Related Manuals for Alula Connect-FLX
Summary of Contents for Alula Connect-FLX
- Page 1 An M2M Services Brand Connect-FLX Security and Automation Hub Connect-FLX™ Security and Automation Platform Installation Guide...
-
Page 2: System Setup
Ethernet connections come standard. Its long-range encrypted wireless receiver easily provides whole site coverage. Integrated sensor translator enables simplified takeovers of existing systems. Wireless arming stations and mobile devices uncouple Connect-FLX from the entry wall and allow it to be installed at a location convenient for Internet and power connections. -
Page 3: Find A Location
Enrollment signals are typically triggered by removing the battery tab or tampering the device. See the specific device manual for more information. • The Alula App, Touchpad programming, and the Enroll Button AlulaConnect dealer portal can be used to enroll and configure sensors. -
Page 4: Rf Signal Strength
Finally, test the system after finishing installation, enrollment, and configuration. Verify proper operation of all installed sensors and peripherals using the Alula app, Touchpad programming, or the AlulaConnect dealer portal. All sensors and peripherals should score at least 25 on the RF signal strength indicator. - Page 5 Connect-FLX LED Guide System Status Indication is provided via the underglow LED on the front bottom of the panel. The LED may all be forced OFF to conserve battery power during an AC power failure. Normal Operation Green • Solid On - Disarmed •...
-
Page 6: Wireless Performance
Using PINPad (See PINPad manual for detailed operation) Disarm the system by entering a valid user code on the number pad. Arm Away by pressing the “AWAY” button until the PINPad LED flashes red. Arm Stay by pressing the “STAY” button until the PINPad LED flashes red. Trigger a panic alarm by pressing the “STAY”... -
Page 7: Smoke Alarms
Trouble beeps can be suppressed so they only occur during a specific window of time each day. • Use the AlulaConnect dealer portal to configure the trouble beep suppression period. • Trouble beeps can be temporarily silenced for 24 hours using AlulaConnect, the Touchpad, a keyfob or the user's mobile app. -
Page 8: Emergency Evacuation Plan
Emergency Evacuation Plan Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: • Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants. •... -
Page 9: Connectivity Troubleshooting
Alula 1. Ensure port UDP 1234 is open in the router/modem settings. Platform 2. Ensure the panel is registered to an account with Alula and the account Connectivity is active. Ensure port UDP 1235 is open in the router/modem settings. The panel... - Page 10 National Electrical Code, Control Unit, consisting of: ANSI/NFPA 70, the standard for Installation • Base Panel: Connect-FLX using 75-00152-00 v1 firmware and Classification of Burglar and Holdup • Backup Battery: RE029 (6V, 2.5Ah, NiMH) Alarm Systems, UL 681, the Standard for •...
- Page 11 User Information - Definitions Report Delay: Consult with your installer to determine if your system is configured with a communicator delay. A communicator delay will prevent a report to the central station if the control panel is disarmed within _____ seconds (default is 30 seconds) after an intrusion alarm is triggered. Note that fire-type alarms and Carbon Monoxide alarms are normally reported without a delay.
-
Page 12: Specifications
FCC, IC ULC-S304, ULC-S545 Specifications subject to change without notice. TRADEMARKS WARRANTY Alula will replace products that are defective in their first five Alula and Connect-FLX are trademarks owned by Alula, LLC. (5) years. FCC NOTICE IC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject...
Need help?
Do you have a question about the Connect-FLX and is the answer not in the manual?
Questions and answers