Product Information Installation and Usage Registration Booster Assembly Certification Active Response Headrest Adjustment Lifetime Warranty SecureFit Lap Belt Positioner Install Using Lower Anchors Warnings and General Safety Information Release from Lower Anchors Storing Lower Anchors Child Usage Requirements Use Without Lower Anchors Securing the Child Vehicle Compatibility Overview of Vehicle Seat Belt Systems...
UPPAbaby retailer. The “lifetime” of the product is defined as the period of Canada’s Motor Vehicle Safety Centre at 1-800-333-0371 or go online to use by the registrant for use with his/her children up to 10 years from date of manufacture. For complete UPPAbaby http://tc.canada.ca/en/road-transportation/defects-recalls-vehicles-tires- Warranty refer to page 38.
WARNINGS + GENERAL SAFETY INFORMATION WARNINGS + GENERAL SAFETY INFORMATION WARNING NEVER place this child restraint on a front seat with an airbag. DEATH OR SERIOUS INJURY can occur. An airbag can strike a DEATH OR SERIOUS INJURY CAN OCCUR rear-facing infant restraint with enough force to crack the shell According to accident statistics, children are statistically safer when properly and seriously injure or kill an infant.
Page 5
Child Restraint, unless approved and tested by restraint use. UPPAbaby. Items not tested with this restraint could injure your child. • For vehicles without a back seat, refer to your vehicle owner’s manual. • DO NOT remove or cover up any of the warning or product labels on this •...
WARNINGS + GENERAL SAFETY INFORMATION CHILD USAGE REQUIREMENTS • DO NOT use a child restraint with damaged or missing parts. This child restraint is for use by children who meet Both requirements below: • Read all instructions for additional warnings. •...
VEHICLE COMPATIBILITY – Overview of Vehicle Seat Belt Systems VEHICLE COMPATIBILITY – Overview of Vehicle Seat Belt Systems WARNING PLEASE READ THE FOLLOWING INFORMATION BEFORE INSTALLING THIS CHILD RESTRAINT! Check Your Vehicle’s Owner Manual Vehicle seat belts differ from vehicle to vehicle. This booster is compatible with most vehicle seat belt systems and DEATH OR SERIOUS INJURY CAN OCCUR can ONLY be used with three-point (lap-shoulder) vehicle seat belts.
VEHICLE COMPATIBILITY – Lower Anchors and Tether for Children (LATCH) VEHICLE COMPATIBILITY – Vehicle Head Restraint The (UAS) Universal Anchorage System helps to anchor the booster seat in the car for stability and to prevent it from The back of the booster seat MUST fit tightly against the back of the vehicle becoming a projectile when not occupied in the event of a crash.
PRODUCT OVERVIEW PRODUCT OVERVIEW A SecureFit Shoulder Belt Guide B Upper Seat Cover C Side Impact Pods D Armrests E Cup Holder Attachment F Lower Seat Cover G Lower Anchor Connector Release/ Red to Green Indicator H Rigid Lower Anchor Connect I Backrest Adjustment Button J SecureFit Lap Belt Guide K Energy Response Headrest...
INSTALLATION AND USAGE – Booster Assembly INSTALLATION AND USAGE – Booster Assembly IMPORTANT: This product is NOT to be used without a backrest, and the backrest should never be separated from the base. 1 Lay the Booster Seat Bottom on floor facing up.
Page 11
INSTALLATION AND USAGE – Active Support Headrest Adjustment INSTALLATION AND USAGE – SecureFit Lap Belt Positioner TO ADJUST THE HEADREST IMPORTANT: The lap portion of the belt should rest on the top of the child’s thighs and NOT across The Headrest can be adjusted for best fit to your child and the child’s abdomen.
INSTALLATION AND USAGE – SecureFit Lap Belt Positioner INSTALLATION AND USAGE – Install Using Lower Anchors TO ADJUST THE LAP BELT POSITIONER Lower Anchors can be used to prevent the booster from becoming a projectile in the car when not in use. NOTE: You may have to open the Lap Belt Positioner The Lower Anchor system does not restrain your child.
INSTALLATION AND USAGE – Install Using Lower Anchors INSTALLATION AND USAGE – Release from Lower Anchors NOTE: Before installing the booster, pull the Rigid Lower TO RELEASE FROM LOWER ANCHORS Anchor Connectors to ensure they are fully extended from To release the booster from the Lower Anchors the housing.
INSTALLATION AND USAGE – Storing Lower Anchors INSTALLATION AND USAGE – Use Without Lower Anchors TO STORE RIGID LOWER ANCHOR CONNECTORS TO INSTALL WITHOUT USING LOWER ANCHORS 1 Rotate both Rigid Lower Anchor Connectors back towards With Rigid Lower Anchor Connectors stored, place the booster on seat.
INSTALLATION AND USAGE – Securing the Child INSTALLATION AND USAGE – Securing the Child TO SECURE THE CHILD IN THE BOOSTER TO REMOVE VEHICLE SEAT BELT 1 With the booster correctly positioned in the vehicle and the 1 Grasp vehicle belt near the RED SHOULDER Headrest in the proper position, route the Vehicle Shoulder BELT GUIDE...
ADDITIONAL INFORMATION Remove Seat Cover Remove Seat Cover The Seat Cover can be removed for cleaning. See the CLEANING AND MAINTENANCE section (page 37) for more details. TO REMOVE THE SEAT COVER 1 Release elastic from both sides of the seat bottom at the RED VEHICLE BELT GUIDE.
Remove Headrest Cover Remove Headrest Cover The Headrest Cover can be removed for cleaning. See the CLEANING AND MAINTENANCE section (page 37) for more details. TO REMOVE THE HEADREST COVER 1 Pull on the lower edge of the Headrest Cover to remove the fabric from the slot that runs around the outside of the Booster.
Install Headrest Cover Install Headrest Cover 4 Push the Headrest Cover into the slot on the outside of the side bolster using the fabric tool. Continue to press the fabric into slot under the SHOULDER BELT GUIDE. Repeat for the other side. 5 Continue to push the Headrest behind the Shoulder Belt Guide using the fabric tool.
Install Seat Cover Install Seat Cover TO INSTALL THE SEAT COVER 1 Pull the Lap Belt Positioner through the opening in the fabric, located in front of the elastic webbing on the underside of the fabric. Continue to pull it through the Lap Belt Positioner Cover, wrap the cover around it, and secure with the closure.
Cup Holder Use CLEANING AND MAINTENANCE TO ATTACH THE CUP HOLDER CLEANING FABRICS - Fabrics include: seat, headrest and lap belt positioner cover Push cup holder at a higher angle pushing firmly down until it clicks into place. TO REMOVE THE CUP HOLDER Machine wash in cold water on gentle cycle Dry flat and away from direct DO NOT iron or dry clean.
• Product purchased from an unauthorized retailer. (Approved retailers are listed on our website uppababy.com). Your UPPAbaby product is warranted to be free from any manufacturing defects for a period of 2 years from the • Second owners and users other than the registrant.
Need help?
Do you have a question about the ALTA V2 and is the answer not in the manual?
Questions and answers