will ensure a constant supply of Draper Tools recommends increasing the bore of the dry air at all times, provided it is properly maintained. hose to the next largest available size (i.e. increase 3/8”... -
Page 9: Operating Instructions
7. Operating Instructions Note: Before operating the drill ensure the compressor reservoirs are drained of condensate along all the connected air lines. Check and drain the air line regulator’s water trap & fill up the lubrication reservoir. 7.1 Keyless Chuck (Fig.3) The drill is fitted with a keyless chuck, which negates the requirement for a separate key to secure the accessory in... -
Page 10: Using The Drill
7. Operating Instructions 7.4 Using the Drill Dust and Swarf Drilling Metal • ALWAYS wear safety glasses and a correctly fitted • The drill is suitable for use with metals such as sheet dust when using the drill. steel, aluminium and brass. • A mask rated at least FFP2 should be used if the • To help the drill bit to locate mark the point to be application involves exposure to fine wood dust. -
Page 11: Troubleshooting
• Disconnect air line supply, then turn drill chuck by hand. Reconnect air supply. • If motor fails to turn contact the Draper Tools product helpline for advice. Tool runs slowly. Air flows slightly Rotor vane seized. • Pour air tool lubricating oil into from exhaust. -
Page 12: Warranty
This warranty period covers parts and labour for 6 months from the date of purchase. Your Draper Tools guarantee is not effective until you can produce, upon request, a dated receipt or invoice to This warranty does not apply to any consumable parts, verify your purchase within the guarantee period. -
Page 13: Explanation Of Symbols
11. Explanation of Symbols Warning! Risk of crushing! Read the instruction manual Direction of rotation Wear safety glasses European conformity Wear ear defenders UK Conformity Assessed Wear protective gloves Warning! – 13 –... - Page 14 Notes – 14 –...
- Page 15 Notes – 15 –...
-
Page 16: Contact Details
Product Helpline: +44 (0) 23 8049 4344 Telephone Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 Please contact the Draper Tools Product Helpline for repair and servicing enquiries. © Published by Draper Tools Limited © Published by Draper Tools Limited...
Need help?
Do you have a question about the 83811 and is the answer not in the manual?
Questions and answers